The new news 24 thread

[fordperv]

they are taper but require iirc 310-350 nm

[Angrydicky]

They were both original Ford arms and didn't look like they'd ever been touched. Despite this, they did fail the MoT in 2006 but the bushes on these were so knackered I find it hard to believe that they were actually replaced at that time. The ones I'm fitting are NOS good quality ones (AP and Borg&Beck) so hopefully will last a decent amount of time? I've had plenty of issues with shit modern repro rubber parts so purposely bought NOS.

[Angrydicky]

Basically, almost every major steering, suspension or mechanical component on this car is or was original and completely worn out as it's a 152k, 33 year old Sierra that's spent most of its life crashing over London speed bumps in the hands of an owner who refused to spend any money on it.

[panhard65]

Just ordered the bits to sort the Porsche out £275 for a clutch kit and £570 for an IMS bearing and rear main oil seal. The old bearing had better be on its way out spending this much on it as it is supposed to be a weak point and should be done when the 'box is out.

[SiC]

I'd love to see a post about how you do an IMS bearing. Plenty of cheap Boxsters around where owners run away from them on IMS bearings.

 

Mid-engined German roadsters I thought would be very unfriendly to work on.

[DVee8]

MG production moves to China

 

http://www.bbc.co.uk/news/uk-england-birmingham-37449289

[MarvinsMom]

MG production moves to China

 

http://www.bbc.co.uk/news/uk-england-birmingham-37449289

 

 

well lets be honest, 99.9999%of the assembly was done in china anyway.... at longbridge they were just putting a set of alloy wheels on!

[cort16]

I drove my Panda to work today via rush hour traffic. It didn't break down and nothing fell off, much to my surprise to be honest.

[HMC]

Bbc 4 now lots of French shite as C'etait un rendezvous is being screened.

[captain_70s]

Sent Civic for MOT today, got phone call at work. Phail. Threw £200 worth of repairs at it, passed and collected this afternoon.

 

Can't wait to have a proper car on the road again...

[stuboy]

I not got my car today and fiance wanted take her 3 kids and my teenager to fast food resturant so i fired up my steed

[wuvvum]

I've had a frustratingly unproductive day - had a list of jobs to get done and managed to do hardly any of them.  I got started later than planned as when I took the boat out yesterday (for the first time in ages) I noticed that large areas of varnish on the transom were peeling off and the wood was no longer protected, so first thing this morning I had to scrape the loose varnish off and revarnish the exposed areas, which took a while.  Then it took me ages to fit a replacement pedal to my folding bike, chiefly due to me being a twat and forgetting that left pedals are reverse threaded.

 

After much arsing about I finally managed to get the brake drum off the Rover, but I couldn't see anything that was obviously sticking - the handbrake operates the trailing brake shoe, but the footbrake operates it too and it doesn't stick on when I use the footbrake, so it obviously isn't the shoe that's seized.  There isn't really much else in the way of handbrake mechanism inside the drum - and it must be inside the drum that the binding is happening as otherwise twatting the drum with a hammer wouldn't release it.  I lubed the cable up, but couldn't see much else I could do.  Whilst trying to work out exactly which bits moved where, I pressed the brake pedal like a mong, which caused the unrestrained shoes to immediately self-adjust right to their limit, so I then had to piss about with the self-adjusting mechanism to de-adjust them enough to get the drum back on.  Eventually got everything back together, and would you believe it the handbrake is sticking on just as much as it was before.  So not quite sure where to go from here.

 

Next job was to get the coolant pipe that goes into the bottom of the Volvo's water pump bolted into place.  I hadn't been able to persuade it to line up by hand, but I thought jacking it into place should work.  It didn't.  The pipe is curved, and trying to lift it with the jack basically just pulled it sideways.  I tried putting a screwdriver against the bump around the bolt hole and jacking the screwdriver, but that didn't work either.  The first attempt just resulted in it pulling the jack across the floor; the second attempt got the angle a bit closer but it was actually starting to lift the weight of the car off its springs (before the screwdriver slipped and the whole thing collapsed) - and even then the bolt holes still weren't lined up.  There must be a way of getting the thing into position, but it's got me stumped so far.  The pipe is in there pretty firmly, but it's basically only held in by the rubber seal, and I don't think having a push fit pipe in a pressurised cooling system is a very good idea.

