Jump to content

1975 Ford Granada Coupe - Lots & lots of tinkering


TripleRich

Recommended Posts

Fantastic work, a pleasure to watch it come together and to see you maintain your patience and care when I'm sure there must be the temptation to rush and finish it off.

You're more than justified in taking a break - it's remarkable how you've stuck at this after doing the same thing throughout your working week.

Link to comment
Share on other sites

Thanks for all the comments and interest guys.  It really helps keep the motivation going knowing there's a group of people interested in seeing the exploits of a crazy bloke who appears to live at work.  I'm looking forward to getting out and about with it next year.

Link to comment
Share on other sites

It's been quite a while but it is all coming together now. These are such lovely looking cars and you just don't see them anymore. 

The standard of your work and attention to detail is stunningly brilliant.  It is going to be even better than when it rolled off the production line.

Fabulous. 

Link to comment
Share on other sites

  • 2 weeks later...
On 9/8/2019 at 5:26 AM, TripleRich said:

Still have the sills, rear window frames and back panel to do.  Once those are done the paint will have had plenty of time to fully cure ready for a flat & polish.

20190907_180639.thumb.jpg.a959150199976a443ccb3635e657d1dc.jpg

Did you flat & polish before you started reassembling the outside trim, grille, lights etc...?

I can't recall you saying you did and to my untrained mind, I would have thought it would be better to do the flat & polish before the reassembly?

Absolutely love the work you have done by the way, you must be well chuffed to have got to this point and eager to FINALLY get it on the road!

Link to comment
Share on other sites

I've made some more progress over the past two weeks.  Few more bits have made their way onto the car and I've started polishing the paintwork.

I've not polished the paint until now for two reasons...

  • I didn't have the balls to take 1200 grit sand paper to my paint job
  • I needed to perform one or two additional bits of paint correction and they are now complete. (I missed a nasty ripple in one of the rear wings and needed to fix it).  Tried living with it for 2 months and couldn't stop looking at it all the time. 

First up the washer bottle bracket which was very rusty/damaged has been repaired and painted.  I've already polished what I can of the engine bay.  When new the finish in here was very poor and it's one of the reasons for all those scabby Ford engine bays years later.  I've got a good coat of paint in here and it's shiny so I'm already beating the original factory.  I will continue to hand polish various areas under here as and when I get the motivation.

20200104_153431.thumb.jpg.41949a7e54d8b6dba91d5d01da333ade.jpg20200104_172327(0).thumb.jpg.7d240de8820dd7f95e9d4735e5a01e06.jpg

Next I've fitted the rear windows.  This is probably the worst bit of design on the whole car.  The window is held in by the pop out catch at the rear and two very small bits of metal on the B post.  With the window popped open it eventually falls out while driving so they will remain shut from now on!  This is a well-known fault with the face lift coupe.

20200104_165002.thumb.jpg.edacb3f68282028dee0e5f9c83f949c3.jpg20200104_171605.thumb.jpg.3beef4aa7793f3659f108dee4fa1be4c.jpg

I've also fitted the remaining trim pieces inside the rear of the car.  Starting to look quite nice in here now.

20200104_171914.thumb.jpg.0c93d4a70a4419917a82512f24dcfef6.jpg20200104_171922.thumb.jpg.c46d234ded88d0f83c0b11e4eaa0d088.jpg

Polishing the paint is a slow and scary process.  I've never done it to this level before but it won’t polish itself so I've made a start.  All the bits I've put on the outside of the car so far have been chosen because they don't really get in the way of the process.  There is nothing fitted to the sides of the car so I have access for polishing.  

Here you can see the finish as it is off the gun.  Deep shine but plenty of orange peel and when you start looking there is a fair bit of dirt in places.  I expected this as I'm a novice painter.

20200111_110900.thumb.jpg.fa4fade0fc0da1d4a8062f178156980e.jpg

First thing to do is use a de-nibbing tool to remove any spots of dirt & dust.  I'm using 2000 grit on the tool as it's what’s in stock.  You end up with loads of little dull spots after completing this.

20200111_110918.thumb.jpg.51d5f96c9b595b650db3f0115a4897df.jpg

Next I use 1200 grit paper on a DA with a soft interface pad.  This takes down the orange peel and also removes any small bits of dirt and dust.  Be careful of the edges!

