Jump to content

gm's unhealthy obsession with mx5s - squeezing in a few last drives before Exo goes into hibernation


gm

Recommended Posts

14 hours ago, gm said:

the long bolt fixing the rear offside lower arm is seized in the hub carrier - no amount of plusgas and abuse with the windy gun will shift it :( 

IMG_2219.thumb.JPG.e17a93743d2a15890eaadeba3b72b4f7.JPG

but that's a mighty tighty space to get the grinder in

 

I see you managed but I reckon you could've used a junior hacksaw blade in there.

Link to comment
Share on other sites

5 hours ago, paulplom said:

I see you managed but I reckon you could've used a junior hacksaw blade in there.

It would have taken all week though :( I'm too busy lazy for that !

Link to comment
Share on other sites

Ideally would be the headlight covers (going to modify into cold air intakes), the metal door window trim (mine is rusty), tombstone (to adapt for gauges), grill if it is spare and indicators is still about.

I can top up the Exocet fund :-)

Those bolts are utter twats - they seized solid in the middle for mine.

Link to comment
Share on other sites

I'm looking to sell the headlight units complete but if no one wants them like that, I'll save you the lids. The rest is no problem, I'll put them aside for you.

Do I remember you doing polybushes for one of your mx5s ? The bushes on my wishbones aren't the best so it makes sense to change them before getting stuck into the build but they do seem to be rather expensive for what they are - even the cheaply eBay ones are over a ton for a set and it looks like an arse fitting them :( any advice gratefully received :) 

Link to comment
Share on other sites

I got a full set from eBay. I haven't finished putting them in as AVO went to the scrapyard and I was intending to do BAL but then bought the turbo. Still sitting in my garage along with camber bolt set.


The cheap ones are fine but you will need a press. Don't bother otherwise as they are a right pain.

More expensive ones are split bushes so easy to fit.

Link to comment
Share on other sites

So the best way to go would be to find a set of arms that have already been bushed ? As it happens, there's a guy on the facebook selling such a thing but the fucker isn't responding to my messages :( buggernuts 

Link to comment
Share on other sites

So the best way to go would be to find a set of arms that have already been bushed ? As it happens, there's a guy on the facebook selling such a thing but the fucker isn't responding to my messages  buggernuts 
Yes probably. Or borrow someone's press .. or chuck some money in the biscuit fund of a local garage or just get the more expensive ones but only the ones you need.

I am going to see if I can borrow a press to get mine in. Then get then fitted with full set of camber bolts, before getting AVO alignment.
Link to comment
Share on other sites

I'll see if Andy (scaryoldcortina) might be able to help there :) 

right then, today's progress

first off, I almost missed the postie as I was mid Jim Bell but managed to catch him as he was sticking the red card of doom through the letterbox (the postie, not Jim bell, that would be weird) - I now have some (not all) of the bits needed to sort the engine, diff and gearbox.

a coffee and a bit of procrastination later, a nice chap arrived from Leeds to buy the soft top roof - mazda chat was had and he disappeared leaving me with no option but to do some actual work

so I broke out the tools and pinged (pung ?) the clutch off

IMG_8809.thumb.JPG.75cfa8a60a37811b3e2445d9f40e5e34.JPG

which would have been a bugger had I not thought of using @junkyarddog 's crank locking tool - handy piece of kit, that.

IMG_8810.thumb.JPG.ede11613824242799ceb143fd06f2009.JPG

the clutch, it would seem, is bollocksed

IMG_8812.thumb.JPG.649308f6c9f5bcb8a3451c97ab85341a.JPG

pressure plate and flywheel have had a hard time too 

IMG_8811.thumb.JPG.998cbf6476dd62af11bdaf5dd269ecac.JPG

hmm, should I fit a lightened flywheel, I wonder

IMG_8817.thumb.JPG.76c894b656a00fe8fe421c0acf1e38ff.JPG

yes, I probably should !

lots more petrol based cleaning and we have

IMG_8823.thumb.JPG.01e87015d899823832a7f1e69494bd4b.JPG

then someone else turned up to buy the wind blocker - more mazda chat and pointing at engines ensued

but now it's time to have a go on the cam cover. 

I've been aware of the presence of a dishwashing machine in the kitchen for a while now, I'm quite content washing up by hand so have never investigated if it actually works. 

Let's find out then !

IMG_8826.thumb.JPG.b6ef06e46c4e9ab95e8197a6987e2543.JPG

Intensive :) that's the one for me 

IMG_8827.thumb.JPG.a2e7d3891c4ae8f39e818a94b3be91b3.JPG

and we shall see what happens in a while - it's been making sloshing noises for a good hour now, hopefully there will be shiney parts a plenty when it's done it's thing.

 

almost forgot, I found the engine number under all that grime

IMG_8818.thumb.JPG.333444e126aaf61fc4b752b9413a436d.JPG

Link to comment
Share on other sites

If you're never going to use that dishwasher you could go the whole hog and clean a diesel egr valve and inlet manifold.

I'm actually curious as to whether a dishwasher could manage that.

  • Like 2
Link to comment
Share on other sites

Fuck me you're brave. I might put a cheeky washer bottle in the dishwasher when swmbo is out but a cam cover would see a frost settle on the marital relationship.

  • Like 1
  • Haha 2
Link to comment
Share on other sites

8 hours ago, cort1977 said:

Fuck me you're brave. I might put a cheeky washer bottle in the dishwasher when swmbo is out but a cam cover would see a frost settle on the marital relationship.

you'd be right there but there's no current mrs gm to spoil the fun :)

 

  • Haha 2
Link to comment
Share on other sites

so what did I find when I opened the door this morning ?

