Jump to content
dozeydustman

1999 Corolla E110 - Crossed wires?

Recommended Posts

Mrs Dustman has a dash cam she wants me to fit to her '99 frog face Corolla. It came with a hard wire kit as opposed to the usual fag lighter lead, so I might as well make a decent* job of it and hide the wiring completely. Trouble is I can't remember how I got the radio pod out when I fitted the DAB unit she now has. I've also got a few dash illumination bulbs to change so I might as well do it all in one hit while it's a sunny afternoon.

 

A bit of googling comes up with the US spec dash which appears to be different from the European model, or the 2002-on model. I seem to remember spudging out the dash vents to access some bolts/rivets.

 

Failing that, is there an easier place to get a switched live from (besides the radio) that doesn't involve destroying the car's interior?

Share this post


Link to post
Share on other sites

Thanks all for your recommendation. I eventually found a way of getting a switched live from the radio feed, though I suspect it's a temporary job as I had to use some fine* skills with the gas soldering iron. The piggyback fuse adaptor looks like a good idea so I may do this in the near future.

 

I've thinned out the pics I took during fitting, but someone else may find these useful, especially if hardwiring another accessory or fitting a digital radio aerial.

 

1) site camera. This one (Apeman) only came with a 3M sticky pad mount so once it's up, it's staying. I mounted it behind the rear view mirror so as not to prove a distraction while Mrs D is on the road.

 

post-24583-0-60054800-1517759764_thumb.jpg

 

2) I managed to stuff the hard wire cable up into the headlining and down the a-post trim. Cable zippers are needed to keep everything in place ideally.

 

post-24583-0-38628100-1517758466_thumb.jpg

post-24583-0-40008500-1517758499_thumb.jpg

 

3) Wouldn't even know I'd been in there......

 

post-24583-0-13272500-1517758714_thumb.jpg

 

4) Now for the vents. The little grilles just popped out, but the bezel needed spudging with a suitable* tool

 

post-24583-0-40401500-1517758784_thumb.jpg

 

5) locating the securing bolt was tricky, but using the highly scientific* method of poking around with a finger to locate and find what size it was revealed both the location and "it feels like 10mm" and was duly removed. I think there should be two of these judging by a second screw hole so when I do a better job on this I'll find a replacement.

 

post-24583-0-19132800-1517758876_thumb.jpg

 

6) Radio pod out. Bugger, the switched live (red) doesn't have a double bullet. Permanent live (yellow) does. Looking at the fuse holder inline to the kit's wiring was made of finest chinesium, and came apart quite easily. I spliced this end into the car's loom BEFORE the radio multiplug with a solder joint and a bit of heatshrink to insulate. It came with a scotchlock type joiner - no thank you.

 

post-24583-0-28560500-1517759071_thumb.jpg

post-24583-0-09197500-1517759167_thumb.jpg

post-24583-0-62178000-1517759210_thumb.jpg

 

 

7) Radio mounting frame made an ideal* earth point.

 

post-24583-0-44997700-1517759430_thumb.jpg

 

8) quick fire up of the ignition and all worked well, no smoke or blown fuses. Mrs D just needs to get her memory card now. Refitting is the reverse of removal.

 

post-24583-0-37070600-1517759816_thumb.jpg

 

 

I took the car on a short 15 minute run and no fuses blew nor smoke pouring out of the dashboard. 6ft 5 man in little Japanese car isn't particularly comfortable though. I'm happy this method worked but I wouldn't recommend splicing into the loom in a tight-ish as a permanent solution, so the piggy back connector will be ordered soon.

 

Meanwhile Mrs D was texting me and moaning the wipers bang the scuttle when in use. Small adjustment made

 

post-24583-0-39324500-1517760384_thumb.jpg

 

It's in all a sweet little car, if a little bland, and it never seems to go wrong. I did think it was pure old-man's poverty spec, but it's a run out edition before they gave them the facelift.

 

post-24583-0-13530100-1517761049_thumb.jpg

 

 

Share this post


Link to post
Share on other sites

Watching this with interest as I have a similar device to go in. Going to wait and see how the Megane does at the MOT next month before committing to hard wiring it in.

