Jump to content

Strangeangel's Shite-tastic Shenanigans 12/12 NEW MOTOR - ACHIEVED.


Recommended Posts

I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.

 

So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.

 

Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.

 

Link to post
Share on other sites

Height lever problem: My XM had the same problem with the height lever except it wouldn't go to the lowest setting. Someone suggested that the runner/guides under the car that the shaft runs through can become clogged up with shit and that a clean and lube would be the first step in trying to solve it.

 

RE the tyres: You could probably get away with the 185/65/14's but your speedo will under read by -1.59% plus whatever discrepancy they have from the factory. In other words 30mph = 29.52mph and 60mph = 59.04mph plus whatever the original discrepancy is. Not ideal but better than it reading slower than you are actually going.

Link to post
Share on other sites

You don't want to go too wide on the wheels or tyres, 5.5J best, you might get away with 6 if lucky. They foul on the rear arms, especially if the latter are leaning a bit. Seem to recall I just scraped by with 195/60/14s but 65s (or less) are better.

Link to post
Share on other sites

I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.

 

So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.

 

Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.

The height lever always was stiff, just needed a good tug to get it locked in position.

Link to post
Share on other sites

You don't want to go too wide on the wheels or tyres, 5.5J best, you might get away with 6 if lucky. They foul on the rear arms, especially if the latter are leaning a bit. Seem to recall I just scraped by with 195/60/14s but 65s (or less) are better.

It was running on 6J with 195/60 14 and in spite of the rear arches being trimmed it was hard to get them on and off. Nothing seemed to rub while being driven though.

Link to post
Share on other sites

Check the linkage at the rear (it's all simple mechanical levers, rods and joints) and clean/grease. The handle in the car can take a bit of a pull to stick it in max height, but not to the point of excess. Is that clear as mud?

 

I think the GTis had 185/60/14s on 6" rims, when I ran them they were £200 bangers so used whatever they came with, but I seem to remember the sweetest combination was a car with 175/65s fitted.

 

Any pics?

Link to post
Share on other sites

BX's are ace - and well bought that man.

 

The HP set up is quite easy to live with once you get your head around it and even stripping the doesur (sic) valve isnt the end of the world - somewhere on the internet are some very informative pictures from @Vanny of this parish ( and the BX Project) who has stripped and refurbed one. agreed about having a quick look and lube underneath - but only with the car on axle stands - I really cant stress this enough as Ive had one crush a 2.5L tin of bitumen in seconds when it dropped ( resulting in a North West "Face of Christ" on the driveway for several months). 

 

Ive had 195's on one of mine and apart from needing to slightly modify the rear spats with a piece of wood all was well, but if the rear arm bearings are shagged they will rub.

Link to post
Share on other sites

Height corrector - It's okay, just needs a firm tug to get to the high position.

 

Wheels - It did run 165s when it was on steels. 195 you can get away with on the front (bought some in error but it was a shame not to use them) and 185s will go under the rear but will rub when on lowest setting. Rear arms lean a nib but don't affect the clearance.

 

DO NOT rely on the suspension to get under the car. The rear goes down pretty quickly (an hour or two) but the front stays up pretty well.

 

I know this machine pretty well.

Link to post
Share on other sites
  • 3 weeks later...
  • 2 weeks later...

Still haven't done anything about the LHM escape, largely because of doing-up-the-house type stuff, but also now that one of the 205s CV joints has shat itself the BX is officially Number One Car.

 

I did manage to discover why the throttle action was so heavy though, even with a new cable. The soundproofing under the dash had dropped down and was catching on the very top of the pedal mechanism - now fixed!

Link to post
Share on other sites

Still haven't done anything about the LHM escape, largely because of doing-up-the-house type stuff, but also now that one of the 205s CV joints has shat itself the BX is officially Number One Car.

 

I did manage to discover why the throttle action was so heavy though, even with a new cable. The soundproofing under the dash had dropped down and was catching on the very top of the pedal mechanism - now fixed!

 

Phew. That's good, because BX's can suffer from pedal box collapse. Clutch or accelerator can fail. 

