Jump to content

Andy's awful autos: PLAS!


Andyrew

Recommended Posts

17 hours ago, SiC said:

I'm currently thinking Quickjacks now. Made by Bendpak - once of the largest lift companies out in the states. 

While it doesn't go as high, it goes far enough that I won't have a huge amount of spare room above in my garage anyway. They're also way lighter and smaller so easier to pack out the way when not in use.

Cheaper, but not far off the scissor lifts.

If youve got the height go mid rise lift if the price is similar. 

With the car up in the air tinkering is much more pleasant, no being on your knees or on the floor is the best part. 

Link to comment
Share on other sites

  • 2 weeks later...
  • 5 weeks later...

Its not mine! 

Okay so i know everyone loves a rough car getting (maybe) some love so lets get some pics up. 

Hows about a 1998 mx5 1.8i. 60k old lady owner whos given up driving and its had the cat stolen while parked up. A mint car sourced from a specialist years ago. Then parked by touch! 

20220814_105933.thumb.jpg.9d260f2a2e64628f2b1568fd8e9659b8.jpg

 

Link to comment
Share on other sites

  • Andyrew changed the title to Andy's awful autos: minger mazda

Exhaust removed.  Given the cosmetic challenges of the car and the fate undecided by the owner. Ive opted to do the most cost effective repair. I just replaced the cat section and will fully weld the exhaust system making it one whole peice by removing the rear ballsed and leaking rear flange.  The OG mazda box is a bit scabby but even that will outlast a shit aftermarket one.

Aftermath of cat theft

20220816_113033.thumb.jpg.bf1088af27d833eaf9bd36a790ed59cc.jpg

 

Rear section looking a bit unhealthy

20220816_113025.thumb.jpg.656c10a2f9ef65639e00c8ffb0ed648c.jpg

rear flange. Sheared stud was like that when i  got here. Flange has all but dissolved.

20220816_113029.thumb.jpg.2424dbe38805fffb8e7e849fd46f77a8.jpg

 

 

 

Link to comment
Share on other sites

Up we go!

20220825_200355.thumb.jpg.8ebd174e30aefb11e344a67e1a76c018.jpg

The allegro then.  Its blue. Very very blue.  When the car was delivered the clutch bite point was all over the show im told.  Talbot and chris tried to bleed any air out and after this the pedal failed to return. A good start it wasnt, and from then on the loves been a bit low for this blue turd. Clutch master solution worked (more on this later) 

With the heatwave i just left the car parked over at my parents place as i knew the care had a duff rad so really didnt want to use it. 

Ive booked it a place at redbourne classic car show as a mojo boost target to get some jobs done.

Some basic faults appart from the overall cosmetic issues with the car then. 

Bad points.

Wheel bearing loose and knocking its arse off. Gear shift as loose as a cock in a sock. Leaking radiator and awful brakes. Rather large oil leak/s. The most Concerning is oil from an area of the sump that has chemical meatal smeared onto it. Broken engine mount. 

Good points?  It runs okay. Nips along just fine. Its solid where it matters Suspension mounts etc etc. 

 

 

 

 

Link to comment
Share on other sites

The n.s wheel had loads of play in it. I could physically clonk the bearing play. 

Id ordered 4 new wheel bearings for all round at work, fronts about 8 quid each and a tenner at the rears as the rears sound a little grumbly. On some paperwork that came with the car wheel bearings were mentioned so i expected to find some new bearings when things came appart. 

There was also play in the trunions/kingpins/swivels/whatevertheyarecalled.

Hub off

20220827_221357.thumb.jpg.00875a40097b7cecd6ad48f03e87dd64.jpg

Wheel bearing inner race popped out revealed 3 homemade shims. I assume to lower the preload on the new bearing. The bearing looked nice and new so i decided to just re assemble without the shims. 

20220827_221430.thumb.jpg.18df2e69a75d04371655f97698699b45.jpg

Everything back together. Swivels Cleaned out and packed with fresh grease the last remaining shim removed to tighten things up a smidge tho they are fairly worn. I Need to pick up a grease gun later in the week and fill them up in situ. 

Pulling the caliper dust boot revealed some sorry looking pistons. With no new pistons to hand a smooth back and grease is all i can do for now and keep an eye on them.

20220829_160957.thumb.jpg.5d9445db9b4b15dfb0afc238180cf4cc.jpg

Back together and i forgot to take a photo so have a bad behind the wheel shot!

