Jump to content
richardthestag

Range Rover resto - Project Southpaw p23

Recommended Posts

Been a busy 6 months on my old Range Rover that I own 50/50 with Fathathastag

 

Bit of background first..

 

We bought it March 2015 just as genuine early Range Rovers were starting to get noticed. Alas not early enough that we could have got it for a couple of hundred quid. 

 

The car had been owned for decades by a Land Rover enthusiast and this particular car retained a lot of features unique to pre 1973 Range Rovers. Sadly he died a few years back and the car was left outside the front of his house. 

 

I spotted it on eBay and arranged with the owners widow to view. There were no bids and my offer was good enough to take the auction off.

 

The engine had been part way through a top end strip down when work stopped, I had no idea even if the car would move. But rented a trailer and relocated it from Watford to North Devon where fathathastag has a barn suitable for storage.

 

post-3439-0-45184400-1482240805_thumb.jpg

 

post-3439-0-36750600-1482240806_thumb.jpg

 

The project is on the right, we towed it into the field and pushed it into the barn

post-3439-0-45674400-1482240807_thumb.jpg

 

In May 2015 I got to do an assessment of the car. body wise most outer panels were ok, the inner wings looked ok, it clearly needed some work but was unsure how much at this point. main objective was to see if the engine was a runner.

 

post-3439-0-68372900-1482241011_thumb.jpg

 

post-3439-0-81773200-1482241012_thumb.jpg

 

post-3439-0-24292200-1482241014_thumb.jpg

 

post-3439-0-39181700-1482241015_thumb.jpg

 

Found that the gearbox and axles were original to the car, but the engine was from an earlyish SD1

 

while the seat covers are not original some of the plastic kitkat seat coverings are underneath, the rear seat especially

 

post-3439-0-92598800-1482241116_thumb.jpg

 

post-3439-0-86338800-1482241117_thumb.jpg

 

post-3439-0-79508600-1482241118_thumb.jpg

 

post-3439-0-36132900-1482241119_thumb.jpg

 

The head has some nasty corrosion very near the fire ring seal, 

 

post-3439-0-31261600-1482241120_thumb.jpg

 

When I refitted the head one of the bolts tore the thread out. bastard but not entirely uncommon with the alloy blocked RV8

 

post-3439-0-39533800-1482241304_thumb.jpg

 

 

 

 

 

Share this post


Link to post
Share on other sites

rolling forwards to September 2015 and I got it running

 

After fixing the broken thread, and refitting the n/s head

 

post-3439-0-56979700-1482241618_thumb.jpg

 

Then removing sediment and varnish from the float chambers

 

post-3439-0-18441000-1482241615_thumb.jpg

 

giving up on finding the homemade immobiliser that stopped the retrofit fuel pump from working

 

post-3439-0-50179800-1482241616_thumb.jpg

 

Then finding that the ignition was miles out

 

post-3439-0-71723100-1482241617_thumb.jpg

 

It started and sounded real sweet

 

post-3439-0-63629400-1482241619_thumb.jpg

 

Share this post


Link to post
Share on other sites

I do like these early Range Rovers - there is one 'on the road' near my in-laws, over by Erith/Belvedere. I think it is actually in running order as it is parked on the street, it's quite tatty but it has the charm of a 'working' vehicle. Never stopped to take a closer look...

Share this post


Link to post
Share on other sites

Then I left the project for 9 months until June 2016 when I started on strip down and body refurb.

 

At this point I was planning to tickle the welder a little. omg how wrong was it.

