Justwatching Posted May 13, 2022 Share Posted May 13, 2022 Took the LTD grocery shopping. It's currently my daily driver. Pretty good so far, I just minimise parking anxiety by going when it's quiet. Cord Fourteener, Dick Longbridge, danthecapriman and 7 others 10 Link to comment Share on other sites More sharing options...
OM646 Posted May 13, 2022 Share Posted May 13, 2022 W203 update #2 Radio wouldn't turn on. Turns out it shat itself, unrepairable, and I hate to pony up with 220€ for a COMAND unit from the Lithuanian folks... HarmonicCheeseburger, BorniteIdentity and Cord Fourteener 3 Link to comment Share on other sites More sharing options...
Popsicle Posted May 13, 2022 Share Posted May 13, 2022 3 hours ago, cort1977 said: Carb linkage on the cortina is missing some bits but I managed to bodge it enough to get it working. A quick run up the cairn o mount showed that the exhaust is knackered, my new seal on the tailgate is only reducing the intake of fumes slightly and the engine is running a bit rich. And there's something amiss in the steering. I was grinning like the proverbial cat at the end of it. Thats a cracking road and car combo you've got there. Must be interesting with all the hills and bends to have something amiss with the steering! Its also a far more joyous photo than one I took with my van on that stretch of road last month. Dyslexic Viking, Cord Fourteener and cort1977 3 Link to comment Share on other sites More sharing options...
Zelandeth Posted May 14, 2022 Share Posted May 14, 2022 Today's thing I learned: The Caddy has an oil level monitoring system. It beeps (loudly - it scared the bejeezus out of me) at you and flashes the oil light at you if it's low. Next question is *why* is it that low? Was last checked about a week ago and was fine then...no oil stains on the drive (other than the historic ones from the Jag) and nothing on the back of the van. If it was burning that much I'd expect to see smoke. Will need to monitor it. Know I was parked the other way around on the drive when I last checked it, wondering if the slight slope makes a bigger difference to the reported level on the dipstick than I thought. Cord Fourteener 1 Link to comment Share on other sites More sharing options...
richardmorris Posted May 14, 2022 Share Posted May 14, 2022 Just back from Beaulieu autojumble. Not been for several years and it was a lot quieter with perhaps 1/3 of traders spaces empty. Not much for sale in the arena I liked either. Mason’s black silver shadow was smart though. some oddities spotted, one with hubnut @dollywobblersticker. big Saab display @Saabnuttoo. Saabnut, Cord Fourteener, Dyslexic Viking and 4 others 7 Link to comment Share on other sites More sharing options...
HMC Posted May 14, 2022 Share Posted May 14, 2022 Went to Tesco bought some juice (1.5L.) as the redneck bumper sticker states only juice should come in 1.5L 😂 Vantman, Split_Pin, LightBulbFun and 5 others 8 Link to comment Share on other sites More sharing options...
bunglebus Posted May 14, 2022 Share Posted May 14, 2022 Cheers everyone puddlethumper, richardmorris and HMC 3 Link to comment Share on other sites More sharing options...
richardmorris Posted May 14, 2022 Share Posted May 14, 2022 Cheers. bunglebus 1 Link to comment Share on other sites More sharing options...
Split_Pin Posted May 14, 2022 Share Posted May 14, 2022 What could be happening here 🤔 Jazoli 1 Link to comment Share on other sites More sharing options...
Jazoli Posted May 14, 2022 Share Posted May 14, 2022 It's a noobtune! Split_Pin 1 Link to comment Share on other sites More sharing options...
Split_Pin Posted May 14, 2022 Share Posted May 14, 2022 I sure hope so! I'm going to post it on Monday special delivery, it should be turned around and back to me by Thursday hopefully. He wants the cash in the box, he's clearly not* doing this under the radar 😂 320touring and BorniteIdentity 1 1 Link to comment Share on other sites More sharing options...
SRi05 Posted May 14, 2022 Share Posted May 14, 2022 41 minutes ago, Split_Pin said: I sure hope so! I'm going to post it on Monday special delivery, it should be turned around and back to me by Thursday hopefully. He wants the cash in the box, he's clearly not* doing this under the radar 😂 Looking forward to seeing how you get on with this on the auto 👍 Split_Pin 1 Link to comment Share on other sites More sharing options...
Jazoli Posted May 14, 2022 Share Posted May 14, 2022 49 minutes ago, Split_Pin said: I sure hope so! I'm going to post it on Monday special delivery, it should be turned around and back to me by Thursday hopefully. He wants the cash in the box, he's clearly not* doing this under the radar 😂 Yeah it's weird, cash only no PP or bank transfer, I bet its been quite lucrative over the years. Split_Pin 1 Link to comment Share on other sites More sharing options...