20200111_113809.thumb.jpg.51506f95f91e3e9b441a1906bf7abc44.jpg

Next I move to 1500 grit on the same tool and sand until I have a flat matt finish.  All the time I'm terrified of seeing primer but if you study the picture I'm really removing only the very top surface of the paint.  There is no danger of rubbing through provided I stay off the edges and stick to the method.

20200111_113820.thumb.jpg.daf18eac4cc40e7d34ba1935b20667dd.jpg20200111_114953.thumb.jpg.3154a14dc1eb630de9714c40c27c1f2b.jpg

Next I move onto 3000 grit 3m Trizact disk.  This removes all the 1500 grit scratches and starts to move us back towards a shine.

20200111_120508.thumb.jpg.d4e9159813b2f9764af40dd68c773503.jpg

After this I should have gone to a 6000 grit Trizact but I didn't have any.  I've ordered some so will have a go next weekend.  In the absence of those I moved to polishing using 3m green & blue pads/compounds and a decent polisher.

20200111_132906.thumb.jpg.010299ad024334bcf2c0d1451f78a40e.jpg20200111_134410.thumb.jpg.2a1b05b1f96861d17f71796fd824ab0c.jpg

Not bad for a first go.  I didn't make any major mistakes but due to lack of confidence I've not fully removed the orange peel near the edges and a few small areas.  I also needed to spend more time on the polishing stage.

I'll revisit the again with 1500 and follow up with both Trizact disks.

Here's a comparison.  Before on the left and after on the right...

20200111_110900.thumb.jpg.fa4fade0fc0da1d4a8062f178156980e.jpg20200111_131038.thumb.jpg.f4b863035f79cddf1f05d11148937d09.jpg

Will take me a few days to complete this, nice boost to confidence as I didn't mess it up!  Was more worried about this bit than the actual painting.

Link to comment
Share on other sites

6 hours ago, TripleRich said:

I've made some more progress over the past two weeks.  Few more bits have made their way onto the car and I've started polishing the paintwork.

I've not polished the paint until now for two reasons...

  • I didn't have the balls to take 1200 grit sand paper to my paint job
  • I needed to perform one or two additional bits of paint correction and they are now complete. (I missed a nasty ripple in one of the rear wings and needed to fix it).  Tried living with it for 2 months and couldn't stop looking at it all the time. 

Lol..answered my question..good luck with the rest of the polishing..it looks like it will come up great?

Link to comment
Share on other sites

3 hours ago, Austat said:

Great work TripleRich! I have been interested in this restoration for a while as my late Grandad had a Granada (or a Consul Ghia, unsure) as a company car back in the mid-70's. Sadly, I doubt that APU 642L still exists anymore.

 IMG_0334.thumb.jpg.ed43e96dc76f8884c4a1c382bf88ac0f.jpg

That's a lovely picture, I particularly like the hubcaps, which incidentally mark it out as a Consul. There was never a Consul Ghia so this is either a 2000 V4 or 2500 V6 . That and the 3000 GT was the entire Consul range ( in the UK ) 

Link to comment
Share on other sites

3 hours ago, Jenson Velcro said:

This is looking absolutely fantastic and has been a great read to date. I would be terrified of using the car when completed though as I would be afraid of marking it after all the hard work.

I try not to get worried about what might or might not happen out on the road.  If something does happen I've got plenty of spares, half a tin of paint and some tools.  Fixing a dent, scratch or mark is easy enough as it's a solid colour.

Link to comment
Share on other sites

7 hours ago, NorfolkNWeigh said:

Great work TripleRich! I have been interested in this restoration for a while as my late Grandad had a Granada (or a Consul Ghia, unsure) as a company car back in the mid-70's. Sadly, I doubt that APU 642L still exists anymore.

Nice car, would have impressed the neighbours back in the day!  Looks to be a Consul L as it has a few options like the vinyl roof, mirrors and the Consul specific grille.  GTs had Granada grilles and base models wouldn't have had the vinyl roof so it's probably an L.

Link to comment
Share on other sites

On 1/17/2020 at 9:38 AM, TripleRich said:

Nice car, would have impressed the neighbours back in the day!  Looks to be a Consul L as it has a few options like the vinyl roof, mirrors and the Consul specific grille.  GTs had Granada grilles and base models wouldn't have had the vinyl roof so it's probably an L.

