Jump to content

The Current Driveway...


TrabbieRonnie

Recommended Posts

Bit more work done on the jeep.  

New thermostat fitted (tested in kitchen first!), and after a bit of faff bleeding the system, running lovely.  I'm going to run it for a week and then drop the coolant again.  Parts of the system were a bit crusty for my liking, so I'm treating this as a flush.

We then set to the re-oiling of the underside.  Not a nice job, but kind of vital in this neck of the woods.  My youngest and I spent the day blinking out/spitting out rust, but got the bottom wirebrushed nicely...

IMG_20220910_171628_317.thumb.jpg.4efaac1d12ae9b3336d2336b181647d4.jpg

It was nowhere near as bad a job as the big de-rust a couple of years ago (documented on this very thread), but still took the two of us a good few hours.

Cooked up an oily brew this morning, and am just back in...

IMG_20220911_110114_535.thumb.jpg.ddbc32ee70d77626bfe013ea0bbc4e77.jpg

Much better.  It's a very oily mix this time, probably one litre of waxoyl to two of used engine and gearbox oil.  It stinks, but creeps well if applied hot, and never dries out.  I'll have to do it every summer from now on, not leave it too long.

IMG_20220911_110129_461.thumb.jpg.3f10b09bf0a1fb26839e04bef9931f54.jpg

IMG_20220911_110211_009.thumb.jpg.9dea3034b0bcdf61b053a2aa4c0985df.jpg

Interior still looking good on its years too...

IMG_20220911_110247_016.thumb.jpg.6632ab0fbf8dd26a5945ab8fe96be2ed.jpg

IMG_20220911_110317_081.thumb.jpg.15e5d6cd9dab4d7f500b336c9cd2b4de.jpg

Just the sills/bumpers to paint up, then she can battle through another salty Moray winter.

 

Link to comment
Share on other sites

  • 3 weeks later...

Hi all, 

I have been lurking and not posting for a wee while (new job keeping me busy), but further work on the jeep has happened...

Once back on the road, some clicking from the rear wheels could be heard.  This quickly developed into a rumble at speed...  With all new rear brakes fitted recently, the wheel bearings were suspected, and yeah... our winter drifting shenanigans may have taken their toll...!

Pretty fubarred.  A mere 70 gbp's were required for a set of FAG's finest from Roughtrax, and this weekend saw the fitment commence.

Phase one is the removal of the four nuts that hold the hub into the axle end, the damper needed to be disconnected  at the bottom to allow access.  These four 14mm nuts were now identifying as 13.3mm thanks to 30 years of rusty time, and so much hammering and swearing was required to free them.  However, freed they were, and with the brake line and handbrake cable out the way, out comes the halfshaft/hub assembly...

Good times.

I do not have a press at home, and did not fancy the 'bush mechanic' method of swinging the whole thing around like Thor's hammer into a block of wood to shock the bearing out.  I therefore employed the method I use at work, grinding a slot into the inner race, splitting this with a cold cut, and breaking the bearing up somehow.  Not pretty, but it worked...

We were videoing/photographing all this for my youngest's benefit btw, he is on his first year of a mechanical engineering course at college and wants to document all these missions now.

Refitting was simply tapping in the new bearings and seals and putting it all back together.  The brake lines were buggered in the disconnecting (they never just undo, do they?!), and so I broke out the flaring kit and made up some new ones...

IMG-20221002-WA0000.thumb.jpg.c32ac8d22144e67e23861c534cc2d5d8.jpg

Included was a replacement Flexi and hard line to the bias valve at the top, VERY satisfying.  

To celebrate, we threw the bikes in the back and headed for the trails.

IMG_20221002_180646_859.thumb.jpg.b315485404954d0754a709a39dbc0213.jpg

Job jobbed.  Hopefully we are now done for the winter (mot is in January), wanted all the underside work complete before the weather comes in.

 

Cheers all.

Link to comment
Share on other sites

  • 2 weeks later...

Hi all...

Hope all's well out in the shiteyverse, I haven't been on much, and there's not much to report from Trabi Towers either.

As I mentioned, I have changed jobs (back on the tools installing grain handling equipment (distillery and malting gear as befits the local industry)), which has left me with more time, less stress, but more physically knackered! 