 

Stripped the interior out, note the unmolested dash and original vinyl floor coverings

post-3439-0-24708800-1482242346_thumb.jpg

 

post-3439-0-45148700-1482242366_thumb.jpg

 

As the doors would need lots of work, I stripped them down in situe. wanted to use them as a reference point anywaypost-3439-0-30294500-1482242501_thumb.jpg

 

Alloy boot floor was already loosely fitted so removed

post-3439-0-92719200-1482242502_thumb.jpg

 

Fuel tank is homemade and very robust. I will probably stay in the car

post-3439-0-97702700-1482242503_thumb.jpg

 

Strip down is starting to make me nervous at the sheer number of patches

 

post-3439-0-94512500-1482242504_thumb.jpg

 

I then started on the front end.. Most bolts undid without drama which was nice. the rust was not quite so nice

 

post-3439-0-50154700-1482242687_thumb.jpg

 

post-3439-0-81041700-1482242713_thumb.jpg

 

I opted to remove the loom, a to protect it but also to allow me to remove the add ons and chocbloks

post-3439-0-41839800-1482242716_thumb.jpg

 

post-3439-0-99145100-1482242717_thumb.jpg

 

post-3439-0-38798100-1482242719_thumb.jpg

 

The loom for dash and front of the car is out, 

post-3439-0-45025400-1482242886_thumb.jpg

 

This left the interior stripped out. I left the screen in as a) it is already chipped B) I am collecting spares and c) there was only me on my own

 

post-3439-0-90980100-1482243043_thumb.jpg

 

post-3439-0-43707400-1482243045_thumb.jpg

 

post-3439-0-59104000-1482243046_thumb.jpg

Share this post


Link to post
Share on other sites

Weren't the really really early ones badged something else?

.

You may have seen prototypes with "VELAR" badging, it was simply to disguise the car and never intended for production.

Supposedly the name came from the description "Vee Eight LAnd Rover".

Share this post


Link to post
Share on other sites

I nervously started on the front inner wing. On these early Rangies they bolt on. This one had a very thin weld holding it to the bulkhead.

 

Alas the wing wasnt looking quite as salvageable as I first hoped :(

post-3439-0-31791000-1482243258_thumb.jpg

 

post-3439-0-81367500-1482243259_thumb.jpg

 

post-3439-0-28461300-1482243261_thumb.jpg

 

Bolts removed and thin weld cut and the inner wing is off

post-3439-0-92328800-1482243262_thumb.jpg

 

post-3439-0-25170900-1482243264_thumb.jpg

 

And it is fucked

post-3439-0-34381800-1482243460_thumb.jpg

 

Ummm

 

post-3439-0-44186000-1482243265_thumb.jpg

 

That footwell is very patched

post-3439-0-03242900-1482243459_thumb.jpg

 

 

It really didnt take much effort to just peel it away. the repairs were solid but they were welded over rust which had continued to rust. Bugger

post-3439-0-64319200-1482243461_thumb.jpg

 

post-3439-0-60891600-1482243462_thumb.jpg

 

Count the layers of patches - there should be two layers here

post-3439-0-72713000-1482243463_thumb.jpg

 

This is the footwell out. It weighed over 20kg

post-3439-0-57454600-1482243465_thumb.jpg

Share this post


Link to post
Share on other sites

Next up is to remove the cab floor and gearbox cover. Most of the fixings were roof bolts with square nuts but most of them shifted

 

post-3439-0-70316600-1482244201_thumb.jpg

 

post-3439-0-68655800-1482244202_thumb.jpg

 

Chassis has a pleasing ring to it was tapped with Land Rover special tool #1

post-3439-0-82249100-1482244203_thumb.jpg

 

I will get away with localised repairs to the gearbox cover which is nice

post-3439-0-75573000-1482244204_thumb.jpg

 

but this isnt, and yes that is bathroom silicon sealant, fecking tons of it

post-3439-0-72351400-1482244205_thumb.jpg

 

post-3439-0-84787800-1482244206_thumb.jpg

 

Drivers side sill I knew would need attention

post-3439-0-94089800-1482244207_thumb.jpg

 

The front inner wing on the drievrs side is unpleasant

post-3439-0-40509200-1482244209_thumb.jpg

 

Patches over patches. nursed from one mot to the next

post-3439-0-73913100-1482244210_thumb.jpg

 

The bulkhead side is as I expected unfortunately

post-3439-0-27154600-1482244212_thumb.jpg

 

The inner wing is worse than the drivers side

post-3439-0-67342600-1482244221_thumb.jpg

 