 

On 1/17/2020 at 1:50 AM, NorfolkNWeigh said:

That's a lovely picture, I particularly like the hubcaps, which incidentally mark it out as a Consul. There was never a Consul Ghia so this is either a 2000 V4 or 2500 V6 . That and the 3000 GT was the entire Consul range ( in the UK ) 

 

On 1/17/2020 at 1:59 AM, danthecapriman said:

It was a 2.5 and died in 1983 by the looks. Bloody nice car though!

Thanks guys for the info, I was unsure whether or not it was a Consul or a Granada, so it's good that there's more info on the car. My dad really liked this car as a kid back in the mid 70's, especially because he was a fan of The Sweeney.  He also recalls that my Grandad had a Datsun saloon at one point as a company car, describing it as one of the higher end spec models (so possibly a 240K or a C130). 

I have a question regarding the Consul/Granada cosmetics, what is the difference between the LHD headlights and the RHD headlights?

Link to comment
Share on other sites

Got quite far flat & polishing the car today.  The bonnet, boot lid and drivers side are now complete.  About 6 hours of work.

First I spent some more time on the bonnet and got it looking better.  Pleased that most of the surface imperfections on this panel have now gone.

20200118_095546.thumb.jpg.f402b8e4a5007b2c3b5cc85c732a96f6.jpg

Next up was the front wing.  The shape of panel means I have to take more care and use a combination of machine & hand polishing.

First pass with 1200 to take the top of the orange peel off.  I then use the finish below as a guide coat for the 1500 grit stage.

20200118_103201.thumb.jpg.cd24401cc83371463a95278731c77aba.jpg20200118_104740.thumb.jpg.f416ac0ac9c4fb08692293c6536e4e40.jpg

Second pass with 1500

20200118_104743.thumb.jpg.2d175e9c06d7700a2e1e06c6b9c630a7.jpg

3000 grit trizact disk

20200118_110505.thumb.jpg.94bba3d1cdb6fa7a742fca0fc218c8f9.jpg

6000 grit trizact disk 

20200118_111512.thumb.jpg.f46312d36095da399e39b1e93a38b3b5.jpg

Polish with 3M green mop & compound

20200118_113438.thumb.jpg.65f21a7a71ff2bbcdf6b5ae79f40b50c.jpg20200118_113621.thumb.jpg.de39d96fd21ff4aed1895ee9414e1173.jpg

20200118_113633.thumb.jpg.1beafebb1cf620c48835537f921dcef8.jpg20200118_113643.thumb.jpg.ef6620ef98ef6d5563229e2d257d273c.jpg

Worked my way down the car and did the door and rear quarter.  The quarter took a long time, its huge!

20200118_124551.thumb.jpg.381f570b4ea197df211591e259d09c23.jpg20200118_134656(0).thumb.jpg.fcc538a0616f157a8ced7848eb45a8f3.jpg

20200118_141049.thumb.jpg.63001355907fd88ddbedfc102ccc1251.jpg20200118_141110.thumb.jpg.f64caa2ba73486d773e167f0191ac693.jpg

Then the boot lid

20200118_154130.thumb.jpg.75d5b7777d48971859b330e3e0d4059e.jpg20200118_154141.thumb.jpg.9954d51830756ecfd5339b5520a46dd6.jpg

That completes the drivers side.  I'll do the other side next week.

20200118_171206.thumb.jpg.e1b8d4e214a6ebf577cd7d4a793726fd.jpg20200118_171218.thumb.jpg.424ecbe8638fcad6fe5d6ebb07d26a3e.jpg

Very pleased with the result.  Removed most of the orange peel & surface imperfections in all the panels I treated.  Looks like a professional job now, amazing what you can do with the right equipment.  There were a few bits I was worried about but they just polished away.  Good learning experience all round, looking forward to the other side.

20200118_141622.thumb.jpg.ac6d087c02a0e991277731cdc40f1564.jpg

Link to comment
Share on other sites

Just spent an hour or so over the last day catching up with this project, what a brilliant read! On top of the work put into the car, there must be a fair bit of effort associated with photographing progress then uploading and typing out the commentary, really good that you’re going to all this trouble and sharing it with us. 

Link to comment
Share on other sites

My favourite thread on here for sure, absolutely loving the work and learning loads too.  Tempted to hand paint a car one day, be interesting to see if using similar techniques will get a similar finish.

Quick question though - what sort of paint did you use?  2k with a clear coat on top?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...