Saabnut Posted May 14, 2022 Share Posted May 14, 2022 1 hour ago, Jazoli said: Yeah it's weird, cash only no PP or bank transfer, I bet its been quite lucrative over the years. I know Karl well, and it is not what it seems He does declare and pay tax etc, the reason for the cash has a lot more to do with a vengeful ex than the taxman! lesapandre, nomiST and Jazoli 1 1 1 Link to comment Share on other sites More sharing options...
Ged Posted May 14, 2022 Share Posted May 14, 2022 Having fun attempting to change rear subframe bushes on my 305, was quite happy with how easy the nut came off till I realised the bolt had become one with the bushing. Also on one side the shock absorber bushing is seized to the trailing arm. Will probably have to cut the shock off and drill this bolt out on the subframe I think which is recessed for god knows what reason, could have saved 2p per car without this operation. I should have followed the Haynes manual and taken it to a Peugeot dealer although im fairly confident it would be "305 what now?" doubt Peugeot even have the part. Lacquer Peel, puddlethumper and beko1987 2 1 Link to comment Share on other sites More sharing options...
Zelandeth Posted May 14, 2022 Share Posted May 14, 2022 3 hours ago, Jazoli said: Yeah it's weird, cash only no PP or bank transfer, I bet its been quite lucrative over the years. Or he's been screwed over once too often by idiots issuing chargebacks. Link to comment Share on other sites More sharing options...
MorrisItalSLX Posted May 15, 2022 Share Posted May 15, 2022 21 hours ago, richardmorris said: Aussie Ford Falcon XG Panel Van! They’re getting rare here now, a local builder I know has one and keeps it tidy, he’s had it from nearly new. They suffer from rust, much more than an equivalent Aussie car if the time. Mainly because it’s a 1970s Ford that kept being made in the 90s with minor updates, rather than develop commercial versions of the new Falcon they opted to facelift the existing commercials and run them alongside the new body style. I checked the number plate on the dash but it’s from a Ford Ka(ck), not the Falcon. richardmorris, Dyslexic Viking and LightBulbFun 3 Link to comment Share on other sites More sharing options...
richardmorris Posted May 15, 2022 Share Posted May 15, 2022 6 hours ago, MorrisItalSLX said: Aussie Ford Falcon XG Panel Van! They’re getting rare here now, a local builder I know has one and keeps it tidy, he’s had it from nearly new. They suffer from rust, much more than an equivalent Aussie car if the time. Mainly because it’s a 1970s Ford that kept being made in the 90s with minor updates, rather than develop commercial versions of the new Falcon they opted to facelift the existing commercials and run them alongside the new body style. I checked the number plate on the dash but it’s from a Ford Ka(ck), not the Falcon. Pretty sure the Ford Falcon was an N reg. MorrisItalSLX 1 Link to comment Share on other sites More sharing options...
richardmorris Posted May 15, 2022 Share Posted May 15, 2022 wuvvum, nomiST, w00dy and 35 others 38 Link to comment Share on other sites More sharing options...
Stanky Posted May 15, 2022 Share Posted May 15, 2022 53 minutes ago, richardmorris said: Happy birthday! 135/10 for the cake richardmorris 1 Link to comment Share on other sites More sharing options...
richardmorris Posted May 15, 2022 Share Posted May 15, 2022 37 minutes ago, Stanky said: Happy birthday! 135/10 for the cake Birthday is actually in the week, but convenient today. Mum made the cake- she says she won’t take commissions but has taken lots of pics for people to make their own. And the original... Lacquer Peel, LightBulbFun, Stanky and 1 other 4 Link to comment Share on other sites More sharing options...
HMC Posted May 15, 2022 Share Posted May 15, 2022 another spot of this locally used wolseley. Really characterful. BeEP, Vantman, Fumbler and 8 others 11 Link to comment Share on other sites More sharing options...
