Jump to content

The oldest Land-Rover Series 3 around - new boots arrived


mat_the_cat

Recommended Posts

On 1/5/2023 at 2:14 PM, DeanH said:

Do you have any recommendations for LR forums to keep an eye out on for a reasonably priced rolling project? Ideally early S3 ish.

I've got absolutely no idea, sorry - I'm not part of the LR 'scene'!  I'd guess you'd probably get less chance of a bargain in such circles as everyone is likely to know the value, so anything which really is a bargain will get snapped up straight away.

There's a job I've been meaning to do for a while, but had never got round to it, which was this:

20230106_182559.thumb.jpg.4ddd6d56fca7c94602dd5f5aadf97707.jpg

Rocker cover is dead easy to remove, just 3 screws, and I was pleased that the top end of the engine seemed pretty clean.

20230106_171017.thumb.jpg.04d0eded7800143467adf855fa8bcc6a.jpg

They were mostly slightly wide, with a couple noticeably wider which may explain the faint valve clatter I could hear. Easy to sort, and the rocker cover was replaced with a new gasket. Self-adhesive on one side which made it easier to install.

20230106_174620.thumb.jpg.28f8909130247d6707fc4067bdd9f8d7.jpg

The engine seems a touch quieter, although I now notice the exhaust to manifold joint is chuffing slightly. so another job on the list! Then on to a more minor job. I'd noticed a few holes in the slam panel...

20230106_183001.thumb.jpg.3d09ae7792bcc6db959e8523f96cec4c.jpg

...and a bit of Googling showed I was missing a warning plate - fortunately there's loads of places selling reproductions of seemingly varying quality. The one I bought seemed fine, and the holes lined up perfectly which was satisfying :-)

20230106_183033.thumb.jpg.18716acbdaff8b4d69e73f894545c584.jpg

Link to comment
Share on other sites

  • mat_the_cat changed the title to The oldest Land-Rover Series 3 around - exhaust failure

Trouble is, that won't stop it rotting from the inside out, so I am leaning towards a stainless system. It's patched up for now, so the manifold is the next concern. New ones under £100 so not disastrous, although think I'll fit stainless studs to it to prevent a repeat.

Then a couple of months to decide what to do with the full system, as it feels like it's on the verge of being beyond patching. I really struggle to see how they made it last so badly!

Link to comment
Share on other sites

4 hours ago, mat_the_cat said:

shockingly bad for 2 years and 3k miles!

Probably one of the cheaper pattern ones that aren't anything more than mild steel.  No plating, nothing.  They rot both from the inside out from condensation and from the outside in due to them rusting the moment they're fitted.

A full stainless exhaust was £150 about 20 years ago.  I'd expect that to be nearer £500 these days with inflation and cost of stainless these days.  That said, the one I helped fit 20 years ago is still on the vehicle looking as new as it did 20 years ago, so if you plan to keep the vehicle long-term, it will be the only exhaust you ever buy.

Link to comment
Share on other sites

45 minutes ago, Talbot said:

Probably one of the cheaper pattern ones that aren't anything more than mild steel.  No plating, nothing.

I think you're right. It was visibly rusting after only a couple of weeks, and is so thin it doesn't take much to perforate it. Plus it doesn't even fit all that well - it contacts the chassis occasionally under the seatbox, and sits very close to the rear tyre (although 7.50s don't help).

One of the other manifold studs has sheered clean off, as the diameter had waisted quite significantly. Repair involved lashings of exhaust paste, a stainless nut & bolt, and two jubilee clips...

Link to comment
Share on other sites

I've bitten the bullet and ordered a new stainless system, plus a manifold. New ones were under £100 which was less than I expected, but I found a used one for £55 which already had been fitted with stainless studs. Just waiting for bits to arrive now! With the aid of an old parts diagram I've pieced together the fasteners etc I may need, as all the fitting kits I could find online were only partial kits.