As such, the cars have been neglected a wee bit.  A small coolant leak appeared from a porous radiator hose on the 323, now replaced with universal wire-wound stuff.  Apart from that, it's cruising along beautifully.

The jeep is also rolling along fine on its new wheel bearings.  We even found a wee abandoned quarry up in the woods to test on the old girl...

IMG-20221015-WA0004.thumb.jpg.7a9c20ceecad32c4b8a12ad2121ebf10.jpg

IMG-20221015-WA0006.thumb.jpg.d03be253ed319bfef23a13b9b1dcb51b.jpg

IMG-20221015-WA0013.thumb.jpg.6c588a85340f7bc017a5be5b5209cd36.jpg

And yes, she now requires a new rear fog light... she did get up that hill though, in fact it was even easier the second time once I remembered I had low range to play with.  Ballpoint rubbers look past their best, so will get them done before the test methinks.

The RX8 is still in the 'thinking about it' category; after the initial bit of welding she now just gets run up every few weekends to annoy the neighbours check the engine still braaps...

It seems to be ok.

Junior is prepping the wheels for paint, going for gold again (I want to keep the gold stripe down the side too).  I'm in no rush with this one though, as long as I can hit the NC500 in it next summer I'll be happy!

The Coupe has been temporarily moved to my in-laws, the new job comes with a mahoosive van (very handily stacked with gear, and someone else pays for the motion lotion too), meaning I have officially run out of room.  It will be sold when I can get around to it, my hand is definitely being forced now!

 

That's it I think, cheers all!

 

Link to comment
Share on other sites

I neglected to summarise the big Audi's condition, the A8 for sale thread reminded me though...

For a wee while now, it has been telling me that the battery level is low.  It communicates such things to you via the screen in the dash, and the binnacle.  If you ignore these warnings, it starts to turn things off, in my case the central locking.  Annoying, but not urgent as I've hardly used it anyway since starting the new job.

So, a trip to Halfords ensued this weekend past to purchase the biggest battery I ever have, a 900 CCA monster!  Sticker price of £142 came down to £115 with the old Trade Card, but still ouched.

I intend to fit it this weekend.  It of course requires VCDS-ing, to tell the car exactly what type and size has been installed, and a slave battery must be connected first, so that it is never without at least some amps.  Fun.

Second job (been bugging me for a while), was the serpentine belt.  The old one...

IMG_20221018_174136_971.thumb.jpg.f9f989538e93d73f6e7ec954fc1ed464.jpg

IMG_20221018_174124_904.thumb.jpg.5c9a8093774c2bb33132197def43a1b8.jpg

Yeah, not good. 

And yes, I should have splurged on new tensioners/idlers I know, but didn't ok?!  I have just fitted the new gates jobbie tonight...

IMG_20221018_170458_247.thumb.jpg.685eb166a69e09c2f4798d1e408cbbd9.jpg

Tensioners felt fine 🤞

My arms are scraped raw, my patience has left the building, but it is on.  They will tell you the front of the car needs to come off for this one, but no, it can be done without.  The belt is, 2.5 metres long, and truly serpent-like, 'orrible.

Link to comment
Share on other sites

  • 2 months later...

Hi all...

Seasonal greetings etc.

 

Surf plodding through the weather beautifully, here's me and it attending to a neighbour's stricken XC70, the gearbox of which has decided to lose the plot exactly when it's AWD qualities would have been handy...

IMG-20221218-WA0001.jpg.488514e92acc146d72353499faf23470.jpg

She should have bought a Toyota, I know...

 

Been out for a run in the Trabi today, as for some reason I keep forgetting to SORN it.  Thought I may as well enjoy this month's £21, so went to the beach for a refreshing stroll.  Mazda came too...

1556241493_IMG_20221229_142628_3022.thumb.jpg.c79033a2f02825cb83dd9416bc782607.jpg

Both are running well, Mazda is faster on the straights but not through the bends! 

We replaced the dizzy cap/rotor arm/leads on the 323 a few weeks back, after the slight 2500 rpm flat spot she'd always had when cold became permanent, and accompanied by longer start times.  Both problems have vanished, and the new-to-us motor is silky smooth once more.

