jakebullet Posted September 9, 2021 Share Posted September 9, 2021 I've been under the disco armed with my trusty air needle gun. Found a few holes This is what's annoying about getting garages to do welding, they use the minimum amount of plate, and surprise! you've got a hole next to where they've plated. Then there's the weird "scabs", where the surface of the plate has gone but solid underneath. Except scab on the side next to the fuel tank also has a crack in it. N another crater on the offside. It's like there's chunks of "not steel" in the steel. Fortunately apart from the gaping holes it's solid, as my 30 year old migmate only works on the top power setting. I can do pigeon shite: The one at the side of the tank was more of a bastard as I don't want to take the tank out, but also don't want to melt it. So I welded a bit, cooled it down with wet towel, repeat. Except when I came to do the top edge I can't get the torch in. Had to get the sealant gun out stick welder, and bend an electrode. Obvs I left the slag on to make it look more pretty and will have to be liberal with the underseal. Mega pigeon / MOT standard: Not sure what to do with the crater on the right of the pic above? It withstands 90 psi needle gunning. Also not sure about wheel arches. There's this spot where the underseal has failed: I'll grit blast the rust spot and treat, but should I remove all the underseal for if there's more nasties hiding? Or a new coat over the top of all sound* underseal? Ultimate plan is to fit a new rear chassis, but just haven't got time or facilities. So shonky 3mm plate to hold it together for another year. EightMegs, theshadow and warch 3 Link to comment Share on other sites More sharing options...
sierraman Posted September 9, 2021 Share Posted September 9, 2021 That second to last picture isn’t MOT test standard, it’s not an obvious seam weld. Smear a feckton load of Tigerseal over that before presenting for test. Then a thick coat of underseal on a 4 inch brush. Cue Pass and advise. motorpunk and twosmoke300 2 Link to comment Share on other sites More sharing options...
jakebullet Posted September 9, 2021 Author Share Posted September 9, 2021 I'm thinking there's plenty of weld stuck on it, so an angle grinder flap disk session will make it look more weld like. I'd have had a go today but it started raining and Simon Mayo came on the radio so I had to stop. Link to comment Share on other sites More sharing options...
Minimad5 Posted September 9, 2021 Share Posted September 9, 2021 I'd flap it back and let the MIG fill in the gaps. Get some R.E from buzzweld and cover the lot with a nice coating. Then when that goes off bang some C.I.O (or similar) over the lot. It should last a few years and look better then. Well done for tackling it and not being put off. JMotor and jakebullet 2 Link to comment Share on other sites More sharing options...
Bren Posted September 9, 2021 Share Posted September 9, 2021 Watch this. So satifying. juular, Isopon and warch 3 Link to comment Share on other sites More sharing options...
somewhatfoolish Posted September 10, 2021 Share Posted September 10, 2021 No wonder detroit motors get such terrible fuel economy; there's more metal there than in the Forth Bridge. Link to comment Share on other sites More sharing options...
Minimad5 Posted September 10, 2021 Share Posted September 10, 2021 10 hours ago, Bren said: Watch this. So satifying. Wouldn't do that on the P4, be nothing left 😅. Why is he using a chisel tool, and not the needle / scale gun attachments 🤷♂️ Link to comment Share on other sites More sharing options...
JMotor Posted September 10, 2021 Share Posted September 10, 2021 10 hours ago, Minimad5 said: Get some R.E from buzzweld and cover the lot with a nice coating. Then when that goes off bang some C.I.O (or similar) over the lot. 1+ for Buzzweld. I like the R.E and the WAR undersealer too. Link to comment Share on other sites More sharing options...
Minimad5 Posted September 10, 2021 Share Posted September 10, 2021 2 minutes ago, JMotor said: 1+ for Buzzweld. I like the R.E and the WAR undersealer too. I've got a good 10 maybe 12 folk onto it, wish I'd got shares in the place 😅 JMotor 1 Link to comment Share on other sites More sharing options...
jakebullet Posted September 10, 2021 Author Share Posted September 10, 2021 Just been to A&E for a grinding spark removing from my eye. Ungrateful bastard thing! Top tip: avoid wilko goggles. somewhatfoolish and lesapandre 1 1 Link to comment Share on other sites More sharing options...