 

Ps the dash of the bug eye Corolla and the facelift are different. One of them is the same as the US versions but I cant recall which. I really like these but theyre not actually that cheap, probably because they are so good!

Share this post


Link to post
Share on other sites

Been 2 weeks since Mrs D bought some new black round things for the Corolla. With the Saab currently Failing to do anything I've been using this car as well.

 

We've had Falken Sincera SN832 tyres fitted. We chose wet grip performance over economy and noise because 1) the old tyres were shite and 2) with stepdaughter being a new driver we didn't want her sliding and skidding all over the place.

 

After 2 weeks and nearly 500 miles we're both so far impressed with the Falkens. We've not had any real wet weather to test them in, but the dry grip is significantly improved to the point there is no squeal when cornering even at low speeds, and even pushing the car hard in the twisty bits there's no drifting or back end trying to break away when lifting off the throttle. Braking distance is noticeably reduced as well.

 

Road noise is different. There's not a lot of rumble coming through from the surface, but there is a droning from the tread. Not off-putting, but there's a hint of air-raid siren to it (especially at 50mph when it hits B minor). 

 

Will report back after 2000 miles or so, or when we've had some proper wet weather.

 

Next in store for this little car is reinstate the dash panel lighting then a full service, including cam belt, ready for winter. Not done a 16 valver before. Better get my nose in the book of lies.

Share this post


Link to post
Share on other sites

A few months on and the Falkens are still proving good service after about 3000 miles, the car is quite grippy though we have a leak somewhere on the NSF wheel. It's not cracked so I'm going to get our local tyre place to seal the rim, would have done it today when I had the tracking checked and front wheels balanced - OSF one had gone 35g out of balance, so I think we lost a wheel weight. I've often found stick-on weights come off if the fitter hasn't pressed them on hard enough or cleaned the wheel sufficiently.

 

New belts are squealing again so they'll be adjusted over the weekend. Never known a car to squeal so much at startup or belts to go out of whack so quickly when new.

 

MoT is in June, and I need to find a knock from the suspension. Everything looked ok when I had a quick glance earlier, nothing too badly perished or wobbly, so that'll be a project when I get my garage in a few weeks.

Share this post


Link to post
Share on other sites

Knock from suspension appears to be o/s bottom ball joint.

 

In other news I've had the leaking rim sealed. Ideally I'm after a second set of wheels for this car for next winter, either steelies or OEM alloys, 14", so I can get the wolfraces that are original to the car refurbed.

Share this post


Link to post
Share on other sites

This little bug-eyed car is due it's MoT next Monday, so I will have some work on the car and updates to this thread at last. Need 2 split pins though for the ball joint castle nuts.

Share this post


Link to post
Share on other sites

Car is booked in for its MoT tomorrow afternoon at our friendly garage, but unfortunately I've been unable to get the ball joints off due to both illness and the castellated nuts being siezed in place. My neighbour with the angle grinder and extension lead isn't about so the garage will have to do this for me.

No split CV joints thank fuck, drop link rubbers are touch and go, and needs a brake light bulb. I can't find any other problems with the car so hopefully just a bill for fitting the supplied balljoints is all it'll need.

List of jobs I know it needs.

  1. Replace brake light bulb
  2. replace o/s/f wing
  3. regas air con & change pollen filter
  4. investigate ticking - might be the PAS pump
  5. Change water pump & flush out cooling system.
  6. thoroughly clean interior.
  7. save up for respray?

Wife & stepdaughter both love this car because it's so reliable, so I'm going to try my best to another 20 years and 180k miles of motoring out of it.

Share this post


Link to post
Share on other sites

Many kinds of Joy!

2072771912_toyotamot1.thumb.jpeg.fe391958ec189dfba9367d1ad1ee554f.jpeg

 

1606576940_toyotaMot2.thumb.jpeg.f569dccccc1168862ce37bf5ecd0a64c.jpeg

 

One advisory, and the rim has been like that for as long as I have been with Mrs D. Garage spent yesterday afternoon and half of today removing the ball joints, even grinding off the top of the castle nut & split pin hole they put up a hell of a fight. Then again I don't think I'd move easily if I'd been installed in the same place for 20 years. Emissions at idle are 0.0% CO and fast idle 0.02% so she's still running really clean. 

