Jump to content

Cavalier mk2 - another blue giffermobile.


4wheeledstool

Recommended Posts

This car is certainly a bit of an oddity in that the majority of the car pox was confined to the bottom few inches of the rear half of the bodywork. Although it looked pretty bad a few months ago, I still think I've been lucky with its condition. (Not as lucky as I was with my other Cavalier!) :)

Link to comment
Share on other sites

Spoke too soon! You can just about see some blown areas of metal in the first of the two pics above  (driver's side) - today I had a good stab at it with a hammer and screwdriver. After removing some of the sound deadening material, this was the view of the driver's footwell.

IMG_20190724_134728.thumb.jpg.fc82c080489c821a1a39629c2f9bdfa8.jpg

After removing the thin metal from around the holes in the outer layer, and the surrounding area of the inner layer.

IMG_20190724_144031.thumb.jpg.05a8b3444d6fb766e518bee8510f821a.jpg

View from outside.

IMG_20190724_144043.thumb.jpg.9fff94d346a2e43619d1cdf7d095ba4d.jpg

Pieces let in to the outer layer.

IMG_20190724_161130.thumb.jpg.5e9f4826df9360a17fd8c0bc90936324.jpg

Inside of outer layer zinc primed.

IMG_20190724_163247.thumb.jpg.db3257eb63aac2c9b9e889206e2b625e.jpg

Missing metal of the inner layer replaced, then zinc primed.

IMG_20190724_185626.thumb.jpg.c9d13f947c36f27d2d949d43da86257b.jpg

There's a hint of more of the same on the passenger side, (a lot less of it though!) So this will be investigated another time. :)

Link to comment
Share on other sites

Got some unexpected time on this today due to having nothing to do at work. :)

Passenger side lower bulkhead/floor holes.

IMG_20190725_132636.thumb.jpg.2b5a4076c1c8c9b62f81432d86362fb4.jpg

When cut away, the layer above was in a good condition, (still had e-coat) so it was zinc primed then closed up.

IMG_20190725_141722.thumb.jpg.bbaf0671424f1113b449828ca05ce04c.jpg

Hydrate 80 applied to bare metal of surrounding areas.

IMG_20190725_170231.thumb.jpg.2a66d8dceae1e3726584a115ad23fb57.jpg

Incredibly sweaty in the shed today. :(

Link to comment
Share on other sites

Only had a couple of hours for this over the weekend - made a start on stripping the chassis legs.

IMG_20190728_170618.thumb.jpg.dd36d1bb30f3071321dc7c05204a3d54.jpg

After getting fed up with painfully slow progress, I switched to the inner wing for some instant gratification.

IMG_20190728_170324.thumb.jpg.cfe4377d93e45139c054b8ea841b7aef.jpg

Found one small area needing a welded repair (on the inner wing, in line with the front of the turret ^^^) which I'll address next time.

Link to comment
Share on other sites

New wire wheel acquired Saturday afternoon, then put straight to work on the passenger side inner wing.

IMG_20190804_123525.thumb.jpg.7d0ad8dbb584654ddb5927bed7e9ece9.jpg

Cleaned and treated on this afternoon.

IMG_20190804_145251.thumb.jpg.779c839d2730a15d4bc2c58740110822.jpg

Having a look around the engine bay (really not looking forward to bare metalling this :( ) I noticed a bit of car pox in the front cross member.

IMG_20190804_150905.thumb.jpg.96ad0606636f619b42ed4829fcae7bd4.jpg

Cut out the pox, and cleaned up the strengthener behind it.

IMG_20190804_154524.thumb.jpg.c7a4975242129087051f1175b57fd587.jpg

Welded in a piece of fresh metal to fill the hole.

IMG_20190804_160950.thumb.jpg.40d2563fc48c2d8f64a1737489a89198.jpg

Cleaned back as best as I could until my finger sander comes back from a mate.

IMG_20190804_162205.thumb.jpg.6ddb474580efe9a2143c4856b3001bfb.jpg

Back to the joy of paint/rust/crud removal next. :)

Link to comment
Share on other sites

No actual work done on the car today, but during a bit of a tidy up I got shut of a load of crispy metal removed over the last few months. All the biggest bits are long gone, but theres still a reasonable amount of scrap metal gone to the weighing in skip.

IMG_20190805_154351.thumb.jpg.2453fb2555907a035fd677aa0a210a0e.jpg

Also a new gallon of thinners was bought this afternoon so I can clean all the filth out of the engine bay in preparation for the last bout of wire wheel action.