IMG_2249.thumb.JPG.576675ef82c3070a93cc77585aaecd00.JPG

IMG_2252.thumb.JPG.5408c1659419aa4d6bc811128c7f5775.JPG

well, yes, it IS cleaner but what's all this powdery shit everywhere ?

IMG_2254.thumb.JPG.1645fcd2bf5c2f4f5232b05db863f531.JPG

IMG_2253.thumb.JPG.9d36bd086a22b84edb1106ab974b9626.JPG

I blame the Powerball (pinched the posh tablets off me mam)

thankfully, it just rubs off

IMG_2255.thumb.JPG.8bae2eec2e8e3cab07cd8b3aeb62e713.JPG

but is going to be a pain cleaning all of the baffled bits inside :(

 

  • Like 1
Link to comment
Share on other sites

I took it outside and gave it a good hosing (!) but the residue was persistent. time to break out the big guns - a good rub down with thinners had it all smooth again, but still not very presentable.

on the shelf next to the paint thinners, I happened across a half full can of wheel silver

that'll do the trick

IMG_2258.thumb.JPG.c9082bc9abc82c84b6fd7bcd2b0ec993.JPG

IMG_2256.thumb.JPG.3f2bd4ec7b3697f4a03d2ea94eb3432c.JPG

not sure that stone chip was the best choice to do the crank pulley though ? looks like melted liquorice :)

IMG_2257.thumb.JPG.cc88a97eb80142691da1471d4954970a.JPG 

 

Link to comment
Share on other sites

meanwhile, the postie had been

gaskets ahoy

IMG_2250.thumb.JPG.94c6b0862997322bbfe66fbc2710f9ea.JPG

plus the one that was missing from yesterdays parcel - that's bloody good service from Andrew at Autolink

IMG_2251.thumb.JPG.e8e346d5db1a7645b1e51171d066659a.JPG

so todays task was to get stuck into replacing various engine seals

camshafts

IMG_2265.thumb.JPG.4f22a05ae5d530ff9785f72c69fd7949.JPG

cam angle sensor (was so old, it fell apart when I removed it)

IMG_2260.thumb.JPG.a658c1146f0c85496c21c40f9f36b4d5.JPG

IMG_2266.thumb.JPG.e805b37beaada8b6f49259289e1563ba.JPG

crankshaft front and back

IMG_2269.thumb.JPG.e12aa95a434fdf1f076bc3947a58a098.JPG

a new timing belt went on, I wire brushed the manky thermostat housing, popped in a new 'stat and fitted the timing covers

IMG_2270.thumb.JPG.80fbfb166fe7c95630ea54523158e0b4.JPG

the cam cover is still drying so will go back on tomorrow.

but this weeks Top Tool Tip would be to get yourselves down to Wilkos and pick up a set of these little chaps - made pulling those seals so easy - and they only cost £2 for the set :)     

 

IMG_2263.JPG

  • Like 3
Link to comment
Share on other sites

good news is that the dishwasher appears not to have come to any harm, there were a few rusty flakes in the filter but, once I clean that out, i can't see that anyone would be any the wiser. I am annoyed that I didn't think of bunging the coolant tank in last night, it's grim :( 

Link to comment
Share on other sites

13 hours ago, snagglepuss said:

Second half of this video he fits new polybushes
 

so two piece bushes are easier to fit than one piece bushes ? how much work would it be to cut cheap eBay one piece bushes in half, I wonder ? 

Link to comment
Share on other sites

On 5/27/2020 at 8:12 AM, loserone said:

London snot, never heard that before.  

It's a 70s & 80s thing , every trip to London resulted in black snot , last time I went was about 5 years ago , no coal fires meant it's no longer a thing

 

I wish I had the skills to do something like this, I've got the perfect donor car , a 97 Mk2 that's great mechanically but really crap bodywork, loads of dents in it

Link to comment
Share on other sites

On 5/27/2020 at 5:19 AM, 1duck said:

Mx5s feel so much nicer de-power steering'd, I always think they are over assisted as standard.

We fitted power steering to a none powered steered mx5. 

???

  • Like 2
Link to comment
Share on other sites

My old G reg mariner blue one had manual steering which I thought was smashing out on the open road or track but was a bit of pain in daily use. When I changed from 15" to 14" wheels with a slightly narrower tyre, low speed manoeuvres were notably easier.

For a daily driver, power steering is a good thing but the kit will be a fair chunk lighter and  certainly won't be in daily use so de-powering is the way for me. I can always reinstate it if needed later on.

IMG_0041.JPG.f6042aed8327053c9d940aae8b095d92.JPG

^Croft

IMG_0002.JPG.738688913318784c952e1d0b4c806b6d.JPG

^Knockhill

  • Like 3
Link to comment
Share on other sites

1 hour ago, Wack said:

I wish I had the skills to do something like this

me too ! it's been a bit of a learning curve but I'm enjoying it so far :) 

  • Like 3
Link to comment
Share on other sites

45 minutes ago, New POD said:

We fitted power steering to a none powered steered mx5. 

???

to be fair my other half complained at first, because it does make it a bit of a pain to park...but i wouldn't say it's any worse than a 1980s un assisted golf, could do with a slightly bigger steering wheel for extra leverage, but all in all not bad.

Link to comment
Share on other sites

It is rather satisfying to be actually putting something back together after so many hours of taking it apart

IMG_8854.thumb.JPG.80bf0fdc169122db8e98ccf9fce74edf.JPG

the intake manifold rather lets the side down now :( 

IMG_8855.thumb.JPG.58707f52f48c17209d772126e336f31d.JPG

but overall an improvement.

In the first pic, notice how the shelf above the engine is sagging under the weight of my stereo, fixed in pic 3 by cunning use of a curtain pole :) 

IMG_8856.JPG

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...