Oh dear

post-3439-0-17802000-1482244223_thumb.jpg

 

 

 

 

Share this post


Link to post
Share on other sites

I promised myself that at this point it had to start getting better soon! I committed to avoid any further bodgery and get the body frame back to factory spec. While Alan the previous owner was a very good welder his lack of rust proofing and copious use of bathroom silicon sealer had condemned the fate of the lower 8 inches of the body frame all around. Ouch

 

This is what remained of the bulkhead side

post-3439-0-16342200-1482245031_thumb.jpg

 

The a post had many layers of patches

post-3439-0-87773200-1482245032_thumb.jpg

 

post-3439-0-23580000-1482245034_thumb.jpg

 

post-3439-0-62420500-1482245035_thumb.jpg

 

Removed the remnants as you can now buy a complete bulkhead side repair panel

post-3439-0-11968300-1482245038_thumb.jpg

 

thats better :D

post-3439-0-51091400-1482245039_thumb.jpg

 

After removing the patches there wasnt a huge amount of a post left. again repair panels are available. Also I wasnt happy with the sill, a home made heavy duty box section. mainly because it wasnt going to fit with the other repairs. also it had been welded on wonky so it was going to get cut out

post-3439-0-29770700-1482245041_thumb.jpg

 

braced the roof between the chassis and a bross beam

post-3439-0-49113700-1482245042_thumb.jpg

 

and cut it out.

post-3439-0-92501200-1482245043_thumb.jpg

 

post-3439-0-33479800-1482245045_thumb.jpg

 

post-3439-0-84877600-1482245054_thumb.jpg

this is the remnants of the panel that sits behind the b post. again patches over patches

post-3439-0-42936500-1482245056_thumb.jpg

 

It does start to get better from here :D

Share this post


Link to post
Share on other sites

The sills come from from Froggatts Easy On panels, perfect fit

 

Inner sill bolts via mounts to the chassis

post-3439-0-41272500-1482245886_thumb.jpg

 

Outer sill goes over the top and then is checked against the gearbox cover and rear passenger floors for alignment. all the bolt holes were mm perfect.

 

post-3439-0-38998200-1482245888_thumb.jpg

 

Then pop rivet the two together and weld the bastards

post-3439-0-50794800-1482245890_thumb.jpg

 

refit and check alignment

post-3439-0-29935200-1482245892_thumb.jpg

 

post-3439-0-76328200-1482245893_thumb.jpg

 

post-3439-0-25164200-1482245895_thumb.jpg

 

Happy days I am making progress :D

 

Made the final cut on the a-post, it was nasty but the top half is very solid. repair panels are available form Froggatts again.

 

post-3439-0-63495200-1482245896_thumb.jpg

 

refitted door to check alignment

 

post-3439-0-91396600-1482245897_thumb.jpg

 

post-3439-0-16973800-1482245899_thumb.jpg

 

Refitted the remains of the bulkhead side for alignment and used a jack on the bottom hinge to get it where I wanted.

post-3439-0-73589200-1482245900_thumb.jpg

 

checking and checking again before welding

 

post-3439-0-05767900-1482246397_thumb.jpg

 

post-3439-0-80595700-1482246492_thumb.jpg

 

salvaged and welded the bonnet release catch onto the new bulkhead side panel

post-3439-0-06542600-1482246494_thumb.jpg

 

post-3439-0-29750500-1482246495_thumb.jpg

 

post-3439-0-52031400-1482246496_thumb.jpg

 

post-3439-0-73130100-1482246497_thumb.jpg

 

 

 

 

Share this post


Link to post
Share on other sites

You may have seen prototypes with "VELAR" badging, it was simply to disguise the car and never intended for production.

Supposedly the name came from the description "Vee Eight LAnd Rover".

 

Is this true? I only ask as every time I've read anything on early Rangies and the prototype 'VELAR' moniker, the response to the 'What does it mean/stand for?' has always been that it doesn't mean'/stand for anything, it was just a plausible name someone made up using the letters from LAND ROVER that sounded a bit snappy (& maybe a bit exclusive/trendy???) and didn't have any associations with LR (or BL at the time). 