Capture.thumb.JPG.474743831c60c3c15920bff544fb499c.JPG

I'd rather have everything I may need beforehand, given the low cost of the bits and the likelihood of something snapping! I've stopped short of a HG too but have a slight worry that it'll have to come off for drilling out the studs. For future reference the parts list (some numbers have been superseded) is as follows:

Stud 247144 x 2 (top either side of middle)
Stud 564574 x 1 (middle top)
Bolt BH605221L x 4
Bolt BH605161L x 2
Bolt SH605091L x 2
Nut (brass) RTC3629 x 3
Thin washer 587405 x 5
Thick washer WA108051L x 4
Spring washer WM600051L x 11
Clamp 564308 x 2
Manifold to head gasket 274171 x 1
Manifold to manifold gasket 247824 x 1
Lock plates 596490 x 2 (not required IMO if you're using lock washers)

It also seems like there should be a heat shield present, which may have helped with the fuel vapourisation issue last year. I'll either buy or make something up, depending on cost (I'm certainly not paying £80 for a new one!!)

EDIT - thin and thick washers now corrected...

Link to comment
Share on other sites

That parts list could be useful... Dad's in the middle of changing the manifold gasket on his at the moment so if something goes Pingfuckit then I'll forward him your list, though he's pretty much only been able to do one bolt every few days because of his back. 

 

Also, there's no heat shield that I'm aware of, but of course it could just be missing! 

Link to comment
Share on other sites

1 hour ago, Crackers said:

Also, there's no heat shield that I'm aware of, but of course it could just be missing! 

I wonder if it's usually always rusted away? Found an old photo online though.

spacer.png

Given that it only suffered twice last year when the ambient was around 30°C *and* I'd done a lot of low speed work immediately before switching off (=high underbonnet temperatures and less fuel flow), its absence probably isn't a massive problem. Only ~£20  from Dingocroft so may as well though.

https://www.dingocroft.co.uk/acatalog/Heat-Shield-2-25-Petrol-587095.html

If there's any bits that Father @Crackers needs and I've got them left over, happy to stick them in the post.

Link to comment
Share on other sites

This is the bodged manifold, which is attached to the downpipe with one stud, one bolt and a lot of hope! I've packed with paste and held it all in with a jubilee clip.

20230108_162616.thumb.jpg.5fa9ef58b7f8450d7682d6d0ca919815.jpg

My used manifold arrived, and the studs which join it to the inlet manifold were (accurately) described as showing signs of wear, but the seller included a new set of studs. I took that to mean they didn't want to risk shearing one off before selling it! Two came out reasonably easily, but they had necked down quite considerably to I was very wary of snapping them off, especially as the last two appeared at one with the manifold.

20230113_182612.thumb.jpg.a5b8fffd9cdec02e74e03ec50c006ba4.jpg

I could have just left them, but with a packet of new studs in my hand the temptation was too strong. With plenty of heat and gentle persuasion they came out intact...phew!

20230113_190415.thumb.jpg.4baf74acb37cf6047eab885c4d248b5f.jpg

New studs were screwed in with the aid of copper grease, but I'm under no illusion that future removal will still be equally stubborn!

20230113_191659.thumb.jpg.ab8e65b87ffa623f8d3b0836f3d4ec32.jpg

The downpipe studs had already been replaced with stainless, although I've added brass nuts rather than stainless. I've had experience of stainless on stainless fasteners galling before, albeit at higher temperatures than I'd expect on an exhaust, so I'm playing it safe.

20230113_191803.thumb.jpg.a8561fc8fd03abbc3213218b2d3dbeb5.jpg

I only hope that the manifold to head fixings all come out, as I don't really want to be taking the head off (even though it looks to be about as simple as they come).

20230108_162312.thumb.jpg.2929b73b26c2107be680beb6ccdbe096.jpg

The heat shield is now here too, but I'm obviously waiting till the manifold swap to fit it.

20230113_191937.thumb.jpg.aec9e4dd4f88a83a6f25accf6cf9c63c.jpg

One more minor job I've sorted is the seatbelt mountings. I'd assumed these were standard fixings, athough I was concerned they wouldn't be up to much in a crash.

20230111_152351.thumb.jpg.354fc85c25b364ce3eda6e0c0f508bf0.jpg

But @Talbotpointed out the proper mounts were fitted by the B pillar, which is a stronger area, as well as putting the belt in the correct orientation relative to the upper mount. The part number I required was MRC4692, which I found for sale at a mere £220 a pair! I made my own up with a pair of universal plates, at around £3 a side. You can see that the reel is now in a more natural position compared to the other side.