Ian_Fearn Posted September 10, 2021 Share Posted September 10, 2021 Same thing happened to me last week. It’s very sobering to think how much worse it could have been. I got a bit stuck just outside my field of vision but a few mm in the wrong direction and……. lesapandre 1 Link to comment Share on other sites More sharing options...
Minimad5 Posted September 10, 2021 Share Posted September 10, 2021 1 hour ago, jakebullet said: Just been to A&E for a grinding spark removing from my eye. Ungrateful bastard thing! Top tip: avoid wilko goggles. I swear by the following: Bolle Tracker II Safety Glasses Get them from Amazon for about £8 or £9, yes that is expensive for one pair, but good luck buying a new set of eyes. Ooh and they come with string too, so they don't fall off (Get a clear set and an orange set, as I find the orange ones are brilliant in bright sun) lesapandre and theshadow 2 Link to comment Share on other sites More sharing options...
red5 Posted September 10, 2021 Share Posted September 10, 2021 Those are bob-on. We use them at work. twosmoke300 and Minimad5 2 Link to comment Share on other sites More sharing options...
twosmoke300 Posted September 10, 2021 Share Posted September 10, 2021 Yeh bolle goggles are my go to . Replace them often too . Hate scratched / grubby goggles Link to comment Share on other sites More sharing options...
sutty2006 Posted September 11, 2021 Share Posted September 11, 2021 I’ve had to weld my D1s chassis in the same place. 2mm thick steel and a high powered welder. Your inner arches look mint in comparison to mine, mine fell out last year between MOTs. Dry stored in my unit too! Link to comment Share on other sites More sharing options...
jakebullet Posted September 15, 2021 Author Share Posted September 15, 2021 Does this look more acceptable? Flap disk'd it, but then out of gas so had to try and improve with stick welder. It's strong enough, so underseal? Wheel arch is only localised, so going to fix smoll hole, and monitor rest of arch. @Minimad5 how clean do I have to get things for buzzweld primer to work? Been at it with the grinder flap disk and power file. Is this good enough? Mostly clean with odd bit of brown Link to comment Share on other sites More sharing options...
Minimad5 Posted September 15, 2021 Share Posted September 15, 2021 27 minutes ago, jakebullet said: Does this look more acceptable? Flap disk'd it, but then out of gas so had to try and improve with stick welder. It's strong enough, so underseal? Wheel arch is only localised, so going to fix smoll hole, and monitor rest of arch. @Minimad5 how clean do I have to get things for buzzweld primer to work? Been at it with the grinder flap disk and power file. Is this good enough? Mostly clean with odd bit of brown Don't use primer Mucka' use some Rust Encapsulator (R.E) which is like red oxide. Then when this goes off you've got a choice of other products to put over the top of this, I like C.I.O (chassis in one) but isn't that hard if you're going to be going off-roading, so something like WAR or the 2k Armour. Link to comment Share on other sites More sharing options...
jakebullet Posted September 15, 2021 Author Share Posted September 15, 2021 4 minutes ago, Minimad5 said: Don't use primer Mucka' use some Rust Encapsulator (R.E) which is like red oxide. Then when this goes off you've got a choice of other products to put over the top of this, I like C.I.O (chassis in one) but isn't that hard if you're going to be going off-roading, so something like WAR or the 2k Armour. I was meaning rust encapsulator when I said primer. Been a long vibratory day. Was thinking 2 coats of that, 2 coats of CIO, then a splash of war. Don't want to be doing this again. CAN RE handle a bit of brown? Link to comment Share on other sites More sharing options...
Minimad5 Posted September 15, 2021 Share Posted September 15, 2021 If you've got a flap disc just give a quick buzz over, I think* aslong as the surface is keyed, not greasy / oily then it should be alright mate. I normally flap disc or use them funny looking ones (I'll add a picture when I find it) .... don't be tempted to use any cleaning sprays such as Brake & Clutch cleaner, as they all leave behind a residue and make it go to pot. These are the discs I mean ... chaseracer 1 Link to comment Share on other sites More sharing options...