I actually hope you are right and it does stand for something rather than being a bland meaningless name.

 

Always liked the original RR's ever since the dad of a friend had one when I was a nipper. Never really like the four door ones. Should have bought one some years ago when they were cheap but had no need for a: 4WD, b: V8 or c: V8 4WD! - regretting it now. Good luck with the resto.  

Share this post


Link to post
Share on other sites

Hooray for repair panels that fit! It is coming together nicely now - after a rather frightening start.

 

What an interesting thread - I do like the Range Rover. Bizarrely, when I was a child I genuinely believed NASA's Lunar Rover was made by Land Rover - and could never understand why they didn't make more of it! :shock:

Share this post


Link to post
Share on other sites

Jeez, that's kwality bodgework you're undoing there. I wish there was a law banning people from car ownership if they are caught using silicon sealant, bridgeagap, pop rivets where there's should be welds and general ruinage of vehicles. Having said that, I'd have been arrested several times during my late teens.

Is it finished yet?!

Share this post


Link to post
Share on other sites

There are lots of theories about VELAR origins. IIRC the company was registered in Croydon to further throw off then scent. The VELAR were indeed made using Alvis and Rover lettering the A was an inverted P6 V with a bar added

 

V eight LAnd Rover is one theory

Another is that VELAR is Spanish for a Veil.

 

An extraordinarily high number of the original Velars have survived and go for very strong money indeed, aim for 6 figures and you shant be disappointed.

 

LR didnt take long to get the concept right. The first two had more or less captured with profile and the 3rd prototype had a lot of the detail in lace. Alas none of these three survive

 

#1

post-3439-0-01506900-1482247988_thumb.jpg

 

#2

post-3439-0-71106700-1482248009_thumb.jpg

 

#2 and #1 together

post-3439-0-68771300-1482248022_thumb.jpg

 

#3

post-3439-0-46100300-1482248036_thumb.jpg

 

 

 

 

 

 

.

Share this post


Link to post
Share on other sites

Jeez, that's kwality bodgework you're undoing there. I wish there was a law banning people from car ownership if they are caught using silicon sealant, bridgeagap, pop rivets where there's should be welds and general ruinage of vehicles. Having said that, I'd have been arrested several times during my late teens.

Is it finished yet?!

 

nope it is a way off still, reckon it should be getting there by June 2017

Share this post


Link to post
Share on other sites

I was really struggling with shitty wire feed and over all control of my old SIP Migmate 130, get a weld going and the voltage would randomly fluctuate to the wire feed causing burn back and all sorts of other shite. I got more and more fed up with the damn thing.

 

This was strong and the hammer of doom could not flex it but it looked shit

post-3439-0-49441700-1482248524_thumb.jpg

 

So I cut it out

post-3439-0-87803300-1482248525_thumb.jpg

 

Made up a repair

post-3439-0-14958500-1482248527_thumb.jpg

 

Butt welded it in

post-3439-0-53180700-1482248528_thumb.jpg

 

Made up the leading edge

post-3439-0-02257600-1482248530_thumb.jpg

 

Welded and smoothed it in 

post-3439-0-32855600-1482248531_thumb.jpg

 

post-3439-0-84718800-1482248532_thumb.jpg

 

And am much happier, sliver of filler and it will be hidden. As a bonus the door shuts great with no shims and the gaps are even all around.

 

post-3439-0-90201700-1482248654_thumb.jpg

 

Share this post


Link to post
Share on other sites

On to the floor pan. The big problem here is with the qualitay of the pattern part. 

 

In Range Rover circles anything painted black is a pain to fit, Froggatts are going through and reproducing a lot of stuff but there is a wedge of stuff that is difficult to work with.

 

An example in case is the foorwell. the repair has the strengthening ribs which is good.

