Jump to content
PhilA

1951 Pontiac Chieftain - Putty

Recommended Posts

Just read this from the start..

Congrats on a fantastic car

you must have Balls like King Kong to tackle that Gearbox.....

and re-wiring too....Jeez no wonder the UK is fucked, we exported all our talent!!!

 

Hope you get that straight 8 'woofling' away nicely again

Share this post


Link to post
Share on other sites

Little bit of basic maintenance today. Pumped the tires up because at 12-14psi the steering was heavy and it was difficult to push around. 

 

Jacked the front up and had Glamorous Assistant grudgingly push on the brakes. Both exert enough force to prevent me turning the wheel so it's either one half of the cylinder is stuck or it's all out of adjustment (or both).

Masks coming in Tuesday because asbestos. Love the way the manual states to sand and grind the friction material...

Phil

Share this post


Link to post
Share on other sites

I think also I'm down to fighting air leaks and funky mixture because I dialed the slow running jets out (far more than suggested by the manual), which according to the book will take the car under light throttle up to about 20MPH.

At idle now it lopes and is far too rich, under light throttle it runs a lot more smoothly so the mixture is getting all jacked up. Opening the throttle results in a steady, positive acceleration so the main jets are functioning. I think the carb could probably do with a decent clean anyway- admittedly I have done nothing to it since it sat up last year and was stored dry. The manifold is sealing better but I'm sure it's not perfect- one runner drawing in air will affect 2 cylinders (or more, depending on how bad the leak) so that's the most likely culprit. New gaskets should see that better (proper thick, squishy ones) and perhaps the carb taken to bits and thoroughly cleaned out.

 

--Phil

Share this post


Link to post
Share on other sites

20191110_062911.thumb.jpg.03c145f0eb2ee98ce2a23b9683b19a86.jpg

Nice day yesterday so I started cleaning the car up a little more.

20191109_114530.thumb.jpg.cae9cf08eeefc07683da893bd4d360de.jpg

I decided to polish the roof. It came up well but by the time I got that far the sun was getting too hot so called an end until later.

20191109_165030.thumb.jpg.11b1c0ca4db4870057e627c567a67165.jpg

Didn't get any further with the roof but did clean up the chrome on the back of the car. It responds well.

I need a machine polisher.

 

Phil

Share this post


Link to post
Share on other sites
29 minutes ago, PhilA said:

I need a machine polisher.

 

Phil

You really do.  Can't believe it took me so long to get around to getting mine.

https://www.toolstation.com/draper-1200w-180mm-sander-polisher/p80541

Took me about an hour to do on the Lada what would have been about 1/2 a day by hand.

Share this post


Link to post
Share on other sites

20191116_160643.thumb.jpg.731ac96dfc331107a18b3567323fd338.jpg

On the car the redone light does look better. I need some more lacquer to do the other side.

 

20191116_163304.thumb.jpg.92b91599f5160316918fa59d6f085bc9.jpg

Refitted the radiator barf tube after giving it a clean. Need to flux and solder that in place.

 

Strobe light shows cylinder 8 and 1 firing at the same time. Cap is certainly bad then.

 

Phil

Share this post


Link to post
Share on other sites

20191121_204219.thumb.jpg.f15b3335f65ffda6cfe28be8f46df9a7.jpg

Scrubbing brush and gasoline. Need to pull the drum and hub off (all comes off as one) to check the brakes, so wanted it to be clean so as not to get crap in the bearings.

 

20191121_210438.thumb.jpg.02e364d89a4282c115f80d1586c122ea.jpg

Since when, in the history of never, has anybody just scrubbed at drum brakes and they've come up clean?

 

I must have bought a magical brush or something. The mind boggles.

 

Phil

Share this post


Link to post
Share on other sites
On 11/13/2019 at 11:32 PM, PhilA said:

20191113_165258.thumb.jpg.b93a94e6296d6a951986e66bb49168a8.jpg

Tried to cheer up one of the tail light lenses.

