Jump to content
dome

Domes shonky autos-Kangoo 182 on the road!

Recommended Posts

It all started with a message from a mate last week. Want a free car? A friend of his was needing rid.  


 


You can guess what my answer was.


 


I was sent this photo and told it had early stages of head gasket failure.


 


post-7629-0-44606600-1463604868.jpg


 


At least I new this one was broken. Whether or not it would make it home or not was a different matter...


 


Fast forward to tonight. Supplies collected and off we went.


 


post-7629-0-80431300-1463604916.jpg


 


Transport of choice. My mate is a shiter, he just doesn't know it yet...


 


On to the beast in question.


 


post-7629-0-19913400-1463604906.jpg


 


A 1.8 (it would be wouldn't it?) Freelander Serengeti. Phwoooar.


 


Initial thoughts under the bonnet-no obvious signs of being fucked about with, however no coolant in the expansion bottle and the dipstick was dry. No signs of Mayo anywhere.


 


Topped up fluids and fired it up. It was a bit tappy which is to be expected with no oil but quietened down. Let it warm up, bled it a bit and added some K Seal. I had a 25 mile drive home so better safe than sorry. I also left the expansion cap off and set the heater to max and off we set. Brakes were stuck on but soon freed off.


 


It only bloody made it! I babied it, not taking it above 3000rpm but when I got home it hadn't used any coolant. Gauge stayed bang in the middle and the heater was blowing red hot all the way.


 


I put the expansion cap on and let it run for a bit and it behaved itself. 


 


Back home. Apologies for the pics, it was getting dark. Probably for the best.


 


post-7629-0-56422500-1463604876.jpg


 


post-7629-0-41867100-1463604885.jpg


 


post-7629-0-18514700-1463604895.jpg


 


It's a bit rough, stinks of fags and only one electric window works. It's had the prop disconnected so is 2wd. It drives OK, think there may be an engine mount gone and there something knocking front end wise. But it was free...


 


Plans? Clean it and work out what's wrong with the engine. The boy I got it from reckoned it had had the modified head gasket done before he got it, there are no receipts though...


 


Then smoke about for a bit and flog it. Probably to buy something equally broken. I don't get out much.


post-7629-0-44606600-1463604868_thumb.jpg

post-7629-0-56422500-1463604876_thumb.jpg

post-7629-0-41867100-1463604885_thumb.jpg

post-7629-0-18514700-1463604895_thumb.jpg

post-7629-0-19913400-1463604906_thumb.jpg

post-7629-0-80431300-1463604916_thumb.jpg

Share this post


Link to post
Share on other sites

Well, so confident* was I in my new steed that I decided to brave the commute in it today-also becauee it's only insured til tonight and it gives me a chance to put some more miles on it and hoover it/check tyre pressures etc. I gave it a quick wash and it came up not too bad. I even refitted the expansion cap after checking the coolant-no loss in the 25 miles last night. Quick wash this morning as it was manky and here's the passenger side for the doubters ;)

post-7629-0-98866500-1463650996_thumb.jpg

 

 

Share this post


Link to post
Share on other sites

Well, so confident* was I in my new steed that I decided to brave the commute in it today-also becauee it's only insured til tonight and it gives me a chance to put some more miles on it and hoover it/check tyre pressures etc. I gave it a quick wash and it came up not too bad. I even refitted the expansion cap after checking the coolant-no loss in the 25 miles last night. Quick wash this morning as it was manky and here's the passenger side for the doubters ;)

DSC_0045.JPG

Dude, how the mighty have fallen.. softroader ftl:(

Share this post


Link to post
Share on other sites
Guest Hooli

When you say the modified head gasket has been fitted, which one? there were a lot of revisions. I think the final one included a new stiffer ladder which fits in the sump for the head bolts to lock into.

Share this post


Link to post
Share on other sites

When you say the modified head gasket has been fitted, which one? there were a lot of revisions. I think the final one included a new stiffer ladder which fits in the sump for the head bolts to lock into.

 

I have no idea and no bills or history for the car so your guess is as good as mine...

Share this post


Link to post
Share on other sites

Started trying to get the stink of fags out of this thing. Knackered drivers side regulator and a chain smoker=filth.

 

 

It'll need done again. And again. Still stinks inside. Any tips for getting rid of the smell of fags?

 

Will try and get the inlet manifold gasket changed this weekend and give it a coolant flush and proper bleed if I get the chance, the Locost is the priority though if I get the head back for it...

Share this post


Link to post
Share on other sites

Get the front seats out and have a good hoover underneath. Headlining takes a lot of stink too.

 

I've found steam cleaners to be pretty effective. Just watch out / becareful on stuff like headliners.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Peter C
      Woke up this morning, had a little time before I had to leave the house for work, had a quick look at what’s new for sale on Retro Rides and saw an ad for a W124 200E manual, located 15 miles from home. I had no intention of buying a car today but I had to have it! I called the seller and arranged a viewing.
       
