PhilA Posted June 11, 2019 Author Posted June 11, 2019 I started tonight from inside the car, with the intention of removing the toe board panels that surround the brake pedal, in order to remove the brake pedal. Little wonder this would catch on the brake as it was depressed; some ham-fisted person had smashed it into place and tightened it down on the squint. Bashed it straight with a hammer, rubbed it down and applied rust converter. Etch primed then painted in Nearly The Correct Blue. Rinse and repeat 2x more. Need to buy some sheet metal bolts to hold it all together, half of them are missing. Didn't get to pulling the pedal off, that's a task for tomorrow. Phil DeeJay, paulplom, stonedagain and 2 others 5
PhilA Posted June 12, 2019 Author Posted June 12, 2019 First plate in place. Correctly. Sound deadening fitted. Top halves in place. Viewed from engine bay. Everything cleaned up and painted will look nice. Phil rainagain, somewhatfoolish, stonedagain and 10 others 13
PhilA Posted June 12, 2019 Author Posted June 12, 2019 Tonight's hugely inspirational update is brought to you by 88¢ of bolts. I also found a piece specific to "H" VIN cars- clutch pedal blanking plate. Cleaned that up and threw a bit of paint onto it, can fit that up onto the toe-board. I pulled my back out last night so updates may be slow... Phil
PhilA Posted June 13, 2019 Author Posted June 13, 2019 I hadn't thought to offer the blue up against the car. That's not a bad color match for something off the shelf at Wal-Mart. Said plate fits into the first piece of the assembly right there. All fitted in and held down correctly. No squeaks, clanks, rattles. Very good! Phil scdan4, Skizzer, Tickman and 2 others 5
busmansholiday Posted June 13, 2019 Posted June 13, 2019 Is that a good old foot operated high low headlight switch to the left of the brake peddle? LightBulbFun 1
busmansholiday Posted June 13, 2019 Posted June 13, 2019 1 minute ago, hairnet said: Mini in disguise You'd need a floor operated starter button and a little grreen light on the end of the indicator stalk as well for people to mistake the two!
PhilA Posted June 13, 2019 Author Posted June 13, 2019 7 hours ago, hairnet said: Beetle ? Wash your mouth out with soap Phil
LightBulbFun Posted June 13, 2019 Posted June 13, 2019 2 hours ago, PhilA said: Wash your mouth out with soap Phil did someone say Foot operated switch?! *runs away before getting shot* (to be pedantic to my self, IIRC thats actually something to do with releasing the "hand" brake...)
PhilA Posted June 14, 2019 Author Posted June 14, 2019 3 hours ago, hairnet said: ? corn head grease?? why corn head yall Goes in the gearbox at the head of a corn picking machine. Apparently the shafts take a beating and the grease likes to come out. So, the grease is designed to become moderately fluid where it's worked, and slump over when it's stopped. Where it's not worked it remains moderately solid and doesn't liquefy and run through poor seals. Phil paulplom and LightBulbFun 2
PhilA Posted June 14, 2019 Author Posted June 14, 2019 A little work again tonight. The day cooled off enough to work outside. I couldn't get the clevis pin to budge whilst on the car, so I unscrewed the master cylinder shaft out and pulled it off that way. Straightened and cleaned the adjuster shaft, ran a tap down the threads and painted it up. Cleaned up and painted the brake pedal. I think possibly someone had been neglecting the lubrication schedule. Cleaned up the clevis pin, grease nipple and rubber pad. That concludes tonight's work. Paint is drying. Phil adw1977, somewhatfoolish, Asimo and 4 others 7
PhilA Posted June 14, 2019 Author Posted June 14, 2019 I now have a hairpin for my clevis. Rub rub sand sand clean clean paint Phil Skizzer, somewhatfoolish, DeeJay and 3 others 6
PhilA Posted June 15, 2019 Author Posted June 15, 2019 I need to go to the hardware store and see if there's anything I can find to repurpose as a dual pipe clamp. When taking the lower heater pipe out I saw that there's a screw hole in the frame where the pipes pass through, to stop them chattering. Also to note, both heater matrices were disconnected when I got the car, with the heater circuit bypassed. Upon removing the rubber hose, I was presented with clean yellow coolant. This is a good thing; means at least the lower matrix has had anti corrosive mixture in and by the looks of it has no major leaks. The heater valve is all covered in staining, so I'm guessing either the valve or the matrix (or both) are toast. I am going to remove the defroster heater box, partly because I want to paint around and behind it, partly to replace the seal that's turned to so much tar and the rest to check the matrix, flush it and see if the valve is any more good. Phil RayMK, egg, mercedade and 4 others 7
