beko1987 Posted July 10, 2016 Share Posted July 10, 2016 So, yesterday, I picked up a steering column. Happy days, except the ignition barrel has a snapped off key inside it and therefore can't be removed... Does anyone have any experience of getting half a key out of the barrel? The bloke have me the other key that fits the barrel, so if the key can be extracted, the whole key can be used to release the barrel, and if so he would like it back. If not, no bother he said (he wanted it for his van as the steering lock is broken) So, doable in a non destructive way or do I hammer the locking pin back to remove the barrel from the column? I've been offered a loan of a lock pick set with a hook thing if that would help. willswitchengage 1 Link to comment Share on other sites More sharing options...
spartacus Posted July 10, 2016 Share Posted July 10, 2016 Try the lock pick set. If you can see the end of the key it's worth a try. In the past I've used a collection of old dentists tools for this kinds of thing, they're very tough but with very fine points and hook shapes on the end. HMC 1 Link to comment Share on other sites More sharing options...
Tamworthbay Posted July 10, 2016 Share Posted July 10, 2016 Most barrels can be stripped once off the column and it's easy to get it out then. Otherwise a pair of very fine forceps (metal tweezers) can work but usually the springs on the mechanism stop that. If all else fails and it will scrap anyway, I wonder if you make the remaining end into a point and connect it to one half of arc welder, then earth the barrel and insert the bit you have until it touches the broken half and fire it up. No idea if it would work but logic says there is a chance. Link to comment Share on other sites More sharing options...
Eddie Honda Posted July 10, 2016 Share Posted July 10, 2016 dod of superglue on the keyhead stub and ten seconds if it just needs pulling out. EssDeeWon 1 Link to comment Share on other sites More sharing options...
Pillock Posted July 10, 2016 Share Posted July 10, 2016 If you put the rest of the key in, does it turn? If so, remove barrel and then it's his problem Link to comment Share on other sites More sharing options...
AlabamaShrimp Posted July 10, 2016 Share Posted July 10, 2016 Have you tried turning off and on again? Or hammering a bigger key over it? EssDeeWon, pshome, face and 2 others 5 Link to comment Share on other sites More sharing options...
Richard Posted July 10, 2016 Share Posted July 10, 2016 If all else fails and it will scrap anyway, I wonder if you make the remaining end into a point and connect it to one half of arc welder, then earth the barrel and insert the bit you have until it touches the broken half and fire it up. No idea if it would work but logic says there is a chance. That's a nice theory but I think in practice it would arc across every gap in the lock mechanism. Link to comment Share on other sites More sharing options...
Junkman Posted July 10, 2016 Share Posted July 10, 2016 Link to comment Share on other sites More sharing options...
Richard Posted July 10, 2016 Share Posted July 10, 2016 I think a stout screwdriver would turn the lock enough to let you push the release button. Whacking the barrel on the ground might eject the key but could bugger the column. Link to comment Share on other sites More sharing options...
Stanky Posted July 10, 2016 Share Posted July 10, 2016 Cut existing complete cut at the correct point, slide it in to make a complete key in 2 parts. Job's a good'un. beko1987 1 Link to comment Share on other sites More sharing options...
Tamworthbay Posted July 10, 2016 Share Posted July 10, 2016 That's a nice theory but I think in practice it would arc across every gap in the lock mechanism. that was why I said to try only a last resort, who knows what would happen, only one way to find out! Link to comment Share on other sites More sharing options...
Stixy Posted July 10, 2016 Share Posted July 10, 2016 What motor is it ? Link to comment Share on other sites More sharing options...
beko1987 Posted July 10, 2016 Author Share Posted July 10, 2016 Excellent suggestions, I shall try some of them! I don't have the snapped other side of the key sadly, just one complete spare which apparently fits the lock so if key can be removed then it'll fit and turn. Not too bothered about scrapping the barrel though, its the column I want! Ill have a look at it later and try a screwdriver and glueing something to what I can see of the key Link to comment Share on other sites More sharing options...
beko1987 Posted July 10, 2016 Author Share Posted July 10, 2016 Its a cit zx barrel/column too if that helps Link to comment Share on other sites More sharing options...
Guest Hooli Posted July 10, 2016 Share Posted July 10, 2016 I've seen the drop of superglue trick work before, just don't use too much or none of the key will ever come out. As you don't have the rest of the key try it with the end of a thin rod. Link to comment Share on other sites More sharing options...
Timewaster Posted July 10, 2016 Share Posted July 10, 2016 Its a cit zx barrel/column too if that helpsThat explains a lot. The place I used to work cut keys and that style Citroën key was a favourite one to get in two halves. My teenage self was always amused that the blank code was SEX6 I would go with the superglue idea. Link to comment Share on other sites More sharing options...
Station Posted July 10, 2016 Share Posted July 10, 2016 Compressed air on the other end of the barrel if it's loose.If all else fails, and you just want the barrel, drilling out the ignition barrel until it's loose and can be removed. Link to comment Share on other sites More sharing options...
Eddie Honda Posted July 10, 2016 Share Posted July 10, 2016 My teenage self was always amused that the blank code was SEX6 H Davenport number as opposed to Silca SX6? Bloody Simplex locks. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now