 

post-3439-0-75845800-1482250613_thumb.jpg

 

But it also includes a chunk of the bulkhead side but not in the way that it was originally manufactured. So that has to be removed.

 

Then the lip has to be folded 180degrees

 

post-3439-0-67974300-1482250615_thumb.jpg

 

Then you are pratting around with profiles. The profile against the bulkhead side is good. But the profile where it meets the trans tunnel is not. and when you get that right there is no longer the flat area to fit the bulkhead mount.

 

Arghh

 

Days of farting around with this but I can now do them in a couple of hours

 

the key was making up a wooden former for the inner section and bending it, here you can see the difference in profiles

 

post-3439-0-01231600-1482250617_thumb.jpg

 

With the profiles sorted I was able to clamp the bulkhead mount to the footwell 

post-3439-0-75352100-1482250618_thumb.jpg

 

Checking inside and out

post-3439-0-14518900-1482250620_thumb.jpg

 

post-3439-0-61819800-1482250621_thumb.jpg

 

post-3439-0-92242100-1482250622_thumb.jpg

 

Before fitting my brand new Easy on Inner wings, expensive but because you know they are correct, they can be used as a reference point

post-3439-0-48732900-1482250624_thumb.jpg

 

Then welded the body mount and tightened that to the chassis

post-3439-0-83175400-1482250625_thumb.jpg

 

post-3439-0-49689300-1482250627_thumb.jpg

 

The inner wing bolts to the bulkhead front and side and also the body mount

post-3439-0-60113400-1482250638_thumb.jpg

 

The sill is attached to the footwell using screws and spire nuts

post-3439-0-81258600-1482250639_thumb.jpg

 

post-3439-0-38925400-1482250641_thumb.jpg

 

post-3439-0-29223400-1482250643_thumb.jpg

 

Yeah one quarter solid again

post-3439-0-92026200-1482250644_thumb.jpg

 

 

 

Share this post


Link to post
Share on other sites

Hooray for repair panels that fit! It is coming together nicely now - after a rather frightening start.

 

What an interesting thread - I do like the Range Rover. Bizarrely, when I was a child I genuinely believed NASA's Lunar Rover was made by Land Rover - and could never understand why they didn't make more of it! :shock:

 

Bloody hell - so did I !!!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By BoggyMires
      Now in my mucky hands is this S Type Mondeo Lincoln. It's not like a Mondeo Lincoln  though, just uses some of the bits as it's from a time when jaguar was experiencing some 'technical' issues. 
      It has managed to hang onto the feel of a premium car but for the use of cost saving interior plastics made from the same gear that land Rover used in the discovery 2 of the same era, I know, I have one of those too! That has some BMW switches in it though.
       
      This jaag was cheap. Why did I buy it? All I wanted really was a small convertible for the summer to smoke around in, this is the polar opposite. 
      The price was good but these cars are without their expensive issues. I liked the body. It's virtually rust free, a freak of nature and it had a set of premium tyres on it which suggested it's had some money chucked at it.
       
      That's all I wanted really from it. The bolt on stuff and mechanicals are fairly easy to sort out, plus I can upgrade as I feel fit.
       
      Today I've been bonding with this machine. It's got to beat the 3 series I have as a good daily or it's out. It's going to be a tall order, the 318 is bionic!
       
      I have many miles to do in the next few months, I need a motorway cruiser auto. The odd jaunt for a few hundred miles is the 318's and my clutch legs limit!
       
      Now, this car has been owned previously by a few members on here, the work it requires is because it is a cheap car and 20 years old and has a jaguar badge on it. There are a few issues with it.
       
      As said, it has to be put into immediate service. I've owned it 2 days and it's already done over 300 miles, and will do all that again tomorrow! So let's get started!
       
      After about 100 miles yesterday, I reversed it for the first time in my ownership and when braking the noise was alarming! Had a look and the outer rear brake pad was metal on the disc. I only had another 60 miles to go!
      A phone call on the move saw a set in stock back home to be picked up. Sweet.
       
      That was yesterday, I've got a day now to change the rear pads and sort out the dropped headlamps with a couple of screws... A couple of hours it'll be Sorted... He says...
       