Rosie the Trabi just buzzes along like always to be honest.  So little to go wrong.  Washer jets (manually operated) were a wee bit pathetic, so that's something to tweak I guess...  'Big Car' has just done a Trabant history on the 'tube, which was nice.

 

Big Audi has borked, losing a suspension level sensor to corrosion in the connector plug.  This after having just passed the mot lovely as well. 

At first I only suspected the sensor itself, and so bought a set off eBay.  However, on removal half the rotten pins remained in the car's half of the plug... bugger.  Someone had replaced this before, the wiring has been spliced (nicely, tbf), using a plug off another model with different wire colours. 

Anyway, I have ordered a repair kit consisting of new plugs and the wee pins, enough for both sides.  Despatched apparently, see if they get here while I'm still off work...  On their arrival, I'll fix that and service the big lump, as it has started shouting about that also.

385743399_IMG_20211128_102315_7262.thumb.jpg.165af5d181505706ee77ca85c51544e1.jpg

It seems happier with the plug disconnected altogether, the air suspension was NOT happy with the weird readings it was recieving when the sensor failed.  Of course, it happened when my wife was driving home, at night, in a blizzard.  The front end was bouncing up and down "like one of those Mexican cars" apparently, with the fancy xenons doing their best to alternately blind all oncoming traffic, or illuminate a patch of road about six feet off the front bumper. 

Vorsprung Durch Technic indeed.

 

Had Christmas up at the outlaw's place, so spent the meal looking longingly out the window at the Audi Coupe currently stashed there. 

received_754985572438559.thumb.jpeg.a8bb4ee0ed39153f2013e1455f1a3535.jpeg

Must sell it or something else back here at the ranch to make room. 

New year's resolution maybe...?

 

Link to comment
Share on other sites

  • 1 month later...

Hi all.

Well, Big Audi refuses to speak to the new level sensor I fitted... not sure if it's because it's a non-genuine part, or I have buggered up the wiring of the fiddly wee pins in the multiplug.  Further investigation required, however, the car is behaving a lot better.  All suspension heights are selectable, it's just that the headlights stay set too low.

It has also developed an exhaust leak at the flexi I damaged a while back (gave that job to the garage to sort, will have a look myself this time).  It sounds amazing (think American V8 burble), but is a bit anti-social.  It's all stainless, so hopefully the flexi bit has just come loose or something.  Would have had a look today, but it snowed overnight...

 

Mazda 323 has had more stickerage applied, and therefore an extra 5hp at least...

81473237_IMG_20230218_134538_4362.thumb.jpg.702b2ce61c3ca921e8d4408f051dbce1.jpg

We're thinking of getting a wee boot spoiler for it too, like the GTR version. The wheels and sunstrip are giving it quite a sporty vibe, which I think suits it...

IMG-20221015-WA0030.thumb.jpg.0305b2acf6273ac397d676520480ec5d.jpg

Had a wee taz round the local area this morning, below was a refuel stop for the Trabi, hence the bonnet up...  (Trabants, as we know, never FTP).

IMG-20230218-WA0004.thumb.jpg.57ecee173b21c8361d68124712146472.jpg

I fill my jerry can (in the boot) at the petrol station, and then mix in the 2 stroke oil in that before filling the car's tank.  This ensures a good mix of the right proportions.  Also saves funny looks on the forecourt as you lift the bonnet to fill her up!

Really looking forward to the summer now, should be fun with the RX8 if I can get it sorted too.

Cheers now.

 

 

 

 

Link to comment
Share on other sites

  • 3 weeks later...
  • 1 month later...

Long time without an update, must try harder!

Currently on the isle of Lewis (outer Hebrides), and finding swooping along in the A8 V8 very agreeable...  The roads are a good mix of wide open/see for miles, and twisty single-trackers.

IMG_20230419_093708_143.thumb.jpg.09c3fd9cfe4311fa8ec5e5a7dd706986.jpg

I have been here once before, but headed south to Harris, and then to Barra.  Some bits here feel like another planet, very beautiful and helped by the glorious weather...

IMG_20230419_101352_657.thumb.jpg.37ffac18bfd50592bd2d2e100bdd16f9.jpg

The car feels perfect here, and is running well.  I got the new exhaust flexi in a wee while back.  The rather ample rear took all the luggage (including two guitars, amps etc), easily, and the power available means you just flow up the hills without effort (some effort must be being made somewhere however, as we're currently showing 25.7 mpg's!)