 

Not great but a bit better than it was.

 

Phil

I prefer the one on the right. Is that wrong. ?

Share this post


Link to post
Share on other sites
2 hours ago, paulplom said:

Those shoes look very thin.

They do. I need to check see how much there is left on them. I don't think there's a huge amount from the factory though.

 

Phil

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By SiC
      Decided now is definitely the time I need to scratch this itch. I don't suppose anyone has one going or thinking of going at the moment?
      Really need to sell the Laguna before I pull the trigger but if someone is getting rid for a decent price...
    • By davidfowler2000
      Edit: This is longer than initially anticipated.
      As some will have noticed, Mr cms206 of this parish reckons the death knell for the SVM is close with his recent purchase of a Saab. Going with the fact I still have a 100% Volvo fleet, as does Mr rml2345 of this parish I would personally say it's just diversification. Especially considering the amount of non Volvos cms206 has had these days.
      This aforementioned diversification continues a pace. Although the paperwork still needs to be done, I have some non Volvo incoming.

      Background:
      My aunt got the above pictured 205 back in about 2002 and ran it for about 3 years. By her accounts she put it in the lockup, got a Nissan Almera for whatever reason and basically put the 205 in to the long term deal with pile. It was initially SORN on the blue log book. Back when there was a theft of blue V5s at Swansea and everyone in the country got sent one of the new red ones, one never arrived for the 205 and after that it was properly forgetten about. Well she did. I've been keeping it in my mind every day since then. During a discussion over my birthday dinner a few weeks ago, she mentioned that she was going to pay the gardener she gets in to trim the trees to break in to the lockup because the padlock had rusted solid and she was desperate to use the space in the lockup. I said I'd do it free if I could assess the car. If it was completely fucked, it would have to get dragged out and put on a truck to go to the scrap heap. If I could get it moving, I would make it a project.
      Next day - 18th January:


      Time to break open the padlock then. Big screwdriver through the hasp and burst it within 3 seconds. Now to have a look at the car. It's dirty, 3 tyres are flat, one of them creased and the 4th is still at about 10psi. After FIFTEEN YEARS! A gentle rock confirms suspicions that all the wheels are locked so time to get all the wheels off and set about the brakes with a big swing press.
      The back wheels moved eventually. Judicious use the big hammer, two wheel bolts reinserted and a breaker bar as a lever got the back wheels turning. While the wheels were off I thought I'd see if they held air.
        
      All 4 tyres held 35psi. None of them appear to be cracked and the rubber is still "soft" to the scrape of a finger nail. Lack of sunlight attacking them I suppose but it'll get 4 new ones if it becomes roadworthy.
      After doing the back wheels, the front wheels quickly proved they could be a major problem. I took the calipers, pads and discs completely off the car and even with 2 wheel studs inserted and using the 3/4 drive breaker bar with an extra foot of length over the 1/2 bar, neither wheel / shaft would turn. So either the bearings had seized, the CV joints in the driveshafts had seized or something very sinister was happening inside the gearbox. By this time it was getting dark and cold so time to put it all away for another day.
      Another day - 24th January:
      Various discussions were had on the Scotoshite WhatsApp chat and the end result being Mr 320Touring of this parish agreed to come round for a shufty. He was wanting to check up on another car in a lockup only a mile or so away so it was a no brainer.
      As before, front wheels off, bar on the wheel bolts... nothing. What to do next? We need to use the car's own power to try to free off whatever is seized on the front wheels but the car is nose in to the lockup so we can't get jump leads to it. We need to drag it out but we don't have a tow rope however we manage to find what appears to be a self tightening dog collar / leash in the car and decide to cue MAXIMUM SKETCHINESS!!!

      A gentle tug from the ML of doom proved the NSF wheel is tight but not seized however the OSF is not moving. Fuck it... drag it while pushing from the front. If we need to shove it back in there's an old tyre in a pile of rubbish waiting to get uplifted by the council that can act as a cushion and the ML will do the job no bother. We also took the front brake discs off to minimise any drag from those.