Minimad5 Posted September 15, 2021 Share Posted September 15, 2021 Ideally if you're doing the lot : Hot pressure wash the whole chassis - With lots of degreaser (Screwfix do an own brand which is alright) Borrow a leaf blower and dry the lot, then do the whole Angry grinding disc procedure. chaseracer 1 Link to comment Share on other sites More sharing options...
jakebullet Posted September 15, 2021 Author Share Posted September 15, 2021 Don't have a pressure washer I've been needle gunning to knock off the old paint / thick rust then angry grinder. I've got one of those strip & clean disks but can't use it, bloody thing is too thick and the pins of the grinder spanner can't reach the nut ! Link to comment Share on other sites More sharing options...
Scruffy Bodger Posted September 15, 2021 Share Posted September 15, 2021 30 minutes ago, jakebullet said: Don't have a pressure washer I've been needle gunning to knock off the old paint / thick rust then angry grinder. I've got one of those strip & clean disks but can't use it, bloody thing is too thick and the pins of the grinder spanner can't reach the nut ! Don't use the spanner then, just snug it up by hand. The only time I ever use the spanner on a grinder is if it's snagged on something and done itself up tight and I can't undo it by hand. I never, ever tighten up a new disk with one and at times I use grinders an awful lot. Bstardchild 1 Link to comment Share on other sites More sharing options...
Andyrew Posted September 15, 2021 Share Posted September 15, 2021 Same here, i never use the spanner, i can never find it either when i do need it for one thats got stuck!. Link to comment Share on other sites More sharing options...
Minimad5 Posted September 15, 2021 Share Posted September 15, 2021 ^ Just make sure the disc isn't touching the guard, as this can pinch the disc and make it feel & look tight ... then when powered up creates a vibrating death machine 😅 Link to comment Share on other sites More sharing options...
jakebullet Posted September 24, 2021 Author Share Posted September 24, 2021 Disco is a real land rover now! All real ones need the footwells welding up. Took the wing off for better access. Fucksocks. Entertaining welding thinner stuff when my mig only works on top power (130 amp). Bit at top was done by MOT station 2 years ago. Mine doesn't look much worse, and a good wob up will improve it no end. Still got to fix the huge hole. Spent yonks cleaning to avoid fire, there's thick tar on inside, and seam sealer +underseal on the outside. Apart from where the hole is the steel is in good condition. Minimad5 1 Link to comment Share on other sites More sharing options...
jakebullet Posted October 10, 2021 Author Share Posted October 10, 2021 Bored of welding now Fixerated: Only passenger front arch to check now, and the brown bits are finger prod proof so hopefully not moar welding. Scruffy Bodger, LightBulbFun, Minimad5 and 1 other 4 Link to comment Share on other sites More sharing options...
jakebullet Posted October 27, 2021 Author Share Posted October 27, 2021 Guess what? Welding Arse end of passenger sill was a big hole. Shiny: Fixed! Also blasted paint into the sill with an underseal gun and the handy holes in the side & bottom. Hopefully won't rot again. chaseracer, LightBulbFun, Scruffy Bodger and 2 others 5 Link to comment Share on other sites More sharing options...
bezzabsa Posted October 27, 2021 Share Posted October 27, 2021 keeps ya on ya toes.......had way too many LR products and seen how bad they can get. Strangely the older they are the better they are, had an original K plate RR and chassis was rock solid, my RR softdash 96M plate already had a few patches.. at least with a series Landy you only need a hammer, adjustable spanner and a welder to fix 90% of it!! jakebullet 1 Link to comment Share on other sites More sharing options...
jakebullet Posted December 11, 2021 Author Share Posted December 11, 2021 The man from Delmonte he says yes! Mot pass without any advisories. A step up from last years "all chassis & underbody corroding". I did put 4 new tyres on before testing, so maybe that projected a bit of confidence. stuboy, Shite Ron, Andyrew and 3 others 6 Link to comment Share on other sites More sharing options...
twosmoke300 Posted December 12, 2021 Share Posted December 12, 2021 I don’t miss my LR one little bit . Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now