      WIND BACK CALIPERS! Yes, they are. My special tool? Sorry? What? No tool?
      Well, I cobbled together a bar and a pair of molies but Christ, that was messing about! I wanted to secure the caliper to the mounting to hold it still but the sliders internal thread was cross threaded on both sliders, so I had to tap them out first. It worked but not without a fight. Then my neighbour came over to have a nose at the new aquisition... Him: Morning, how you getting on"?, Me: "Shit, you haven't got a brake caliper tool have you"? Him: "Yeah, I'll go get it". 
       
      LIFESAVER!!!
       

       
      Sticky slider syndrome ^
       

       
      Fully padded up ^
       
      I took a look around under there, it's nearly all shot. Most ball joints are exposed to the elements so all need replacing but not before a decent jet wash.
       

       

       
      There's little play in the joints so all that goes on the list of parts and graft! Wheels on, I loosened and torqued all the wheel nuts around the car and done the Tyre pressures, we were running soft all round.
       
      Next was the front lights. A screw mod can be done but I took the back off the units and they were, well toast. Nothing much holding the inner lenses still at all. There was only one thing for it...
       

       
      I had readied myself for this. I got hold of a replacement lamp mounting kit with all parts made from nylon. This involved dissecting the lamp which was tough! The mounts that came out, or what was left of them were weaker than Jacobs crackers and just crumbled. To get the bumper off, the plastic under tray bolts were all seized so I had to grind them off. More knackered parts were seen. The auto box cooler has shed most of it's cooling fins, the radiator is sweating and the power steering is hemorrhaging fluid on full lock. There's also a coolant leak at the thermostat housing and there's a high pitch whine at 1000 RPM which turns out to be the alternator. More for the list.
      Still, back to the lights. I need to be able to see tonight so I took a level off the tourings lights and marked on to a wheely bin, these are pretty spot on. Then I can use the bin for the Jaags lights and I won't be far off 
       

       
      Going back together nicely it was a good time to run some tcut over the faded lenses. They need a more intense compound and a machine but will do for now.
       

       
      Looks smart yo!
       
      Then it got dark...
       

       
      I then drove 120 miles in it and drove it like it was stolen. It had it, all of it! Slight brake judder at 90 and I couldn't get the alignment done as I had no time (see above pics)
       
      So now we have to price up priorities like the knackered joints on the rear and a full service, two Goodyears and investigate the power steering leak which, I'll hazard a guess at the rack seals are fubard. 
       
      So in summary, I got a bargain barge that has it's fair share of issues, the interior quality is a bit shocking in places but when the hammer is down, none of this matters! It fits in, it can be a proper giffer cruiser with radio two on at 30mph but it'll turn into a bruiser with some oldskool hardcore at a tonne. It's come to a good home.
    • By strangeangel
      I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.
       
      So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.
       
      Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.
       
    • By snagglepuss
      Didn't bother to do a collection thread as was a 30min drive so fairly boring.
       
      Yesterday I won this
       

       
      Which is effectively going to replace the civic and the xantia.
       

       
      Picked car from a bodywork guy in foreign lands (Yorkshire).
       
      First thoughts are that I think it has been sitting for a while but started straight up. Apart from service bits and potentially a cambelt everything seems to be good with it. Comes pre dented.
       
      Current is differently abled tax so that will need to be changed.
       
      Windscreen has small crack in passenger side.
       
      Runs really cold, this is after 30 miles of motorway

       
      Mind you it honks. Properly honks. Not as much as the focus I got from Shadow but not far off.
       

       
      List of jobs
       
      Oil change
      Spark plugs
      Air filter
      Thermostat
      Rear boot struts
      Front discs and pads
      Cam belt plus bits
      Ball joints
      Drop links
      Rear anti roll bar bushes
      Stereo code
      Windscreen crack
      Swimming pool emptied from boot wheel well
      Seal rear light clusters
       
      And a big does of cleaning
×
×
  • Create New...