tooSavvy Posted June 17, 2019 Posted June 17, 2019 My Toyota uses a bowden wire/twist tap to control the heater water flow. Boring BUT Reliable.... Watching you comb through this motor is really interesting - I must say my watching ColdWarMotors has made me very aware of model/make similarities and (of course) Jonathan W for how to get them running! Keep at it m8 loserone 1
PhilA Posted June 17, 2019 Author Posted June 17, 2019 This has a thermostatically controlled bellows valve, to keep the cabin at the temperature you dial it to (calibrated in the range of cool to warm). Apparently they are known to leak. One type you cannot take apart, the other is able to be repaired. I don't know what type mine is, so the upper heater box needs to come out and apart to find out. Also there's going to be years of detritus in the defroster heater. It's also a lot easier to remove the nuts from it with the dash removed. Phil tooSavvy 1
PhilA Posted June 18, 2019 Author Posted June 18, 2019 One Harrison upper heater box. ...which has been leaking. Ludicrously complicated thermostatically controlled valve appears to be the culprit. Pulled the rest of it apart to clean and paint. A big gap remains. I need to figure out how to remove the fan and ducting to replace the fan motor with a 12V version. The heater matrix flushed through fairly clean. It certainly isn't blocked, and doesn't appear to leak, either. Next up, catalog to see if there's a replacement valve available, and at what cost. Phil purplebargeken, stonedagain, somewhatfoolish and 2 others 5
paulplom Posted June 18, 2019 Posted June 18, 2019 Great thread this mate. Very interesting. I wish I had the time and space. PhilA, LightBulbFun and stonedagain 3
PhilA Posted June 18, 2019 Author Posted June 18, 2019 I am glad for the workshop here, that much is true. It beats having parts of the car stacked up in the car or in the house, and is much better than being outside on a sloping gravel and dirt driveway like at our last house. As for the time- right now I'm trying to make the time to see if I can beat the deadline of September to get it back on the road. 1-2 hours after work if the evening allows. Phil LightBulbFun and stonedagain 2
hairnet Posted June 18, 2019 Posted June 18, 2019 On 6/13/2019 at 9:14 PM, PhilA said: Wash your mouth out with soap Phil Floor hinged pedals also
PhilA Posted June 18, 2019 Author Posted June 18, 2019 Yes, but they used the flexibility of the plastic to provide a floor mounted pedal. This one has an actual hinge... The brake pedal is chassis-mounted, if you want to be pedantic Heater valves appear to be available as a rebuild/core item. They are, however, expensive. --Phil LightBulbFun 1
hairnet Posted June 18, 2019 Posted June 18, 2019 If you put in heater control valve Pontiac into Google there's valves for 5 quid Could adapt those? Saw this tho http://www.heatercontrolvalve.com PhilA 1
PhilA Posted June 18, 2019 Author Posted June 18, 2019 Ebay7 - RANCO heater valve That's the correct one for the car but the rubber is 60+ years old and I don't like the price There's places that service and rebuild these valves for less so I think I'll go with that option, that way it's got modern rubber parts in that shouldn't spring a leak upon being pressed into service. --Phil
busmansholiday Posted June 18, 2019 Posted June 18, 2019 9 minutes ago, PhilA said: that way it's got modern rubber parts in that shouldn't spring a leak upon being pressed into service. --Phil Bit like saying the Titanic was unsinkable. tooSavvy, PhilA and stonedagain 3
PhilA Posted June 18, 2019 Author Posted June 18, 2019 Fan motor is PM354 - Siemens or VDO. Mental note. --Phil
PhilA Posted June 18, 2019 Author Posted June 18, 2019 3 hours ago, hairnet said: http://www.heatercontrolvalve.com I may give this guy a call.. seems to be fair price also. I consider new neoprene parts to be better than decades old gutta-percha rubber. The only downside is the valve would be away to be fixed for a while. --Phil scdan4 1
hairnet Posted June 18, 2019 Posted June 18, 2019 12 minutes ago, PhilA said: Fan motor is PM354 - Siemens or VDO. Mental note. --Phil https://www.ebay.com/itm/HVAC-Blower-Motor-VDO-PM354/323664889406?epid=78879898&hash=item4b5bee463e:g:sd8AAOSwL~Fbled~
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now