Link to post
Share on other sites
  • strangeangel changed the title to Strangeangel's Shite-tastic Shenanigans 12/12 NEW MOTOR - ACHIEVED.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By Zelandeth
      Well I've been meaning to sign up here in forever, but kept forgetting. Thanks to someone over on another forum I frequent poking me about it recently the subject was forced back into my very brief attention span for long enough to get me to act on the instruction.

      I figure that my little varied fleet might bring you lot some amusement...

      So...we've got:

      1993 Lada Riva 1.5E Estate (now fuel injected, as I reckon the later cars should have been from the factory...).
      1989 Saab 900i Automatic.
      1987 Skoda 120LX 21st Anniversary Special Edition.
      1985 Sinclair C5.
      2009 Peugeot 107 Verve.

      Now getting the photos together has taken me far longer than I'd expected...so you're gonna get a couple of photos of each car for now, and I'll come back with some more information tomorrow when I've got a bit more time...

      Firstly...The Lada. Before anyone asks - in response to the single question I get asked about this car: No, it is not for sale. Took me 13 years and my father's inheritance to find the thing.


      Yes, it's got the usual rusty wings...Hoping that will be resolved in the next couple of months.

       






      Next, a proper old Saab. One of the very last 8 valve cars apparently, and all the better for it. I've driven two 16v autos and they were horrible - the auto box works sooooo much better with the torque curve of the 8 valve engine. Just wish it had an overdrive for motorway cruising...









      Next up a *real* Skoda...back when they put the engine where it belongs, right out the back. In the best possible colour of course...eye-searingly bright orange.







      Seat covers have been added since that photo was taken as it suffers from the usual rotting seat cloth problem that affects virtually all Estelles.

      Then we have possibly the world's scruffiest Sinclair C5...



      Realised when looking for this that I really need to get some more photos of the thing...I use it often enough after all! We have a dog who's half husky, so this is a really good way of getting him some exercise.

      Finally - again, I really need to take more photos of - we have the little Pug 107.



      Included for the sake of variety even if it's a bit mainstream! First (and probably to be the only) new car I've bought, and has been a cracking little motor and has asked for very little in return for putting up with nearly three years of Oxford-Milton Keynes commuter traffic, before finally escaping that fate when my housemate moved to a new job. Now it doesn't do many miles and is my default car for "when I've managed to break everything else."

      I'll fill in some more details tomorrow - I warn you though that I do tend to ramble...
    • By SiC
      Placeholder topic for now. Currently in @Steve79 mums garage but hopefully transported sometime this month. Mostly down to when @worldofceri passes by next. No rush as I have plenty of other projects on the go, just with Spring coming up quick, I'm looking forward to buzzing around in this. So don't expect anything too exciting to happen for a few weeks yet.
      I was hoping the Dolomite would be drivable by now but that's not looking likely. So I'll have to either do the work on this on the drive, cart the Dolomite down to storage over spring/summer or send this off to a professional for it to be sorted. It'll need an MOT anyway, but I'd like to get some of the key things sorted before then.
      Main issues for the MOT:
      Dash clocks don't work. Battery has leaked in the original board and damaged the traces. Have another set of dash clocks here and I hope to make a good one out of the two. Something I'll definitely have to do as most mechanics won't want to touch soldering up PCBs. Brake pedal doesn't fully go to the top of its travel, unless you assist it by pulling it up. I believe the Rev mentioned corrosion at the top of the pedal or something that just needs cleaning odd. Cambelt. This one scares me everytime the engine is started. Label under the bonnet says last changed in 1998 and that's almost certainly true. Steve has done a few hundred miles on it two years ago, but I don't have the guts or will to do a cambelt roulette myself on it. Plus I don't believe they're that difficult to change. Possibly needs some welding on the NSF. I'll clean the area up and if it's small I may do it myself. Alternatively let my local garage pickup on it at MOT time and let them sort it if it's a problem. So hopefully a quick project to get back on the road. That's the intention anyway as I don't have time for too much more, given the Dolomite is taking my time up and the others need fettling too (1100 front calipers and also selling it, MGB service). Likely scenario is getting the above list done so I can drive it to the MOT station and let them sort anything else out needed for that if anything other comes up.