Back on the boat at the weekend, the drive across country between Ullapool and Inverness is a good one too.

Cheers all.

Link to comment
Share on other sites

  • 1 month later...

Hi all, 

More island travels have been had, this time with work, but enjoyable nonetheless...

IMG_20230523_152334_468.thumb.jpg.20dd99b0e5c61047cfdda1f3aa4ca399.jpg

Lovely place and people, and the road out towards Mull... stunning!

Anyway, on my return we fitted 5mm spacers to the Audi Coupe, mainly to impress my boys tbh.  They have made a very subtle difference, but the car looks bob on I think...

Before...

IMG-20230515-WA0017.thumb.jpg.4d80e6ffef37fc723805fc1ebf72122b.jpg

And after.  Like I say, subtle but looks great in the real life...

IMG-20230527-WA0002.thumb.jpg.085b804b16f36ebe179ca91a83c071d3.jpg

IMG-20230527-WA0008.thumb.jpg.f194c1a785d186d300cedf0ecf0818db.jpg

803633497_IMG-20230527-WA00012.thumb.jpg.f54a8b6eed1aad00ae4f397fa205eb5d.jpg

The wee car is driving lovely, currently very glad I didn't sell it!  We recently bought a box of 80s/90's albums on cassette, as this, the jeep and the 323 are all blessed with a tape deck.  

I will have the cash one day for a respray, just going to enjoy it's slightly scruffy Audiness till then.

 

Trabbi also buzzing along nicely, having just passed its MOT without advisory.  I've started touching up minor bits of body paint, and have redone the wheels, so she's looking pretty smart.  I'm considering removing and cleaning out the exhaust (fairly sure we used to fill 'em with caustic soda when I were a lad?), Certainly the tailpipe end is fairly gunked up after the few years it's been on, so god knows how the centre resonator/silencer is inside.  Any and all advice on the best way will be appreciated (stainless exhaust btw).  Stock photo...

IMG-20230319-WA0003.thumb.jpg.65aa95116f3bc1e43d86cd2b4ef219db.jpg

Wee Maz racking up the miles with my eldest, and running at just shy of 50 mpg on the new Demio lump.  He now wants spacers too!

T'other Mazda hasn't had much time spent on it, but I do have a two week break coming up which will remedy that.  My youngest has taken on the wheels in the meantime, and we have settled on some Ford bronzey-browny goodness...

IMG-20230515-WA0000.thumb.jpg.c7b3d5a36fca4f6536654e02eda4d39c.jpg

IMG-20230515-WA0004.thumb.jpg.30e56623eea928ee8e3650a3b042651b.jpg

Nebulous plans to take this thing Autotesting are developing, there is a local club I've found organising such things...  As it stands, the engine is starting better hot, and running beautifully during its regular neighbour-annoying (but very motivating) fire-ups!

 

All in all, much enjoyment has been had with the sun shining on the old fleet, thankfully we enjoy the work as much as the driving about in them!

Cheers all.

 

Link to comment
Share on other sites

  • 2 weeks later...

Actual progress on the RX8!

Hello all, blessed with wall to wall sunshine as we are this week, I decided to get welding today, and have completed one side of the boot floor/wheel arch repairs...

IMG_20230610_143856_373.thumb.jpg.b629a279a55c1efe697a4c569d7ec9e6.jpg

IMG_20230610_143918_042.thumb.jpg.baa52bd6a3172a086cf7100263e7abe8.jpg

Not pretty, but by god it's thin stuff...  lowered my expectations a wee bit, as I just want the thing going now!

Vactan helps...

IMG_20230610_160911_476.thumb.jpg.f6f16bf8eb5afc842ef38ae31a6a8cb4.jpg

IMG_20230610_160944_819.thumb.jpg.b004de8ec935038009e5869dab8da505.jpg

Even had a go at the wheel arch lip, so after I get it oiled up in the wheel well tomorrow that's a whole corner done at least...

IMG_20230610_173730_373.thumb.jpg.86b64dce033a8519ab40f3d627acf0a6.jpg

IMG_20230610_180958_486.thumb.jpg.77893c9b79797dcef7d89c53b5322969.jpg

Inching closer to terrorising the Highlands!  