      We decided to drag it out just enough to get my jump leads on to the battery. We had already taken the battery out to try it on the leads outside the car. Surprise surprise* it was so dead it had gone open circuit so there was absolutely no magic pixies flowing in to it. Luckily I had an old battery from the 740 that was the same size so that was obtained, inserted and then put to work. Time to leave it to charge for a wee bit.

      Now that we've got some electricity going from the ML in to the 205 it's time to see what will happen. Thanks to Mr Touring for providing the videos...
       
       
       
       
      At one point we were vexed by the daft French screw on battery terminals
      We were getting a bit desperate by this point. We used quite a lot of "easy start" and the amount of electricity was causing problems.
      We took a break at this point for 10 mins or so. Mainly to make sure we didn't get too frustrated but also to make sure the maximum possible amount of electricity was in the actual battery so that the leads were just there as a boost. This was clearly a good idea...
      Learning from all the antics of the last 15 mins or so we left it for another 5 mins. Using a clamp meter we let it get to the point that almost no electricity was flowing in the leads and therefore an almost complete charge and spraying the "easy start" ahead of time, results were finally had...
      YAY! MUCH ELATION! Oh and that old diesel stinks. Time to get the leads off, move the ML and let the 205 tick over for a few minutes to let the engine settle. Next we found out why the front wheels were not for turning...
      So yeah. All the CV Joints were completely solid. But anyways it was mission accomplished for the day. We got it moving and a general once over suggests that it should be easily salvageable therefore if auntie wants the space in the lockup, it's going to have to go somewhere. Time to put it back in and wrap up for the day.

      Thanks to 320 Touring in assistance. The list of work is substantial but not insurmountable. It needs - a battery, front discs, front pads, front calipers, front lower arms, front driveshafts, possibly bearings, rear drums, rear shoes, rear fitting kit, probably handbrake cables, flexi hoses all round, 4 new tyres, 3 of the 4 doors don't work properly, a water leak at the water pump but that can get done with a new cam belt, probably a thermostat, engine oil, filters all round, fresh fuel, a good clean, handbrake light, oil pressure light and a rear screenwash leak inside the tailgate.
      Oh and a sidelight bulb...

      Interim time:
      Lockup secured in Cumbernauld.
      Car transporter trailer booked for Wed 12th Feb to move it. The V70 will do the honours.
      Another bit of tinkering - 4th February
      So it has been agreed the V5 will be transferred in to my name. With an impending trailer move, I thought I'd go back and have another look at things and reassemble the front brakes. I've already installed a new battery so it can be started without the need for leads and it does so quite happily even though the fuel coming from the tank smells like paint. I drove it about in circles for 5 - 10 mins to free up the CV joints and scrape the rust off the brake discs. I also did some straight line tests pulling away in 2nd which seemed to free up the turbo actuator.
      I also found the radio code so I got that working but you'll have to take my word on it 'cos YouTube will just give me a copyright flag.
      I shall leave this one here just now. Not much will happen for a while. There will of course be the drama of the trailer move but once it's in the lockup a plan of action will need to be drawn up. A sensible first course will be, I think, to find someone who will give it a once over for MoT viability before any new parts are obtained. All the obvious stuff should be easily DIYable but I don't know what lurks underneath. Some things like the timing belt and water pump will be paid for but the rest will just get picked away at in due course.
      I also found some period souvenir parking tickets...

      ---ENDS---

    • By dome
      This evening I venture forth into hitherto unknown lands (Kirkintilloch) to collect my latest acquisition.

      Which, naturally, has issues.

      I have purchased my first line of defence.



      Which appears to have antigravity properties

      More will follow this evening...
    • By 95 quid Peugeot
      Right we're away, up on lift,
      Discounting painting the floor and bunging some new lights in
      1 hr in  
      Bottle of wine for closest date, of first road blast.
      Deffo a DNP


×
×
  • Create New...