wuvvum Posted May 15, 2022 Share Posted May 15, 2022 Had a bit of a frustrating weekend on the fettling front, in that I spent a lot of time doing work on the cars but don't seem to have actually achieved much. The first job of the weekend was to see if I could get the Rover's electric windows working properly. I'd ascertained that the switch pack in the driver's door and its multiplug were fine, so the next stop was the multiplug in the driver's door shut. The helpful chaps on the Rover 75 forum had given me details of which wires do what, so I set out full of optimism that I might finally get the problem sorted. Except that you can't actually access the multiplug because the door is in the way. I'd assumed you could get to it from inside the inner wing, but once I'd finally got the various rusty Philips screws holding the arch liner in place to come undone and pulled out the soundproofing, it became apparent that you can't access it from inside the inner wing at all. You also can't really access it from behind the dash - there's a hole that I can put half my hand through and I can touch the plug with the tips of my fingers, but there's no way I can get it unclipped even if I could see how the clips work (which I can't), and even if I did somehow manage to unclip it there's no way I'd get it back together again. The only way to get at the plug properly, as far as I can see, is to take the door off, and that ain't happening. So I still have non-working windows. I finished cleaning out the carbs off the 164, put them all back together with new diaphragms and gaskets, and this afternoon I refitted them to the car. Put everything back together, ran the jump leads across from the Mazda, turned the key and... it's still running like a bag of shit. (It wouldn't fire at all to begin with, but that was because the dipstick had spun round and was shorting out against the LT wire to the distributor.) So I think it must be ignition related - there's plenty of fuel getting through and the carbs all looked OK (they're Stromberg 175s so a fairly simple unit). Problem is I'm not very good at diagnosing ignition-related faults, and I can't afford to start playing parts darts, especially with the price of old Volvo bits. So I'm not sure where to go next. I jacked the front of the Renault 6 up and took off the driver's side front wheel to see if I could get any grease into the brake caliper sliders in an attempt to stop the brake sticking on. That turned out to be a non-starter as there was no gap anywhere to get the grease in between the moving parts. They're a very odd design of caliper - the sliders aren't the usual pins, they're a sort of rail which is sandwiched between the two halves of the caliper and the whole thing is held together with clips and split pins. Anyway, while I was in there I noticed that the pads are getting pretty low (the brake must have been sticking more than I thought as last time I checked there was loads of meat on the pads and the car hasn't done that many miles since then) so I'm going to have to change those, which is going to be fun - the HBOL says that the pins holding the caliper together need to be renewed every time it's taken apart, but I haven't found a source for new ones so they're going to end up getting reused I think. I started to take the EGR pipework off the Doblo to see if I could clean the valve out (I've been driving around with it unplugged for the last few days which has cured the stuttering but has brought the EML on) - the pipe from valve to inlet manifold came off easily enough but the Allen bolts that hold the pipe from the exhaust on to the valve assembly are a right twat to get at and I couldn't undo them with the tools I had available. So I've ordered a blanking plate off eBay and I'm just going to blank it off. Stupid bloody things anyway. I made some progress with the 107, but not as much as I'd hoped. I ran it up to my mate's yesterday evening and we got the bit of welding done that it failed on, and we also made a brake pipe up for it. I'd been hoping to get the pipe fitted today, but the bleed nipple on the rear drum sheared off so I now need to buy a new wheel cylinder before I can go any further (I could have fitted the pipe I suppose but without the ability to bleed it I ran the risk of leaving the car with no brakes). This is annoying as it'll be the first actual expenditure on the car - everything else I've done to it so far has been done with bits I already had lying around. I also discovered that the union where the original brake pipe joins to the flexi is essentially a blob of rust and has no chance of coming undone via conventional means, so I'm going to have to cut through the pipe and hammer a socket onto it, which is an added complication. The front union cracked off easily enough though, which is a relief. I've made a temporary plug for the front pipe to try and stop all the fluid draining out of the master cylinder while I piss about trying to get the rear union off - I took a spare male union and trowelled it full of JB Weld. Hopefully that'll do the trick. Anyway after the bleed nipple broke off I pretty much gave up on fixing anything else, so I cleared out the Laguna ready for its lucky* new owner to collect it next weekend. The other job that had been on the list was to do an oil change on the XF, but the filter I ordered hadn't turned up so that's going to have to wait as well. Split_Pin, BorniteIdentity and mercedade 3 Link to comment Share on other sites More sharing options...
tom13 Posted May 16, 2022 Share Posted May 16, 2022 Joined the 107 gang. Kept seeing people rave about them on here and couldn't resist the cheapness of tax insurance etc. Anything I need to look out for? First task is a wheel bearing. Had a recent clutch which I have heard is a major weak point. paulplom and loserone 2 Link to comment Share on other sites More sharing options...