 

I didn't even get time to start on the brake pipe replacement on the Rover, so that's going to have to wait until the morning (along with the second coat of varnish on the boat).  I'd also hoped to do a run to the dump this afternoon, but that didn't happen either - although I did find out that as long as I'm only dumping normal household waste (not trader or DIY waste), I can go in the van without getting charged - which is good as I didn't fancy heaving the washing machine into the back of the CX.

 

To add to the fun, the MGF appears to have sprung a water leak - I was driving to Norwich this evening and noticed the temp gauge had passed its usual one-notch-below-half position and was slowly heading northwards.  I pulled over into a layby and noticed a trail of water drops following the car in.  Looked underneath and water was dripping steadily from somewhere in the middle of the car (couldn't tell exactly where as there's an undertray and the water was coming off that).  I tipped the litre of water that I always carry in the boot of any K-series powered vehicle into the expansion tank, turned round and headed home - I then topped the system right up and it nommed about half a gallon, so it must have been dripping for a while.  I then took it for a 15-mile drive to check that there were no more serious issues, and it behaved perfectly, which was a relief - although I'm still going to have to investigate where the leak is coming from, which has added to my list of jobs to try and fit in over the weekend.  Strangely, even when the coolant level was low enough that the engine was running hotter than normal, the heater was still blowing warm - although I suppose on an F the heater matrix is closer to the rad than the engine is.

[vulgalour]

Bottom of the rad, thermostat housing, coolant pipe along the back of the block and the expansion tank have all been recommended to me as points of water escaping on any K series engine.  I've experienced the first two, seen the third and heard plenty of stories of the fourth being down to crap manufacture cracking the seams when the tank is under pressure.

 

Sent Civic for MOT today, got phone call at work. Phail. Threw £200 worth of repairs at it, passed and collected this afternoon.

 

£200 MoT fail?  What on earth did it need?  The thing's only five minutes old.

[captain_70s]

£200 MoT fail?  What on earth did it need?  The thing's only five minutes old.

Both front brakes were binding and needed to come apart + front pads, also something to do to do with the rear anti-roll bar that I've already forgotten. I was considering taking it home and having a look myself as it's probably nothing hard to do but then I'd have to arrange another lift to work from the parents,  spend another night at their place, actually buy some metric tools etc, etc and I really couldn't be arsed with the whole affair and when they said they could have it sorted for the end of the day it  for a total cost of about £250 I said go-ahead.

 

There are still things I need to sort with the thing, the (not even a year old stainless) exhaust blows when it gets hot and there is a scraping noise coming from somewhere which changes with road speed but is unaffected by braking which I suspect is coming from the O/S/R wheel. This is actually the smallest repair bill I've ever gotten for the thing, I was expecting it to be more around £400, at which point I'd have probably forced myself to do the work!

 

Rather than do that however I got the car back and used my evening to help clear out the shed where the 1850HL is going to welded, a better use of my time I feel.

[twosmoke300]

Wuv - with the sticky rover handbrake I expect it will be the pivot on the trailing shoe where the handbrake arm attaches . That will be seized up

[Richard]

I replaced the drums and shoes on the Punto earlier this year and the handbrake started sticking almost immediately. It turned out that the handbrake pivot on one of the new shoes was seized solid. Even when I managed to free it off the spring wasn't strong enough to return it reliably. Cheers GSF. A set of Ferodo shoes and a decent spring kit had everything working properly.

[twosmoke300]

Quite a few new shoes have stiff handbrake arms . Bit of grease and movement usually frees them off . It does on apec stuff anyway and I tend not to fit anything else

[Richard]

This set wasn't usable. I got the arm freed off eventually but the spring didn't even reach the "off" position.