On 6/9/2019 at 3:53 PM, dozeydustman said:

List of jobs I know it needs.

  1. Replace brake light bulb ✔︎
  2. replace o/s/f wing
  3. regas air con & change pollen filter
  4. investigate ticking - might be the PAS pump
  5. Change water pump & flush out cooling system.
  6. thoroughly clean interior.
  7. save up for respray?
  8. Unseize track rod ends for purposes of wheel alignment and future replacement.

I can tick No 1 off for a start. 25 or so years ago when I first started reading Practical Classics, Classics Monthly and the like there was outrage with Avengers, Allegros, Mk 2 Escorts and that sort of 70's family car being restored. Maybe I should do a top notch job on this and send in my report just to upset some old giffers.

Share this post


Link to post
Share on other sites

Hmm.

Last night after coming home from my father in law's with the wife and stepdaughter, this little car has thrown up an oddity.

With the sidelights on, all the brake lights come on. Pressing the brake pedal makes the brake lights come on and the front sidelights, but not the rear.

Main headlamps on, pressing the brake pedal makes the rear sidelights come on.

I might have a crossed wire somewhere.

Share this post


Link to post
Share on other sites

wrong type of bulb been put back in a holder .....  ie a single filament bulb in a twin filament holder , they are not suppost to fit but ....

some one I know did this and caused a  similar   problem ...... 

Share this post


Link to post
Share on other sites

I'll give that a check later, what came out was a twin filament, and that's exactly what's gone back in. Could be I have it in the wrong way round or the holder is faulty/knackered as well. Will investigate at some point this week, the car rarely goes out in the dark any way so at the moment it's not a massive issue. Report to come at some point this week no doubt.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By 1970mgb
      So, someone posted on another thread a link to an Ebay listing for an LHD '74 Marina listed on Ebay.
      I called a little while ago and talked to the seller, and the story is that it was a good running and driving car 10 years ago, but has been neglected and won't run. I'm debating with myself about whether or not I want to take it on as a project.
      I know these had a terrible reputation when new, but at the same time they're actually legitimately rare in the US. I have seen one in person, and most of the estimates I've seen put the number of survivors at 10-20(although I don't know how much we can trust that).
      There's some definite appeal in the engine familiarity for me with the MGB. I MIGHT have to convert it to a manual though. In addition, there's the issue of having it shipped a couple hundred miles to me. It's listed now for $700...if I could do $500 it might be a make or break for me.
      Any thoughts here on it?
       
      EDIT: The car as it sits now is an automatic. If I swapped the transmission, it would be to a manual. Sorry for any confusion from my incorrect statement!
    • By blackboilersuit
      After many a long year of occasional contribution on here I've probably got enough old shite on fleet now to do something I should have done yonks ago and start a project thread.
      The story so far.........
      I had an 02 CRV for 6 years and it performed faultlessly as an car taking everything in it's stride. The only issue with it was the 25mpg it returned but as I worked close to home that wasn't an issue. Cue December last year and a new job saw my commute go up from 4 miles a day to 32 miles a day.

      By March I was drowning in green shield stamps so  bought the mighty diesel disAstra from Davehedgehog of this here parish. Shown here on the only off-road parking and only second car parking space I have. The garage contains a few motorbikes so I've always stubbornly stuck to a single car rule so I don't have to move motors to get bikes in and out. More on this detail in a bit.....

      A combination of broken motorcycles needing worked on, a bike trip around the Baltic and work meant that I soon realised that I had no time to prep the disAstra for its MOT  at the start of this month. It wasn't worth enough to pay to have the work done so I decided that the poor old thing would be scrapped in favour of a replacement motor.........
      The mighty Volvo (V70 D5) was purchased from Ma & Pa forddeliveryboy of this parish and migrated north of the border back to it's natural home.