      Faults:
       
      2 x rusty front wings (TADTS)
      1 x rusty rear arch
      Needs a polish
      Tracking is out because new track rod end was fitted for MoT
      Engine has oil leak/s
       
      Good points:
       
      It’s a W124 200E!
      5 speed manual transmission
      New clutch
      Brand new MoT
      Superb MoT history
      4 x as new Continental tyres
      Last owner for 15 years, her husband before that for 4 years
      Very tidy MB-Tex interior
      Drives well
      All electrics work
       
      The dealer kindly delivered the car to my house but I managed a pez station shot on route:
       

       
      Plans:
       
      Remove front wings, cut away rust and apply plenty of wob.
      In-situ similar repair for rear arch
      Clean and polish
      Service engine
      Adjust tracking
      Leave patina and enjoy the car as it is
       
      I will update this thread once progress is made.
       

       

       

       

       

       

       

       

       

       
      Hopefully these two will become good friends.
       

    • By PhilA
      Well, here we go again. I bit the bullet and bought me this.
       

       

       
      It's still up at the lot right now, there will be a miniature Collection Thread embedded in this thread when I go fetch it. Hopefully if the weather's good, that'll be this weekend.
       
      So, what is it?
       
      As the title suggests, it's a 1951 Pontiac Chieftain.
      It's got a flat-head straight eight hiding in the engine bay, 4.4 litres of it. It's bolted to a 4-speed Hydra-Matic Drive gearbox. No torque converter on this one, just a fluid coupling. 116 horses at a screaming 3700 RPM, 240lb/ft at 2000. It idles at 375 RPM. Redline just shy of 4k.
      Did I mention it's quite big? Sixteen foot eight from end to end and it seats six people in comfort. Every door has a quarter-light, too. Comfort is provided by properly sized tyres and (quite surprisingly for the age of it) double independent wishbone front suspension. Steering is via worm/wheel steering box so is moderately direct and the brakes are hydraulic drums all round. Modern and scientific!
       
      It's an honest example; looks to have had a "restoration" about 15-20 years back and the rust is coming through the seams and filler. The bottoms of the door skins have gone, the bottom of the A-pillars have gone (the front doors, on a single hinge a piece still open and close with one finger!) And it's got a couple holes and blebs in all the places you would expect.
      Not much electrical works. It needs to be completely rewired because someone has "converted" it to 12V. Thankfully it was originally negative ground so that's a good start. Gauges and such can be driven from a 6V bucking converter.
      Engine has had some work done on it- starts and runs nicely with very little greb coming out of the exhaust. It's got a few gaskets that need replacing and the tappets need some major adjustment, the gearbox engages gears correctly, the steering is okay but has a lot of slack in the center and the brakes work well, dont sink or feel spongy but need adjustment.
       
      More to come. I'll post up more pictures when I get it home.
       
       
      --Phil
    • By Zelandeth
      Well I've been meaning to sign up here in forever, but kept forgetting. Thanks to someone over on another forum I frequent poking me about it recently the subject was forced back into my very brief attention span for long enough to get me to act on the instruction.

      I figure that my little varied fleet might bring you lot some amusement...

      So...we've got:

      1993 Lada Riva 1.5E Estate (now fuel injected, as I reckon the later cars should have been from the factory...).
      1989 Saab 900i Automatic.
      1987 Skoda 120LX 21st Anniversary Special Edition.
      1985 Sinclair C5.
      2009 Peugeot 107 Verve.

      Now getting the photos together has taken me far longer than I'd expected...so you're gonna get a couple of photos of each car for now, and I'll come back with some more information tomorrow when I've got a bit more time...

      Firstly...The Lada. Before anyone asks - in response to the single question I get asked about this car: No, it is not for sale. Took me 13 years and my father's inheritance to find the thing.


      Yes, it's got the usual rusty wings...Hoping that will be resolved in the next couple of months.

       






      Next, a proper old Saab. One of the very last 8 valve cars apparently, and all the better for it. I've driven two 16v autos and they were horrible - the auto box works sooooo much better with the torque curve of the 8 valve engine. Just wish it had an overdrive for motorway cruising...









      Next up a *real* Skoda...back when they put the engine where it belongs, right out the back. In the best possible colour of course...eye-searingly bright orange.







      Seat covers have been added since that photo was taken as it suffers from the usual rotting seat cloth problem that affects virtually all Estelles.

      Then we have possibly the world's scruffiest Sinclair C5...



      Realised when looking for this that I really need to get some more photos of the thing...I use it often enough after all! We have a dog who's half husky, so this is a really good way of getting him some exercise.

      Finally - again, I really need to take more photos of - we have the little Pug 107.



      Included for the sake of variety even if it's a bit mainstream! First (and probably to be the only) new car I've bought, and has been a cracking little motor and has asked for very little in return for putting up with nearly three years of Oxford-Milton Keynes commuter traffic, before finally escaping that fate when my housemate moved to a new job. Now it doesn't do many miles and is my default car for "when I've managed to break everything else."

      I'll fill in some more details tomorrow - I warn you though that I do tend to ramble...
    • By strangeangel
      I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.
       
      So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.
       
      Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.
       
×
×
  • Create New...