20230111_152327.thumb.jpg.a56067b336f6fc969dd931974d26f9ac.jpg

Lastly a bit of smugness! I've been moving some firewood around on a small trailer, and have fitted a front hitch for maneuverability. Hitching up solo yesterday I was chuffed to get out and find I was 'close enough' at the second attempt :-)

20230111_132220.thumb.jpg.140f9505e20f86ac0227297cd26dacb2.jpg

Link to comment
Share on other sites

As I keep mentioning, I was worried I'd snap another stud, especially this one:

20230115_114221.thumb.jpg.5bd4a116cf14cfe41d7cc5656ad799fc.jpg

But in the end it came undone in a bit of an anticlimactic way! I just gave it a testing tap with a spanner, and it cracked loose straight away. So I figured I may as well start the job. A few minutes later it was all off, and new studs in.

20230115_125946.thumb.jpg.a9bae93507ea766cdb7de70e9605d938.jpg

Then manifold back on, which took a bit of jiggling.

20230115_141659.thumb.jpg.6b902db610aefce1255cf6e215fa52c2.jpg

I could then move on to the exhaust. Quality seems OK, not top notch but better than the old one. That didn't even fit particularly well, as the tailpipe was very close to the rear tyre.

20220322_150139.jpg.7cb9d1233d34b0c26c45ab4b8ade8647.jpg

And the PO had to make up an additional bracket to fit it to the chassis mounts!

20230115_175529.thumb.jpg.fd25deefc4ff306a2c6266bc1c578f4b.jpg

But it still knocked on the chassis on startup and switching off, as I realised when taking the gearbox out.

The new one went on pretty easily, with more clearance all round...

20230115_192955.thumb.jpg.c0a95e9a045941ecaaccc3347660f258.jpg

20230115_193033.thumb.jpg.242d3c814fc04dae608ac4f9a9a28ef1.jpg

20230115_193142.thumb.jpg.dabc5d74cee313591c62d46c29940316.jpg

...and attached to the new manifold.

20230115_193114.thumb.jpg.75d85fde0af7a49a6077b1c77b9f0c63.jpg

Awaiting the first startup, but I need to cut out a new carb gasket, and I've come inside to warm up!

Link to comment
Share on other sites

Last night I finished the job, including the fitment of the heat shield. I'm not sure how effective it'll be, but we'll see...

20230116_011014.thumb.jpg.67342df85de532fb1ad1a9386e5ccf97.jpg

Time to fire it up, and check for leaks.

Oh. Aside from the engine sounding rather clattery on video, the new exhaust does sound different, in real life too. Gone is that A Series-esque fruity rasp, to be replaced by a deeper tone. I'm not immediately taken with it, but will wait to see what it's like whilst driving, if I can hear it at all over the wind noise. There does seem to be a bit of resonance at idle, which disappears when you raise the revs.

 

Link to comment
Share on other sites

No difference in performance, or noise behind the wheel TBH. It was put to use in the sunshine this morning shifting a small trailer.

20230117_110834.thumb.jpg.e0ef09e849befd6d33024c7c8374fea2.jpg

But then we got a dusting of the white stuff!

20230117_194624.thumb.jpg.67feef115cf2a00825dd8b3ba018fca3.jpg

And for a change it was actually cold enough for it to settle, a few heavy flurries too.

I didnt think it was that bad, but I got back home to find the road had been closed. I guess the fresh snow is fine, but it'll be a different story once compacted down and turned to ice.

Link to comment
Share on other sites

  • 2 weeks later...

I've had a birthday recently, and got some alpine windows for this as a present :-) Something I'd been thinking about but never bitten the bullet.