Link to comment
Share on other sites

About your Trabbie exhaust - I don't know if it can be dismantled the same way, but the old CZ owner's manual used to describe taking the silencer apart, to (paraphrasing, cos I can't remember the exact words) take it out to the back yard, douse it in petrol and set light to it! 

Link to comment
Share on other sites

24 minutes ago, CreepingJesus said:

About your Trabbie exhaust - I don't know if it can be dismantled the same way, but the old CZ owner's manual used to describe taking the silencer apart, to (paraphrasing, cos I can't remember the exact words) take it out to the back yard, douse it in petrol and set light to it! 

If I remember correctly, I have heard of this on old 2 stroke Saabs too?

Link to comment
Share on other sites

I believe so, it would've been common practice probably in the past, given that the gunk in a stroker exhaust is half dried out oil. Burn it up, and it cracks off easily in chunks. Caustic soda dissolves it, so it can be scraped off, but either way works. 

Come to think of it, oven cleaner out of a pound shop is probably cheaper than a half litre of petrol these days, so it might make economic sense!

Link to comment
Share on other sites

T'other side...

IMG_20230617_153844_626.thumb.jpg.28b47dfd30c8c572ebca00ca5ef81389.jpg

Big 'oles in RX8's used to worry me, but no more!  The wet rag hanging to the side is my fire blanket, covering the fuel intake pipe.

IMG_20230617_153908_782.thumb.jpg.3bfe9785f195f38016c81375727d5089.jpg

Decided on a different tack this time, after seeing how the card templates curved into shape...

IMG_20230617_160457_459.thumb.jpg.461b4490a8e4582c8303574d17dccd86.jpg

Left one piece long on purpose, so I could get a nice join between the two bits...

IMG_20230617_160515_091.thumb.jpg.cfefec8b69d7dfc6293e4f5ec9313ce8.jpg

Before tacking it on the outside and cutting off the excess in the boot...

IMG_20230617_161142_110.thumb.jpg.6a85e4745a5f6f18cbb5e7995c9334cb.jpg

IMG_20230617_183419_382.thumb.jpg.f8eb31e6a174c7a6a99c78442c16961c.jpg

A wee bit was then cut to replace a bit of floor.  Again, not pretty, but nice and solid.  I'm sure it'll look ok after a dressing with the flap wheel and some sort of paint covering.  The wooden blocks are used to deflect the grinder sparks, I'm paranoid about them setting light to the back seat foam.

Here's a pic of the welder I bought a few years back.  I can't remember it's specs now, but I remember thinking it was the best power range and duty cycle I'd seen on 240v.

IMG_20230617_170721_866.thumb.jpg.083eb6a4d66f322f8f4e5247b1fce181.jpg

It's a SAF mig, French I think, and is operating on its lowest settings for both current and wire speed in order to not blow holes in the Maz (I still manage the odd one!).  I bought it from a chap who's son was selling up a failed garage business in Aberdeen, for £450.  Seemed expensive, but puts down beautiful smooth welds on thicker stuff, and to be fair, I'm the weakest link on this project I think!

Tomorrow then should see some vactan/waxoyl application, and maybe even the back end rebuilt.  I've cleaned up the crash bar and back bumper, it'll be good to see it look like a car again!

Whilst I was welding, the boys serviced the other Mazda, which is really racking up some miles in my eldest's hands as his gig-mobile.  The boot is always full of guitars and amps, and the tape deck blasting out 90's rock!  A great old age being had by the 323, which has just sailed through the test again.  Somehow, he's done 11,000 on the 'new' engine, which went in almost a year to the day ago.

Just love shite cars.

 

Link to comment
Share on other sites

Well, a very productive day today on the Maz...

received_942006233700381.thumb.jpeg.bba488c296dda2abe034945d9b90cb41.jpeg

Patches look better all oiled up and with the original cable grommets fitted through.  Once I'd refitted the arch liners all of this was covered up anyway, but we'll know it was done right at least!

Wire brushed and Denso-taped the fuel filler pipe to stop it getting any worse also...

received_1383041855612636.thumb.jpeg.9b876c46dbed57ddc2ebce9b09740a0f.jpeg

'Sorted' the wheel arch lip on this side too, they're pretty filler heavy tbh, and will need actually fixing one day!  The plan is to see how the car goes this summer, just enjoy it, and see if it warrants the full job after that.  