      Three days after being pressed into commuting service the mighty volvo suffered a (badly) sticking caliper and much burning brake smells that had to be stripped and rebuilt before work the next day. Sticking piston at that so the whole thing was off and the brakes had to be bled afterwards. Two and a half hours in the pissing rain was a bit character building especially as the still MOT'd (by 3 days) and taxed (but not insured) astra was sitting on the drive. Decision made, insurance checked and a soon to be taken out Admiral multi-car policy will see me with two cars on the fleet again. I could have used one of the bikes but motorway commuting in the pissing rain on two wheels is no fun. The volvo needs an MOT in december so having the astra back on the road will take the pressure off getting that done if it needs work and the weather is bad.
      And so as the volvo continues to provide daily service, project astra revival starts. Known MOT work needed is frilly arches,  broken number plate and front discs and pads so nothing major. Thus far the arches have been sorted without resort to duct tape.
      After a bit of prodding.......

      And after the angle grinder was let loose surprisingly it was only the return lip that was rotten so the welder was broken out to lash on some roughly cut fresh metal.

      Linished off filled, sanded and primed. Note the use of a farmfoods brochure pulled out the bin being used as masking paper for extra shite points.

      Followed by a near perfect colour matched (*) top coat....

      Well I had black on the shelf and it's good enough to stop the primer soaking up the water so that'll do for now.
      Hoping to get brakes and MOT sorted in the coming week so more to follow soon (hopefully).
    • By Fumbler
      To mark the genesis of my fleet project thread I here present my new car: a 1997 Nissan Micra Shape-


      It really looks that good. There is a reason for this: its previous owner was an old lady who loved the thing so much so she made every effort to keep it in good shape. It originally came from Fleet in the GU postcode which suggests to me it was bought by the present dealer at auction, hence arriving down here in Kent. Before seeing the car I checked its MOT history and its only fails were thanks to broken stoplights, which shows me that it was very well cared for. I suppose an example of this was that on the last MOT, an advisory was a corroded rear silencer. The silencer on the car when I saw it was new. Methinks the lady wanted to keep it as good as possible. It was kept in a garage and so all the bumpers and black trim are very black and the tyres are in very good condition. Spare never used! Also included a free Dettol first aid kit from 1997.
      This car has 15000 genuine miles on the clock. We clocked over 15000 during the test drive! The lady owner really only trundled around her village in it and the MOT shows that it only did some meagre miles between tests. This, of course, came at a price. We saw a cherry red Micra from 2002 at the same dealer. Paint was shoddy and when they washed it the boot had massive sections of bare metal and it wasn't very happy. This car, however, is in fabulous condition and there was no contest between the two cars- it really is that good, inside and out. Immaculate interior, driver's airbag, cassette player... all there and all functioning (apart from cassette thanks to new battery and failed display). This meant that I bought it for £1600, £100 over what was my uppermost limit, but I knew I wouldn't see another like this that was in as good shape for a fair while. It was priced very ambitiously, at £1990, so I'm content in the fact I managed to slash a few hundred off the price. There wasn't that much paperwork though. All the dealership received was the logbook with 3 service stamps from 1998, 1999 and 2000, the radio key pass, a National Trust sticker, and the original paperwork holder. I suspect the old lady died and had her car auctioned, and the massive file of paperwork is now someone's egg carton, along will everything else she owned.