So did the play disappear? Not really its about 70% better. May just nip the crown nut a smidge but id like to check the play when the bearings warmed up after a run and see how it feels. 

20220829_183006.thumb.jpg.de5eea31358f1c40a74aa331ffc42e55.jpg

20220829_183021.thumb.jpg.b4249f15260aca4bcb433cc109cbcae9.jpg

While underneath i found a massive amount of play in the steering rack. It feels like a support bush worn out inside so maybe i can repair it. Thats another days problem for now tho.

 

Link to comment
Share on other sites

2 minutes ago, Andyrew said:

While underneath i found a massive amount of play in the steering rack. It feels like a support bush worn out inside so maybe i can repair it. Thats another days problem for now tho.

It will definitely be the bush as you suggest; standard on every Allegro which hasn't already had it replaced!  The club have stocks of bronze bushes to replace the original.

Link to comment
Share on other sites

I mentioned earlier that the clutch master was on its last legs and my first encounter its was dead.  With nothing off the shelf availible and not wanting to shell out 260 odd for a NOS  one on ebay.  This left me hunting for another option.  Someone like past parts where i believe mr @Angrydicky works could probably fixed it but im a low budget kind of guy. Disco 1s have a similar looking master but a larger internal bore and they are very very cheap to buy, I handily had a dead discovery with a new ish master , So i pinched it and the associated pipework, chopped the pipe and pinched the union from the aggys original and questionably re flared the end of the steel pipe as a prototype. Maybe i will re do it one day in fresh copper (probably not) bolts perfectly in the original holes too.

20220829_191324.thumb.jpg.c05aa2fce0641e5e2e3b5c393a9c0ee6.jpg

Seems to work just fine. 

 

Link to comment
Share on other sites

  • Andyrew changed the title to Andy's awful autos: Blue Belgium Beauty
12 hours ago, BeEP said:

It will definitely be the bush as you suggest; standard on every Allegro which hasn't already had it replaced!  The club have stocks of bronze bushes to replace the original.

Thats good to know.  The racks soaked in oil (just like everything else on the underside) so its probably in need of a freshen up. 

 

Link to comment
Share on other sites

The little engine mount that couldnt

Along with the busted gear mount, 5he ns engine mount had completely failed and dropped down from the bond of the rubber failing.  The NS mount was another not availible jobby, well There was one but it was mighty expensive ( theres now a cheaper on on there around £40 mark) but id seen a OS mount for an auto at a cheaper price. It looked similar, handily @Six-cylinder still had the VP 1500s old engine and that had a mount attached.  Its the same looking rubber part and plate its just bolted to its mount rather than bonded.  So the plan was to drill some holes and fit an auto one in its place. 3 out of 4 bolts snapped so that became another issue.  A whip to the local agri shop and some bolts and square nuts were purchased.

You can see below where the failed mount had been resting an inch or so lower

20220831_193311.thumb.jpg.0eec23838c9d2f73ada0d9f4ed406e02.jpg

Auto mount unbolted from its home. 

20220831_195309.thumb.jpg.d64055325e8da47a743e63dd7f1324e8.jpg

New bolts

20220831_200824.thumb.jpg.39022fae7c79c631f977f10d3d84f303.jpg

Shite ground off and some additonal holes added. 

20220831_200821.thumb.jpg.1baabe09ca908d449170b9df8f471636.jpg

Square nuts tacked in place and some rattle can matt black and that was it foe the evening.

20220831_204644.thumb.jpg.1c96c0fdd9a561cc9898538e3451de31.jpg

 

 

 

 

 

 

Link to comment
Share on other sites

  • 4 weeks later...

Screenshot_20220924-074918.jpg.aba9560d3bf263deedbd922210ed0133.jpg

Once again, ive purchased a sorry sight. 

£325 of  brokenish fiat with (at the time ) one day of MOT that was heading for the frag pile.  With the scrappy my way offering £330 and @NorfolkNWeigh able to deliver said vehicle to my workshop i felt there was zero risk, even if the thing was a complete shed. 

Whats wrong with it then?

127k

Dented door

No handbrake at all

Very grubby inside and the silly light blue, easily stained interior making things look worse. 

Some very very dead front shocks, 

Blowing exhaust with rattle.

Some geometry issues upfront 

20220915_200030.thumb.jpg.12e37ae38debaa51730f023ecaa85b3d.jpg

20220918_122848.thumb.jpg.04e9939ce61542da06b8fb4aaa5140f2.jpg

20220919_154130.thumb.jpg.d3eab29f0a6b3d5b12b7bf1fa9574537.jpg

 

Plans?