IMG_20230624_220032_625.thumb.jpg.86c0b6c2bcf23a2b42a5ea519e3a0850.jpg

After a lot of wire brushing/wheeling, vactanning and oiling, it's really good to see the rear reassembled.

Forgot what a big bum it had...

IMG_20230624_220015_685.thumb.jpg.7be3b02ae5a1952d5ad2880fff7af64f.jpg

Much more still to do.  I now have a catalytic converter in my possession (eBay job, but good reviews...  type approved if that means anything at all?) ready for fitment.  I want to fill the tank with plain fuel to dilute the two-stroke oil down for the emissions test, I don't think the new cat would like the current mix much!

The front wings need rubbing down or replacing, at least they are bolt-ons.  The front lamps came up nice with the old 2000 grit and polish, will post some more pics when I get her washed up a bit.

Cheers all.

Link to comment
Share on other sites

Washed up a bit, and a clandestine run to start running the fresh fuel through.  Will do so every night this week, and then fit the new cat and change the oil at the weekend I think...

IMG_20230626_214850_832.thumb.jpg.7a471036fa68bd0dc9ac04e65a010ed3.jpg

It's funny, there's about seven different shades (and textures!) of blue paint on this car, blebs and wee dents everywhere you look, but somehow it still looks the part!

IMG_20230626_214906_664.thumb.jpg.8a4b405398dff82a8b2e35f110f7881e.jpg

Starting to feel more like one of the fleet now, running and driving well.  Need to get under the front-to-mid section of the floorpan, to see what else is lurking under the underseal.  

The best paint on it...

IMG_20230626_214924_715.thumb.jpg.b04d60ab06777b21744f97f84b06aa03.jpg

Checked the lights (it has very aggressive headlight washers also!) and found a new problem.  The reverse lamps are permanently on.  Switch problems quite common apparently, will have a look in there when next underneath.

Need to get a wriggle on, home this week then away for two with work, followed by two weeks off.  I would very much like some highland road blasts during my time off!

My neighbour rather unkindly proclaimed this as my mid-life crisis car...  he's right I think!

 

 

Link to comment
Share on other sites

  • 3 weeks later...

Well, had a weekend back on the RX8 after a fortnight away with work (replacing two grain elevators at the picturesque* Strathclyde Distillery in downtown The Gorbals)...

We have replaced the fake cat with a real one, which has instantly improved the smell...  It was quite eye-watering before, and now isn't.  

The right hand sill has been gently wire-brushed and re-coated, and the final hole has been cut to allow the rear abs sensor wire through into the boot.  Reconnected, and the abs and traction control warning lights have gone out.

Next came the oil.  The sump plug was the tightest I have ever known, as was the oil filter.  It's removal left us both a bit worse for wear...

IMG_20230716_221254_295.thumb.jpg.2ff53c8a6b30163071cc15f671f86804.jpg

IMG_20230716_221245_900.thumb.jpg.3b83b5a83d53a8745a51bc8e33e55d3f.jpg

T'was an absolute bastard.

Anyway, a few litres of Halfords finest resulted in instant oil pressure on startup, and very smooth running.  Methinks it may have been overdue a change, so I'll probably do it again pretty soon.

The next step in the plan is to subject the nearside sill to the same treatment, another  good wash and interior clean, and then book her in for the test.  If she passes, then her reward will be a new set of tyres for the rear, and either a good used set of front wings or yet more lashings of filler in these ones.

All in all, I'm at the stage I really love when bringing back an old car, when they start to feel a bit more up together, and a bit more 'mine'.  Every time I take it up the lane for a spin, it feels smoother, with brilliant brakes too.

IMG-20230716-WA0010.thumb.jpg.0a130f457bf5927fa08e6c5e68db0183.jpg

Fingers crossed she gets back on the road this week!

 

Link to comment
Share on other sites

Countdown commenced...  Test booked for Friday afternoon 🤞.  It's £30 for a days insurance, or £200ish for the year.  Probably going to just pay for the day in case it fails, and swap it for the jeep on the multicar policy if it passes.