    • By Shirley Knott
      Greetings all.
       
      After lurking here for a short while, frankly liking what I see and enjoying the various shite, the site has well and truly struck a chord with me. I'm a serial buyer of ropey sub £1k vehicles, don't have to but genuinely enjoy it.
       
      I feel like I might (Just might) have found my 'spiritual' home here
       
      I've been posting across the web on owner specific forums (Usually using either my JoeyEunos or RandomPrecion handles) for a while now, but from here-on-in I will pull my threads together and merge them here into one ghastly topic.
       
      My current steeds...
       
      Lupo 1.7 SDI
       
      SAM_5560 by
       
      and the work/story so far...http://forums.clublupo.co.uk/index.php?/topic/102863-joeyeunoss-sdi-beater/
       
      Golf Mk4 SDI
       
       
      SAM_5531 by
       
      and the thread.... http://uk-mkivs.net/topic/597074-project-slow/
       
      Early (1989) Mk1 Eunos (This one was recently sold)
       
      SAM_4656 by
       
      the thread...http://www.mx5nutz.com/forum/index.php?showtopic=213274
       
      Other shite I've owned and moved on in the last year include this ropey Passat...
       
      SAM_6011 by
       
      and this legendary £300 Fiesta Finesse...
       
      Festa by
       
      Cars I'd like to own/actively looking for in the forthcoming weeks/months/years...
       
      Rover 75 (Dizzler)
      Peugeot 405 (XUD)
      Mk1 Octavia (Estate/dizzler, pre pd or SDI)
      Honda CRV (Gen1)
      Volvo 240/850
    • By Peter C
      Woke up this morning, had a little time before I had to leave the house for work, had a quick look at what’s new for sale on Retro Rides and saw an ad for a W124 200E manual, located 15 miles from home. I had no intention of buying a car today but I had to have it! I called the seller and arranged a viewing.
       
      Faults:
       
      2 x rusty front wings (TADTS)
      1 x rusty rear arch
      Needs a polish
      Tracking is out because new track rod end was fitted for MoT
      Engine has oil leak/s
       
      Good points:
       
      It’s a W124 200E!
      5 speed manual transmission
      New clutch
      Brand new MoT
      Superb MoT history
      4 x as new Continental tyres
      Last owner for 15 years, her husband before that for 4 years
      Very tidy MB-Tex interior
      Drives well
      All electrics work
       
      The dealer kindly delivered the car to my house but I managed a pez station shot on route:
       

       
      Plans:
       
      Remove front wings, cut away rust and apply plenty of wob.
      In-situ similar repair for rear arch
      Clean and polish
      Service engine
      Adjust tracking
      Leave patina and enjoy the car as it is
       
      I will update this thread once progress is made.
       

       

       

       

       

       

       

       

       

       
      Hopefully these two will become good friends.
       

    • By JMotor
      Where to start. 
      Maybe with the one that shocked me on how well it turned out? I'll give the shortest version of the story as I can. 
      Got a tip from a friend about a 306 Rallye sat in a barn (it really was! 😂). When to have a look and declared it a mess and thought no sane person would buy it unless it was to break for spares. 
      So I bought it on the spot! 
      All that dust and pigeon crap lovelyness. Why in the hell to people get boners over barn finds!? 
      Anyway. Mechanically it needed everything replacing.
      But managed to score a cheap down at heel GTI-6. It was a striped out car that had an issue with not getting certain gears. Perfect! Gearbox woes were down to a short shift pivot extension being in the wrong place. Moved that back and could get all of the gears. Sweet. 
      I stripped that car and scrapped the shell and spent the next two years on and off swapping over everything. Eventually to a point it was back to a running and driving car again. 
      Clean pass on the first MOT too after being sat for so long 11 or 12 years? I don't know! 
      Puts a big grin on my coupon. But is sat waiting for some better weather and I've a few jobs to do it. 



×
×
  • Create New...