Jump to content

1987 Ford Sierra Sapphire 1.8L - Earning its keep - see page 28


Peter C

Recommended Posts

Now that my big birthday celebrations are behind me, I can focus on fixing up the Sierra.

The plan was to pressure wash the underside and arches before doing any remedial work to the bodywork. I started by removing the battery and covering up the complicated* electronics and the carburettor. 

162.thumb.JPG.f1d4897483da9fbfae35d62dd8b782fb.JPG

I put the wheels back on, dropped and pushed the car out onto the driveway. Once there, I jacked it up again and took the wheels off.

163.thumb.JPG.be53638e93c9918d7834757024812f3c.JPG

All five wheels and the arch mouldings were also due a good scrub.

164.thumb.JPG.52258e773bed4601b516ae3da08978dd.JPG

An hour later, the underside was clean. Surprisingly little crud came off, the underside was cleaner than I expected and much cleaner compared with all the other cars that I treated to the same process in the past.

165.thumb.JPG.2a7b373ae8750f2fd14ef4076c424e34.JPG

Bits of flaky paint came off but what is left now is not just solid but also clean.

166.thumb.JPG.6adbdc531a123403a33b79dacb8f1974.JPG

167.thumb.JPG.a02070a52ba25a24800295db13ed9a6a.JPG

The plastics responded well to the pressure cleaning and a fair bit of the blue overspray also came off in the process. The road wheels will need a lick of paint, however the spare looks great. It's also fitted with an unused Good Year tyre.

168.thumb.JPG.754b1e1e490add5a0eb80113cd8b6da2.JPG

I let the underside dry for a while before I put the wheels back on again. I pushed the car back into the garage, where I jacked it up AGAIN and took the wheels off AGAIN! 

169.thumb.JPG.9ce998a6ceae14860aea6425bf4d0d8c.JPG

I didn't have time for a proper inspection but first impressions are good, everything looks a lot cleaner.

170.thumb.JPG.5d30ac84e88620f8179b2f7f77e6606b.JPG

171.thumb.JPG.8e02b5d914084c403424e49feb92538a.JPG

Time permitting, I might start on the bodywork repairs tomorrow.

In other news, I wrote to the previous registered owner over a week ago and had nothing back. Never mind.

I received a period Sierra badge from @Six-cylinder and a set of four coasters from @Pat Earrings. Thank you both.

172.thumb.jpg.4218079024d3195ebefd804878b73c11.jpg

More soon.

Link to comment
Share on other sites

  • Peter C changed the title to 1987 Ford Sierra Sapphire 1.8L - RUST - Work begins, see page 13

I spent half my Sunday (yesterday) stripping flaking paint and underseal and preparing surface corrosion for undersealing and painting. I used a circular wire brush attachment fixed to the end of a drill, which made the process a lot easier and a LOT more messy. Good news is that I did not uncover anything nasty. I didn't take any photographs as you have all seen the affected areas before.

The idea was to paint over the underside and low level exposed areas with the matched blue Rust-Oleum paint. I painted a bottom corner of a door and this morning, once the paint had dried, I found it to be a completely different  shade of blue.

173.thumb.JPG.3a2720b8618c1c8b4e6c0f6030c0f837.JPG

I then sprayed over the same patch with the matched aerosol and...

174.thumb.JPG.cec96e9b4422954c5a78bdc4ddd06eed.JPG

Just about a perfect match. Not bad for a colour that is a bitch to match.

I popped back to the paint shop today, showed the man who mixed the paint for me the above photos and he added some grey and yellow to the mix, to make the colour brighter. When I got home, I applied some of the newly mixed paint and it looks a better match but I won't know how much better until the paint dries. The plan is to use the brush on stuff for the areas that aren't so visible and use the aerosol to repair the damaged paint higher up along the flanks, then cut and polish the lot.

In other news, I received a switch blanking plate from @wesacosa (thank you!) to replace the front fog light switch that has no right to exist in an L spec Sierra.

175.thumb.JPG.791c517cf9c60ad7ddc5cc12cfdc3374.JPG

More soon.

Link to comment
Share on other sites

This is heroic work.  And all the right stuff to do for sure.  On my new shell, there were loads of bits underneath that needed seam sealing as they'd done a really poor job of it in the factory.  You may know all this - sorry if so.  Might be worth getting a tin, if you know the stuff (one of the pros on here might know the better brands):

image.png.f781b5dd3511fa1e98a35eb93ae62f2e.png

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...