Very excited here at Trabbi Towers, the wee thing is as polished up as a rusty old Mazda can be.  It is driving beautifully up the lane, I can't wait to head out on the open road. 

It's the sportiest car I've had I think, the speed and way it pulls from second into third gear is just... wow!  Still pretty loud even with the cat fitted, but deeper and not at all unpleasant.

The interior has come up nice, and everything works.  Tried the in-dash cd changer this morning, the stereo system is Bose, and almost as good as the A8's.

So I'm basically like a kid waiting for Christmas, I hope the old car gods are kind.

1107710359_IMG-20230716-WA00032.thumb.jpg.0207b8ba478ef49aeb38f0e476e9377d.jpg

 

Link to comment
Share on other sites

It's only gone and passed!!!

Advisory for the rear tyres as expected, emissions didn't look great at first, but fell into line great after a wee rev up... result.

He was more than happy with the underside, and did have a good old prod, so I have full confidence now.  

Tyres should be in for the middle of next week, better burn these ones up in the meantime I suppose!

Spends so far on this one aren't bad, I think I'll be up to the grand mark with the tyres and mot.  

 

Cheers all.

Link to comment
Share on other sites

Second tank of fuel has gone in, teething troubles so far...

Coolant...

Not really a trouble as such.  Coolant level sensors are a notorious fail on these apparently.  It comes on at randomn intervals for the first few miles of a journey, and then again when parking up.  Of course I topped it up a couple of times, leading to it burping it out the overflow on shutdown.  It doesn't help that the 'max' level is very low down on the header tank, it must expand more in this than other cars.  Getting used to it.

Brakes...

Rear left was binding, wheel was hot, covered in dust and started squealing.  Just in from cleaning it all up and pumping some fluid through.  All better, the car actually feels freer so hopefully the fuel economy will be amazing* now!  Zeroed the trip on fill up, so will have an accurate measure next time.  I think the handbrake mechanism might have been seizing up a bit/not quite releasing, as it was all quite rusty looking.

 

And that's it for now.  I am still getting a feel for the car, using the full performance needs a good empty road, but it is a very enjoyable and great handling car at any speed.  New rear tyres on Wednesday I think, which will inspire more confidence also.

Found a fwend at Halfords while in getting gearbox and diff oil...

IMG-20230724-WA0000.thumb.jpg.4d45aad664c333ec9205eafe76cc0354.jpg

Link to comment
Share on other sites

Old RX8 in FTP shocker...!

Suppose it had to happen, and it could have been worse.  Been properly out and about in the car today, out to Inverness and back, and then out to the coast at Roseisle.  A good hundred and fifty or so miles of enjoyable motoring was had.

I decided to stop in at the garage on the way home to check if my new tyres were going to be in tomorrow.  On leaving, the car just went 'click' instead of 'vroom'... bugger.  Starter or its solenoid seems to be the culprit, everything lights up as normal, just no crank.  Gave the offending article a good whack with the persuader, rocked her back and forth, but to no avail.

Couldn't have happened in a better place at least, I must have started the car a dozen times today without issue, weird.  Two days and £170 for the starter, £160 in tyres too, so the cheap rotary experiment is getting less cheap I guess... not too bad though.

 

Fuel costs...

Before all this, all these miles meant that another fill up was on the cards today also, and with the maths done, the mpg figure is...

20.2

(218 miles for 49 litres/10.7-ish gallons).

Not exactly sipping the old go-juice there!  However, for the first quarter of that tank, the rear brake was stuck on, so I should see a slightly better figure for the next one.  I think that figure is about par for the course with these things though... doesn't have to be my daily thankfully!

 

 

Link to comment
Share on other sites

Thankfully, even with the RX8 away in dry dock, Rosie the Trabbi was around to provide mechanical tinkering time today.

Coming home in said vehicle last weekend, the heat exchanger/expansion chamber section of the exhaust split neatly in two, right at the engine manifold joint.  This occurred at full chat, flying up the hill at 60mph.  Without any noticeable drop in performance, my wee 600cc machine gave a passable impression of a Lancaster Bomber on final approach to the village.

Sub optimal, as we are entered into a 145 mile rally around these parts on Saturday, amongst some fine old cars from the local car club.  They have us starting fifth, with all the wee Austin's etc, obviously they are labouring under the false impression that a Trabant is a slow vehicle! 