Link to comment
Share on other sites

4 hours ago, vulgalour said:

I continue to be amazed at how not-crumbly this usually crumbliest of Vauxhall offerings is, and your dedication to cleaned up and preserving it all.

Theres definitely been a lot less metal needing replacement than there could have been. It needed saving, and I want to make as good a job as I can to help it to last - I'd be gutted if all that new steel were to start rotting again in a few years time.  :)

I managed to grab a bit of time for this on the way home today, and got stuck in to the engine bay. Its pretty fiddly, but a lot less unpleasant than the underside was.

IMG_20190806_182534.thumb.jpg.a9168c905828e8a51069440ef7e348bc.jpg

Hopefully I'll have it all stripped in a couple of weeks, then I can start getting some paint and seam sealer on there.

Link to comment
Share on other sites

Not going to be getting any time on this for a week or so now, but managed to grab a wee bit this afternoon. Driver's side inner wing got a couple of coats of Hydrate 80.

IMG_20190813_183252.thumb.jpg.50b4cddecf3a53596d0fed7a4319339b.jpg

Then made a start on removing paint and rust from the front crossmember.

IMG_20190813_182917.thumb.jpg.a87fc35f776a9e8f1fea44824144e0fa.jpg

The slam panel + front valance strengthener panel will be next on the list, followed by the passenger side inner wing. Not a huge amount of wire wheeling remains. :)

Link to comment
Share on other sites

Got a bit more done over the last couple of days - finished up stripping the underside of the slam panel (seen here before cleaning the orange dust off prior to treating with the Hydrate 80)

IMG_20190821_164753.thumb.jpg.4da26b65ba6cd13e57d2ef2d39e58c17.jpg

Underside of slam panel cleaned + treated.

IMG_20190822_175648.thumb.jpg.df5befb655aff788e0bba494df494178.jpg

Top side of slam panel also treated.

IMG_20190822_183047.thumb.jpg.cba7334cfb346afcbea06b09684308ea.jpg

I'll get the rest of the front bits treated next time. Because the front valance still needs to be welded on, the strengthener must have weld through primer on the parts which will take the plug welds. The rest of it will be treated with Hydrate 80.

Link to comment
Share on other sites

Cheers Dan! Plan at the moment is to keep it the original colour. :)

All remaining bare metal now treated.

IMG_20190824_164823.thumb.jpg.a38c89ca7ec9d11d1d5608ec83ec6627.jpg

IMG_20190824_165047.thumb.jpg.c36be5e1e4a5fbc4809ed0ae34871320.jpg

Started preparing the front valance for going on, first stripping it back to bare metal.

IMG_20190824_164525.thumb.jpg.d4c4f4f8846f9062d3a25b07c4f69659.jpg

Then giving it a couple of coats of electrox primer.

IMG_20190824_172519.thumb.jpg.61b82a4884b71d17002176a6d83087e5.jpg

It was a bit too hot for comfort in the shed today, so may not be back for a while. It'll give me a bit of time to think of a way to attach the front end of the rollover jig once the front valance goes on.

Link to comment
Share on other sites

This is great to watch as ever. Congrats on the milestone of finishing all the bare metal.

On that front valence, what made you go straight to Electrox rather than Hydrate80? (I’m a newbie at this but have some similar work in the pipeline and am finding this thread inspirational and educational.)

Link to comment
Share on other sites

On 8/24/2019 at 8:11 PM, Skizzer said:

Fair enough!

B-H does talk a good fight about the rust prevention as well as rust conversion properties of Hydrate80, but I guess if the valance has got this far with no corrosion then it’s good for another 30 years...

It'd probably be fine just painted, but that electrox tackle is supposed to be the next best thing to galvanising.  :)

I snaffled a bit of time this evening to make a start on the passenger side of the engine bay - once the shed had cooler down a bit. The battery tray was hit first. 

IMG_20190825_114648.thumb.jpg.a236fca988cae7830d6d7a65c2788562.jpg

There was still plenty of time left, so I just carried on until hunger got the better of me. (about an hour!) 

IMG_20190826_185009.thumb.jpg.ae35a0673e805ace2011122b5bff6a89.jpg

Not sure If I'm gonna finish the engine bay or stick the front valance on next, stay tuned! 

Link to comment
Share on other sites

A few short sessions during the week sees this side mostly stripped now. 

IMG_20190830_192118.thumb.jpg.4142e0c00669e3aca55e7117a0ff2972.jpg

I have a decent amount of time to get this finished off tomorrow - and it'll probably take most of the day as this side is by far the fiddliest area of the whole car. Major milestone imminent! :)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...