costadelglosta Posted October 13, 2016 Share Posted October 13, 2016 Hi shiters I've hit a problem with my 2.0 pez turbo XM after reassembly of the engine with a good skimmed head. Rough idle and EML on led me to do a compression check and the results were depressing; 3 cylinders in the high 90s psi but one at 62 psi. So cylinder one is looking borked but normal oversize pistons are not available, just Germanic forged racing jobs at £500 plus. So I'm thinking about having the cylinders bored and sleeved back to standard. Anybody had any experience of this both cost wise and durability wise? Link to comment Share on other sites More sharing options...
barefoot Posted October 13, 2016 Share Posted October 13, 2016 Yes. My 944S dropped a piston ring, scoring the bore.The other three were still within tolerance even at nearly 300,000 miles so rather than re-bore the whole block, just the one was bored & sleeved.From memory it was about £130 or £170 - a mere fraction of the cost of all the work that was done. The engine is running like it's brand new but it's probably only done about 7/8,000 since the work so I can't comment on longevity yet. Link to comment Share on other sites More sharing options...
andy18s Posted October 13, 2016 Share Posted October 13, 2016 Sure its not a valve leaking? Any sort of damage to the bore? Have you had all 4 measured to be sure? Link to comment Share on other sites More sharing options...
Eddie Honda Posted October 13, 2016 Share Posted October 13, 2016 but normal oversize pistons are not available, They're still (well the dished ones) on the Mahle catalogue. RGX or RGY? circa 60 quid a pot. Link to comment Share on other sites More sharing options...
steveo3002 Posted October 13, 2016 Share Posted October 13, 2016 could be a stuck ring? was shocked how gummed up and stuck they were on a engine i took apart which was probably an ok runner im far from an expert but would one bore wear out and not the others ? ...look at the valves /rings first Link to comment Share on other sites More sharing options...
Bren Posted October 13, 2016 Share Posted October 13, 2016 Thorough check of all the top end components before you condemn the bottom end. I remember a guy on youtube showing how easy it was to get the liners out of a RV8 - heat up in oven then push out. Link to comment Share on other sites More sharing options...
M'coli Posted October 13, 2016 Share Posted October 13, 2016 Thorough check of all the top end components before you condemn the bottom end. Hi shiters I've hit a problem with my 2.0 pez turbo XM after reassembly of the engine with a good skimmed head. I'm fairly confident that the OP has checked the top end as being good... Link to comment Share on other sites More sharing options...
DodgeRover Posted October 13, 2016 Share Posted October 13, 2016 Yes had a liner fitted to a Fourtrak after it broke a rod and made a mess of the bore, cost about £100 ish maybe a bit less, went back to standard bore size. Link to comment Share on other sites More sharing options...
pshome Posted October 13, 2016 Share Posted October 13, 2016 Try these guys, if they don't have your piston(& rings) they will make it for you. http://www.aprotec.fr/ Prices are very reasonable, i paid 300€ for a set of 4 sleeves, pistons and rings for my 504 GL not so long ago. http://www.aprotec.fr/wp-content/uploads/2016/03/AP08_pistons.pdfhttp://www.aprotec.fr/wp-content/uploads/2016/03/AP08_coussinets.pdf costadelglosta 1 Link to comment Share on other sites More sharing options...
RayMK Posted October 13, 2016 Share Posted October 13, 2016 I thought the rule of thumb ok figure for a compression test on a petrol engine was 100psi or better and most modernish engines seem to give 125psi or thereabouts. I suppose 'high 90s' is almost there, but would hesitate to spend too much fixing the low reading bore if the others were well past their best. billyboy406v6 1 Link to comment Share on other sites More sharing options...
alf892 Posted October 13, 2016 Share Posted October 13, 2016 Best carry out a cylinder leakage test before going any further.......saves guesswork Link to comment Share on other sites More sharing options...
Stanky Posted October 13, 2016 Share Posted October 13, 2016 No, No NO! Clearly the answer is to use the magic gloop that Quentin Wilson endorses in the back of the clasic car mages that makes your 500k engine just like new because it contains PARTICLES and as everyone knows that adding magic particles will restore compression to better than new. cros, brickwall, The Moog and 5 others 8 Link to comment Share on other sites More sharing options...
Parky Posted October 13, 2016 Share Posted October 13, 2016 sand is particles - that would work surely? The Moog, mat_the_cat, costadelglosta and 1 other 4 Link to comment Share on other sites More sharing options...
costadelglosta Posted October 14, 2016 Author Share Posted October 14, 2016 Sure its not a valve leaking? Any sort of damage to the bore? Have you had all 4 measured to be sure?The head was freshly skimmed and overhauled so unlikely. I'm thinking storing the block sans head in my horrid damp asbestos garage is the culprit. Link to comment Share on other sites More sharing options...
costadelglosta Posted October 14, 2016 Author Share Posted October 14, 2016 They're still (well the dished ones) on the Mahle catalogue. RGX or RGY? circa 60 quid a pot.I've checked the Mahle catalogue and they are indeed listed. Question is are they available? XU10J2TE was a popular turbo conversion for the 205 gti crowd and all their forums suggest pistons are unavailable. I will follow this up. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now