      As always, this car isn't exactly in showroom condition. While the inside is great and the floor is solid, and the underseal is in great shape, the not undersealed parts need a small looking at. Mainly the rear of the driver's side sill. It's really the only bubbling on the car. I suspect a well aimed stonechip managed to fester over the wintery salted roads, making it rust even more. It's around the size of a 5p piece, and will give me the opportunity to spray the insides of the sill with some chain oil to prevent any further corrosion. Behind the fuel tank there are a few rusty joints- places where the spraygun cannot get paint onto- which some Vactan and Dynax should put to rights. Alternator belt looks original because of the cracking and Nissan badges and will need doing soon as well as the front plate. As much as I like the 90's font and original dealer surround, the dishevelled R and general water ingress is a persistant MOT advisory. It could be the MOT station being strict (and most likely is considering there's a Saxo down the road with far worse blackening), however for the sake of peace of mind and all that, I'll get a new one made. The rear has already been replaced indicating this has happened before.
      All in all, I think this is a nice plucky motor. I'll have it by the end of the week; just got to sort out tax, insurance, and it's going to have an MOT. As part of the deal it's getting the MOT and an oil and filter change which will be something ticked off the list. It has some love scratches and chips here and there, but it drives well, is stiff and controllable, and should make out to be a nice summer project!
    • By Zelandeth
      Well I've been meaning to sign up here in forever, but kept forgetting. Thanks to someone over on another forum I frequent poking me about it recently the subject was forced back into my very brief attention span for long enough to get me to act on the instruction.

      I figure that my little varied fleet might bring you lot some amusement...

      So...we've got:

      1993 Lada Riva 1.5E Estate (now fuel injected, as I reckon the later cars should have been from the factory...).
      1989 Saab 900i Automatic.
      1987 Skoda 120LX 21st Anniversary Special Edition.
      1985 Sinclair C5.
      2009 Peugeot 107 Verve.

      Now getting the photos together has taken me far longer than I'd expected...so you're gonna get a couple of photos of each car for now, and I'll come back with some more information tomorrow when I've got a bit more time...

      Firstly...The Lada. Before anyone asks - in response to the single question I get asked about this car: No, it is not for sale. Took me 13 years and my father's inheritance to find the thing.


      Yes, it's got the usual rusty wings...Hoping that will be resolved in the next couple of months.

       






      Next, a proper old Saab. One of the very last 8 valve cars apparently, and all the better for it. I've driven two 16v autos and they were horrible - the auto box works sooooo much better with the torque curve of the 8 valve engine. Just wish it had an overdrive for motorway cruising...









      Next up a *real* Skoda...back when they put the engine where it belongs, right out the back. In the best possible colour of course...eye-searingly bright orange.







      Seat covers have been added since that photo was taken as it suffers from the usual rotting seat cloth problem that affects virtually all Estelles.

      Then we have possibly the world's scruffiest Sinclair C5...



      Realised when looking for this that I really need to get some more photos of the thing...I use it often enough after all! We have a dog who's half husky, so this is a really good way of getting him some exercise.

      Finally - again, I really need to take more photos of - we have the little Pug 107.



      Included for the sake of variety even if it's a bit mainstream! First (and probably to be the only) new car I've bought, and has been a cracking little motor and has asked for very little in return for putting up with nearly three years of Oxford-Milton Keynes commuter traffic, before finally escaping that fate when my housemate moved to a new job. Now it doesn't do many miles and is my default car for "when I've managed to break everything else."

      I'll fill in some more details tomorrow - I warn you though that I do tend to ramble...
    • By TripleRich
      Hi all, new to the forum.  Thought you might be interested in what I've got myself into
      I'd been after my first classic car for a while.  If it's big and made in the 70s I'm interested.  Looked at few things like P6s, Zodiacs, Victors, SD1s and various other things.  Problem was I didn't want to spend a boatload of money on something that looked alright but underneath was actually a total heap.  The solution was to buy a complete heap in the first place and spend the money fixing it.
      So in January I went ahead and bought this from a colleague at work who was moving away and needed to get shot of it.

      It's a part finished restoration (I prefer not started) and it needs a whole load of help if it's going to stand any chance of using a road again.
      Pros
      It's right up my street.  Granada Coupes are quite odd and certainly stand out from the norm.
      It still has the original engine, box, interior and most trim.
      It came with loads of panels I need to repair it (mostly original Ford stock).
      It came with so many spares I could probably build a few Granadas and still have stuff left over.
      It was cheap.
      Cons
      Most of the front end has been cut off.
      Most of the body structure is quite rotten.
      It's going to take me ages.
      I work at a restoration company and my boss kindly allows me to keep the car there.  So I've got access to all the gear I need to restore it.  I've been busy on the car for a while now so will post more pics over the coming days.
      Cheers 
×
×
  • Create New...