Deep Clean it 

Fix it with the the minimalist of cost. Id guess its worth maybe 500 quid on a very good day so the buget is very tight, 

Cost 325

MOT 40 

so the budget is £135 which doesnt go far! 

20220919_153951.thumb.jpg.55d9f2543d606f91797c0b283d1bb69e.jpg

 

 

 

Link to comment
Share on other sites

  • Andyrew changed the title to Andy's awful autos: SAVE THE PANDAS? Also Any doncaster based shiters?

The handbrake did zilch and the pedal felt a little low. 

Mr weigh mentioned a very expensive repair bill that got the handbrake working for about 2 weeks or so last MOT.  So i hoped for a mistake and simple fix. 

Boots off

20220919_122353.thumb.jpg.f1b19477ca39472fa202b20569503503.jpg

Wheels and drums off revealed new ish discs and pads up front and new shoes at the rear. 

However.

Nearside wheel hub. The self adjuster had fallen down and was rubbing on the rear flange.  Theres ya problem! 

20220919_121529.thumb.jpg.6c5af48585b99275cb702ba456a51a30.jpg

The offside adjust has bits lost from it so it wont self adjust. A lip on the outter of the drum means the shoes were set wrong so they could get the drums back on. both adjusters have been cleaned up and manually adjusted the lips removed from the drums aswell so we now have a lovely handbrake and good pedal feel. 

Link to comment
Share on other sites

34 minutes ago, Andyrew said:

The handbrake did zilch and the pedal felt a little low. 

Mr weigh mentioned a very expensive repair bill that got the handbrake working for about 2 weeks or so last MOT.  So i hoped for a mistake and simple fix. 

Boots off

20220919_122353.thumb.jpg.f1b19477ca39472fa202b20569503503.jpg

Wheels and drums off revealed new ish discs and pads up front and new shoes at the rear. 

However.

Nearside wheel hub. The self adjuster had fallen down and was rubbing on the rear flange.  Theres ya problem! 

20220919_121529.thumb.jpg.6c5af48585b99275cb702ba456a51a30.jpg

The offside adjust has bits lost from it so it wont self adjust. A lip on the outter of the drum means the shoes were set wrong so they could get the drums back on. both adjusters have been cleaned up and manually adjusted the lips removed from the drums aswell so we now have a lovely handbrake and good pedal feel. 

Would of thought this should be worth way more than £500 when you've finished with it based on the current market

Link to comment
Share on other sites

6 hours ago, beko1987 said:

Yey the vax worked! How did you find it? Did it leak much? 

I found another 2 packs of bags for it too if you wanted them? Can tuck them in the barn at the FoD for you when next there

Its great!

Once i got used to it i think its a very useful bit of kit.  I changed the o rings on the connectors, which cured those leaks. Theres still a drip on the socket at the front but its only minor. 

 

 

Link to comment
Share on other sites

Angle of the dangle. 

The N.s mirror was tacked in place with 4 blobs of RTV silicone. The casing wasnt busted so it hadnt taken a wallop. Maybe just broken inside. Lets sort that out. 

20220923_200452.thumb.jpg.bf8ae29d450837458956ab747afa8f0d.jpg

First thing was the little toggles holder had unclipped itself. Probably from trying to be adjusted, this clipped back in. The mirror is a very low end pattern part so the overall quality is shite and very creaky. 

20220923_200459.thumb.jpg.fb5ad06d36e8b5d10ecea4a39ec9f1f3.jpg

Carefully uncliping the glass revealed the centre hub. The  3 adjustment cables push through from the back and the little nipple on the end clips comes though a larger hole and moves inwards to clip in place so all three keep tension one each other.  The black one had ripped through as the plastic had failed. 

I wrapped a small cable tie around the metal cable and wedged it down into the void. The now ment the metal cable stuck up too far out of the hole.  Using a 'jet' lighter (that id actually found under the carpet in the 107) i heated the nipple untill it was cherry red then pushed it down into the cable tie, melting it and essentially glueing the little cable in place. 

20220923_202534.thumb.jpg.e2fe69ee326f11797fc3c341ca16754d.jpg

A bit of grease around the swivel mech of the mirror. Cleaned off the old silicone and wacked it back on the car.  The mirror glass quality is laughable.

20220924_192657.thumb.jpg.95a069fe86dd8c7ba43662e32ced11ed.jpg

 

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...