Trouble is, I've now got to cut two holes in the roof! And I'm not sure exactly where. To me, the position they are in on an 88" Series doesn't look quite right:

img_2107.800x600.jpeg.8ede8f4ac79b6dd49ecd70f1e88bd3bd.jpeg

ydu.jpg.524be7b53476588e10722da3c2013c72.jpg

On a 90" Defender, they look better to my eyes:

1I4A8312.thumb.jpg.995b012550e18268c265a1b928ec3405.jpg

326457bb39638b2178a312c62e4de840_429462.jpg.4226f24ee1150f58ce2852d52ac235c6.jpg

So I could just go for where looks right. But then if I ever decide to get a headlining, it will probably mean they're in the wrong place! I probably won't (as they're a lot of money), but I just don't want to regret it later...

Is it just me? Do the 90s look better positioned?

The other thing which is on the cards at the moment is the rear diff. Having a quieter gearbox does highlight the fact that it is a bit rumbly, especially on the overrun. It certainly doesn't give the feeling that it's about to explode any minute, but is mildly concerning (and yes, there is oil in it even though there's none leaking out!)

Link to comment
Share on other sites

  • mat_the_cat changed the title to The oldest Land-Rover Series 3 around - cutting holes in the roof!
On 1/27/2023 at 6:43 AM, twosmoke300 said:

Or where it fits between strengthening spars maybe ?

Give that man a doughnut! Hopefully I'd have had the foresight to check before actually cutting, but I wouldn't have put it past me to make an expensive mistake :oops:

I'd made made up my mind I wasn't keen on the standard 88" position - it might be the 'correct' way to do it but I'm not doing this for resale value, just how I want it. However it looks like the 90" position will cut into a support strut, which stops me centring it perfectly on the lower window. But I think I can still locate it so it looks better...

Link to comment
Share on other sites

On 1/6/2023 at 8:17 PM, mat_the_cat said:

I've got absolutely no idea, sorry - I'm not part of the LR 'scene'!  I'd guess you'd probably get less chance of a bargain in such circles as everyone is likely to know the value, so anything which really is a bargain will get snapped up straight away.

There's a job I've been meaning to do for a while, but had never got round to it, which was this:

20230106_182559.thumb.jpg.4ddd6d56fca7c94602dd5f5aadf97707.jpg

Rocker cover is dead easy to remove, just 3 screws, and I was pleased that the top end of the engine seemed pretty clean.

20230106_171017.thumb.jpg.04d0eded7800143467adf855fa8bcc6a.jpg

They were mostly slightly wide, with a couple noticeably wider which may explain the faint valve clatter I could hear. Easy to sort, and the rocker cover was replaced with a new gasket. Self-adhesive on one side which made it easier to install.

20230106_174620.thumb.jpg.28f8909130247d6707fc4067bdd9f8d7.jpg

The engine seems a touch quieter, although I now notice the exhaust to manifold joint is chuffing slightly. so another job on the list! Then on to a more minor job. I'd noticed a few holes in the slam panel...

20230106_183001.thumb.jpg.3d09ae7792bcc6db959e8523f96cec4c.jpg

...and a bit of Googling showed I was missing a warning plate - fortunately there's loads of places selling reproductions of seemingly varying quality. The one I bought seemed fine, and the holes lined up perfectly which was satisfying :-)

20230106_183033.thumb.jpg.18716acbdaff8b4d69e73f894545c584.jpg

Anyone else find it hilarious but not in the slightest bit surprising that there’s a warning about welding the vehicle? 😆 

Link to comment
Share on other sites

I didn't fancy moving the roof strut, as it was spot welded to the roof. So I decided to line up the alpine window with the rear edge of the lower window. All marked out 4mm larger than the glass:

20230131_164308.thumb.jpg.72462e24f59afcadb371e849ef5bd7a9.jpg

No going back now!

20230131_172457.thumb.jpg.4cb085746a1776fc7641d926304f0112.jpg

With a fair bit of force and soapy water I got the glass into the seal, then it was a case of fitting the locking strip into the seal. I've done these before with just a screwdriver and thumb, but this time have bought the proper tool.

20230201_000504.thumb.jpg.19d405cadec19405beb04c9b9497ee46.jpg

You have a loop which teases open the slot in the seal, then a roller which pushes the strip into the slot. Much easier, although the ends were still tricky!

First side took around an hour to fit to the hole, and I'll hopefully do the other side tomorrow (actually today). But pleased with the way it looks.

20230201_003716.thumb.jpg.9449dd545371fc370d82986c079387c5.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...