[scaryoldcortina]

To add to the fun, the MGF appears to have sprung a water leak - I was driving to Norwich this evening and noticed the temp gauge had passed its usual one-notch-below-half position and was slowly heading northwards.  I pulled over into a layby and noticed a trail of water drops following the car in.  Looked underneath and water was dripping steadily from somewhere in the middle of the car (couldn't tell exactly where as there's an undertray and the water was coming off that).  I tipped the litre of water that I always carry in the boot of any K-series powered vehicle into the expansion tank, turned round and headed home - I then topped the system right up and it nommed about half a gallon, so it must have been dripping for a while.  I then took it for a 15-mile drive to check that there were no more serious issues, and it behaved perfectly, which was a relief - although I'm still going to have to investigate where the leak is coming from, which has added to my list of jobs to try and fit in over the weekend.  Strangely, even when the coolant level was low enough that the engine was running hotter than normal, the heater was still blowing warm - although I suppose on an F the heater matrix is closer to the rad than the engine is.

It's most likely to be the long steel pipes leaking, that's all there is under there and they rot for fun. Also, when topping up don't forget the three bleeders (rad, heater and engine) or trapped air will cause more leaks to happen.

[crapcarcollector]

Cheap trailer tent you say?

 

I might have something right up your street.....

 

 

Sent from my iPhone using Tapatalk

 

That picture is from a couple of years ago. I've always kept it undercover.

 

Suffered a bit of wind damage (bent poles on awning) so wants a good sort out

 

It's a good tent with good life in it but wants erecting and sorting out which I haven't done.

 

All usual stuff, 6 berth, pup tents, cooker, sink etc.

 

£100 from a shitter to be gone. Located in ST5

 

 

Sent from my iPhone using Tapatalk

[dean36014]

Definitely interested in the trailer tent, any make and model details so i can google. Is it wired for electrics?

[stuboy]

Mondeo gone off to be mot'd

[Kiltox]

Fucked Citroen C3 has landed.... got it out of economy mode easily enough but still no start. Waiting for the BSI to shut down so I can disconnect the battery again and check the awkward to get to maxi fuses

[catsinthewelder]

Finally got the cracked sump off the 405 this morning. It would have been an easy job on a car without air conditioning. As it was the alternator and everything around it had to come off too to get to the upper mounting bolts on the compressor.

 

 

[tooSavvy]

having a spot of lunch.... Lad at bar offers to pay his round with a 'newfangled' poly £5 note.

 

It has torn almost in two

 

 

Only been out a week... Kwalitee produkt, eh?

 

 

TS

[Kiltox]

having a spot of lunch.... Lad at bar offers to pay his round with a 'newfangled' poly £5 note.

 

It has torn almost in two

 

 

Only been out a week... Kwalitee produkt, eh?

 

 

TS

Probably due to the amount of people who go "oh you can't tear them" *rip*

[dave21478]

Fucked Citroen C3 has landed.... got it out of economy mode easily enough but still no start. Waiting for the BSI to shut down so I can disconnect the battery again and check the awkward to get to maxi fuses

Is it a spazz-tronic automated manual?

 

If so, ignition on and throw 12V onto the starter solenoid and see if it cranks.

When my C2 (basically the same car) wouldnt start it was the clutch actuator that had failed. With its computer unable to tell if the clutch was engaged or not it wouldnt let the engine start. 12v on the solenoid started the engine and it ran fine. Apparently a not-uncommon occurance.

[Kiltox]

Nah it's manual. Error codes in the BSI, think it's toast.

 

Going to chuck a used ECU, BSI and key set in it I think

[Asimo]

Happy afternoon de-rusting the n/s sill on the Connect.

Thank goodness for zinc coated steel! Rust minimal despite the thinnest paint ever.

Amazing stuff that Deox gel.

 

Hope the rain stays away until I can get some zinc primer on. Stonechip tomorrow.

[17-Coffees]

Been tasked with trying to help sell my brothers 307 diesel...

 

It's a face lift, 1.6 diesel with not much over 100,000 on the clock, and 10 months MOT.

How much are they worth?