Zelandeth Posted May 16, 2022 Share Posted May 16, 2022 8 minutes ago, tom13 said: Joined the 107 gang. Kept seeing people rave about them on here and couldn't resist the cheapness of tax insurance etc. Anything I need to look out for? First task is a wheel bearing. Had a recent clutch which I have heard is a major weak point. Clutches on the earlier cars were weak, a larger one was used after the first couple of years. I've seen several with the clutch cable very poorly adjusted and a stupidly high pedal. In my case this was because the dealer was adamant that it was self adjusting - it isn't! Suffice to say once the warranty was out and I started doing my own servicing I found the adjuster and suddenly had a far nicer clutch. Sadly the release bearing died about 12 months later, and I'm sure having spent nearly four years way out of adjustment contributed to that. Given I've driven several all with a really high clutch it wouldn't surprise me if that was due to duff info in the dealer service guide or similar. Had mine for 9 years, and only real things of note were the clutch as mentioned, one CV joint started to seize up, replacing the driveshaft was the easier solution there at something like £60 fitted by my local garage, a wheel bearing, radiator and AC condenser. Radiator is a bit of a bugger as you have to remove the lower cross member to get it out and the bolts are made of cheese. The exhaust was just at the point of needing done when I moved the car on. The rear hanger always rots off way before the system itself dies, but it's simple enough to fabricate a replacement. Beyond that it was just normal consumables. For 9 years and 60K miles, a good chunk of that mileage being a daily commute into Oxford I'd say it did pretty well. At this point rust is the main thing I'd be looking for. There really wasn't much by way of substantial looking rustproofing on the underside. tom13 1 Link to comment Share on other sites More sharing options...
tom13 Posted May 16, 2022 Share Posted May 16, 2022 6 minutes ago, Zelandeth said: Clutches on the earlier cars were weak, a larger one was used after the first couple of years. I've seen several with the clutch cable very poorly adjusted and a stupidly high pedal. In my case this was because the dealer was adamant that it was self adjusting - it isn't! Suffice to say once the warranty was out and I started doing my own servicing I found the adjuster and suddenly had a far nicer clutch. Sadly the release bearing died about 12 months later, and I'm sure having spent nearly four years way out of adjustment contributed to that. Given I've driven several all with a really high clutch it wouldn't surprise me if that was due to duff info in the dealer service guide or similar. Had mine for 9 years, and only real things of note were the clutch as mentioned, one CV joint started to seize up, replacing the driveshaft was the easier solution there at something like £60 fitted by my local garage, a wheel bearing, radiator and AC condenser. Radiator is a bit of a bugger as you have to remove the lower cross member to get it out and the bolts are made of cheese. The exhaust was just at the point of needing done when I moved the car on. The rear hanger always rots off way before the system itself dies, but it's simple enough to fabricate a replacement. Beyond that it was just normal consumables. For 9 years and 60K miles, a good chunk of that mileage being a daily commute into Oxford I'd say it did pretty well. At this point rust is the main thing I'd be looking for. There really wasn't much by way of substantial looking rustproofing on the underside. Cheers. Exhaust has had some alterations. Its had a new backbox and the midbox replaced with a sleeve. I need to have a look at the hanger though as something funny is going on. Did you do the wheel bearing yourself? Link to comment Share on other sites More sharing options...
Split_Pin Posted May 16, 2022 Share Posted May 16, 2022 I won't lie by saying that I'm not even slightly nervous at putting my Saab's ECU through the UK postal system . Next day Special Delivery Tracked should hopefully see it right! paulplom and AnnoyingPentium 1 1 Link to comment Share on other sites More sharing options...
wuvvum Posted May 16, 2022 Share Posted May 16, 2022 It'll be reet. I sent the Rover ECU through the post twice and it was fine. Split_Pin 1 Link to comment Share on other sites More sharing options...
HMC Posted May 16, 2022 Share Posted May 16, 2022 Just watched Used Cars (1980) To film buff it’s a bit of commentary about America itself. I tend to watch it for the car overload. It’s based around 2 competing used car lots and the more ramshackle of these is a great spotting ground for tired US tin. This time round I did a spot of a 73 coupe de ville, (make model and year as huggy) which is shot at during a pirated commercial during a presidential address Got me wondering if @danthecapriman has spotted his make model and year amongst the ranks of stuff for sale. paulplom and danthecapriman 2 Link to comment Share on other sites More sharing options...
danthecapriman Posted May 16, 2022 Share Posted May 16, 2022 7 minutes ago, HMC said: Just watched Used Cars (1980) To film buff it’s a bit of commentary about America itself. I tend to watch it for the car overload. It’s based around 2 competing uses car lots and the more ramshackle of these is a great sporting ground for tired US tin. This time round I did a spot of a 73 coupe de ville, (make model and year as huggy) which is shot at during a pirated commercial during a presidential address Got me wondering if @danthecapriman has spotted his make model and year amongst the ranks of stuff for sale. I’ve never seen that, but I often go on YouTube and just search for stuff like Los Angeles 1970’s, New York 1980’s etc and watch all the old road and street filming. Usually packed with old Detroit iron! HMC and Dyslexic Viking 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now