It is my mission that the hordes of MK2 Escorts and Lotus Elans will be left in our smoky wake, aghast at the speed of the DDR's finest!  Hence, repairs were needed...

My youngest shiter has today dismantled the exhaust, and stick-welded it back together beautifully.  It's a stainless system that has been on for a few years now, and the heat cycles combined with the somewhat intense vibrations must've done for it.  My work van provided some stainless rods so it should last a while. 

We managed to get a more natural fit under the car this time, all the hangers are attached, and none seem to be under duress.

A quick rattle around the local hills has proven the effectiveness of the repair, so a quick wash and scrub up tomorrow and she'll be ready.  I've never done one of these rallies before, it was the promise of a wee rally plate to stick on the front that clinched it!

Next update should be on Friday, with the RX8 hopefully home and happy again.

 

Cheers all.

 

Link to comment
Share on other sites

Rosie the Trabbi has outdone herself today, completing the Tour of Speyside rally in fine style.

Here's us at the start...

IMG-20230729-WA0013.thumb.jpg.dc64791cf0eb0d32284039b7e827180a.jpg

We headed off at 10:00am, my youngest in charge of navigating using the provided map and rally style pictograms.  He was an absolute natural and kept us right for the 147 miles.  I've lived here for years, but still encountered roads I'd never been down before.  Great stuff.

Check out the metal crammed into the Carrbridge hotel's car park, the halfway/lunch stop...

IMG-20230729-WA0016.thumb.jpg.5909d88a8f6948f85cfcc41be334bae1.jpg

IMG-20230729-WA0017.thumb.jpg.78ba680beceab7291834c5a240b61328.jpg

IMG-20230729-WA0007.thumb.jpg.41fb4a2c44de1a82102056d92271e437.jpg

IMG-20230729-WA0019.thumb.jpg.4ee9065d23bfd076f18d36dd0f958f01.jpg

IMG-20230729-WA0005.thumb.jpg.b297a71e2066ef0d6e1251491b38d4ca.jpg

Checked and topped up fuel at this point (11 litres used, very hilly route though).  All other systems checked out fine too, the exhaust repair was holding strong.  

Had a good chat with the owner of a Gilbern Invader, who had been surprised by the Trabbi's turn of speed on the narrow twisties.  He found it especially hard to believe upon seeing the wee beastie's powerplant!

To give a flavour of the relaxing* ambience you could experience during a highland tour in a Trabant, see this video of us hassling some old Escorts and a Lotus around Lochindorb...

 

img_1_1690665459428.jpg.15cb77ed7e766ff5f8a8dd43f2c119d8.jpg

 

All in all, a really enjoyable day, I hadn't done the rally thing before, but it definitely adds some excitement to the drive, having to follow the directions and keeping ahead of your rivals.

IMG-20230729-WA0002.thumb.jpg.578203b070173f57fb51f21d138da63c.jpg

IMG_20230729_123112_950.thumb.jpg.1cecd6ff5cf34d07801d490a2d6112d7.jpg

The craic was good, we got a mug each for our efforts, and everyone there was an actual car person, perfect.  Would do again, 11/10.

 

In other news, my RX8 is not home... the starter motor did not come in on time, I am assured it will ready on Monday.  Good job I had an actual rally car to play with today!

Cheers all.

 

 

 

 

Link to comment
Share on other sites

Rx8 back, and wow, starting is improved!  The new motor (I think they're all the new-style faster rpm jobs now), really gives the engine a rude awakening.

Hot and cold starts take the same time too, so I'm properly chuffed.

Got Davanti tyres on the rear (mechanic recommended), a size up from standard.  Can't feel any difference, but they do look better on the wheels, will go for the same at the front when needed I think. 

£550 credits of the realm were required in exchange for both jobs, which seems reasonable enough.  Adding that to the cost of the car, and the new cat, gives a total of £1300.  Not the cheapest I've ever had, but it is very nice.

Next job will be tidying up and painting the rest of the bodywork blebs, and then just enjoy for what's left of the no-salt season.

IMG-20230731-WA0001.thumb.jpg.1296d825d3942784f1c1dc70858ad39a.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...