Jump to content

Triumph Toledo collection troubles - urgent advice needed!


petermcpete

Recommended Posts

There's a good chance someone will have one in stock if you are in a reasonable sized town, as said if there isn't massive damage to the outer race just fit the new inner with plenty of grease.

I always use a pair of pliers end on when tightening the nut on taper rollers, otherwise it's easy to get them waaaay to tight.

Good luck

Link to comment
Share on other sites

Just PM'd you my number fella - I'm in Brussels - slap bang in the middle of SPA and Brugge - so a garage with tools is available if you need it dude....... very best of luck finding the bits. If you don't - as you have a couple of days in Brugge - I could contact the Belgian Triumph lot - there's a Triumph specialist in Belgium but I think they basically order from Rimmer Bros....... 

Here's my number in case the PM doesn't reach you. - 0032 476 06 88 30

 

 

John

Link to comment
Share on other sites

Just PM'd you my number fella - I'm in Brussels - slap bang in the middle of SPA and Brugge - so a garage with tools is available if you need it dude....... very best of luck finding the bits. If you don't - as you have a couple of days in Brugge - I could contact the Belgian Triumph lot - there's a Triumph specialist in Belgium but I think they basically order from Rimmer Bros.......

Here's my number in case the PM doesn't reach you. - 0032 476 06 88 30

 

 

John

Amazing, thanks John, I may we'll take you up on that.

I managed to grab the bearings first thing this morning from a bearing wholesaler in Freiburg, have fitted them and am currently just going past Luxembourg - all good so far!

No luck with the pads unfortunately, and it looks like one of the piston calipers is a bit stuck, which makes sense as the brakes also pull slightly. I'll keep looking for them nearby.

Link to comment
Share on other sites

Wonder how an Irish registered Toledo ended up in Italy?

 

 

Hope you get the bearing situation sorted.

The previous owner bought it in the Midlands, brought it over to Ireland,then drove it down to his holiday home in Italy.He never used it but kept it in a dry cellar and it got started every time he visited.I had a good look at it 2 years ago and it is a really nice car.

When it was being driven down to Italy the car had serious engine trouble and had to be left in a garage in the South of France.He later went down to France with a Spitfire 1300 engine in a trailer and swopped it over,then carried on with the journey.

Link to comment
Share on other sites

Excellent 1970's style roadside (hotel) fixerating.

 

As chaps have said, that low brake pad will most likely be a sticking piston on that side of the calliper. Although I've had a partially collapsed rubber brake hose cause same problem.

 

Sometimes, Wd40 under the dust cover and work the piston in and out can help. If I recall, the calliper dust seals are a bit fiddly on the old Lucas girdling calipers. They have simple circular clip that can be a bit of a fiddle to relocate. As a roadside get you out of trouble, you could drop the dust cover off and use some sand paper to clean any crud off the end of the piston before you give it the wd40 treatment. Obs the new dust and shit will get in and you may have to go down on it again during the journey, but it is about getting home innit.

 

As for you low brake pad, swop it for the one of the other three with the most meat on it

Link to comment
Share on other sites

Are you nearly here yet?

In Bruges!

 

post-20481-0-81448700-1537005147_thumb.jpg

 

The bearings are holding up great, no heat whatsoever from them. The one pad on that side is now really ropey though, nothing left on it. Ferry back to England is tomorrow morning though, just going to nurse it back as I don't have the parts to fix it here.

Will update when back!

Link to comment
Share on other sites

Well, we made it back to the Midlands, 1700 miles in 8 days going through 12 countries (Italy, Vatican City, San Marino, Switzerland, Liechenstein, Austria, Germany, France, Luxembourg, Belgium, Holland & England) with many issues along the way sorted out (with help from here much appreciated!). 

 

post-20481-0-13586900-1537128732_thumb.jpg

 

post-20481-0-25371600-1537129951_thumb.jpg

 

I'll do a proper write up soon, when recovered!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...