Jump to content
strangeangel

Strangeangel's Citroënic Shenanigans (featuring the Autoshite BX, Ami Break and some bikes) 22/2 Aixam spares blag!

Recommended Posts

I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.

 

So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.

 

Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.

 

Share this post


Link to post
Share on other sites

Height lever problem: My XM had the same problem with the height lever except it wouldn't go to the lowest setting. Someone suggested that the runner/guides under the car that the shaft runs through can become clogged up with shit and that a clean and lube would be the first step in trying to solve it.

 

RE the tyres: You could probably get away with the 185/65/14's but your speedo will under read by -1.59% plus whatever discrepancy they have from the factory. In other words 30mph = 29.52mph and 60mph = 59.04mph plus whatever the original discrepancy is. Not ideal but better than it reading slower than you are actually going.

Share this post


Link to post
Share on other sites

You don't want to go too wide on the wheels or tyres, 5.5J best, you might get away with 6 if lucky. They foul on the rear arms, especially if the latter are leaning a bit. Seem to recall I just scraped by with 195/60/14s but 65s (or less) are better.

Share this post


Link to post
Share on other sites

I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.

 

So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.

 

Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.

The height lever always was stiff, just needed a good tug to get it locked in position.

Share this post


Link to post
Share on other sites

You don't want to go too wide on the wheels or tyres, 5.5J best, you might get away with 6 if lucky. They foul on the rear arms, especially if the latter are leaning a bit. Seem to recall I just scraped by with 195/60/14s but 65s (or less) are better.

It was running on 6J with 195/60 14 and in spite of the rear arches being trimmed it was hard to get them on and off. Nothing seemed to rub while being driven though.

Share this post


Link to post
Share on other sites

Check the linkage at the rear (it's all simple mechanical levers, rods and joints) and clean/grease. The handle in the car can take a bit of a pull to stick it in max height, but not to the point of excess. Is that clear as mud?

 

I think the GTis had 185/60/14s on 6" rims, when I ran them they were £200 bangers so used whatever they came with, but I seem to remember the sweetest combination was a car with 175/65s fitted.

 

Any pics?

Share this post


Link to post
Share on other sites

Warning. Do not reach or crawl under a BX unless it is on stands. But yes, the linkage needs greasing. It shouldn't be too stiff.

 

Regarding level, if the yellow marker is resting on the top of the globe at normal height, it's probably not too far off.

Share this post


Link to post
Share on other sites

BX's are ace - and well bought that man.

 

The HP set up is quite easy to live with once you get your head around it and even stripping the doesur (sic) valve isnt the end of the world - somewhere on the internet are some very informative pictures from @Vanny of this parish ( and the BX Project) who has stripped and refurbed one. agreed about having a quick look and lube underneath - but only with the car on axle stands - I really cant stress this enough as Ive had one crush a 2.5L tin of bitumen in seconds when it dropped ( resulting in a North West "Face of Christ" on the driveway for several months). 

 

Ive had 195's on one of mine and apart from needing to slightly modify the rear spats with a piece of wood all was well, but if the rear arm bearings are shagged they will rub.

Share this post


Link to post
Share on other sites

Height corrector - It's okay, just needs a firm tug to get to the high position.

 

Wheels - It did run 165s when it was on steels. 195 you can get away with on the front (bought some in error but it was a shame not to use them) and 185s will go under the rear but will rub when on lowest setting. Rear arms lean a nib but don't affect the clearance.

 

DO NOT rely on the suspension to get under the car. The rear goes down pretty quickly (an hour or two) but the front stays up pretty well.

 

I know this machine pretty well.

Share this post


Link to post
Share on other sites

Still haven't done anything about the LHM escape, largely because of doing-up-the-house type stuff, but also now that one of the 205s CV joints has shat itself the BX is officially Number One Car.

 

I did manage to discover why the throttle action was so heavy though, even with a new cable. The soundproofing under the dash had dropped down and was catching on the very top of the pedal mechanism - now fixed!

Share this post


Link to post
Share on other sites

Still haven't done anything about the LHM escape, largely because of doing-up-the-house type stuff, but also now that one of the 205s CV joints has shat itself the BX is officially Number One Car.

 

I did manage to discover why the throttle action was so heavy though, even with a new cable. The soundproofing under the dash had dropped down and was catching on the very top of the pedal mechanism - now fixed!

 

Phew. That's good, because BX's can suffer from pedal box collapse. Clutch or accelerator can fail. 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Zelandeth
      Well I've been meaning to sign up here in forever, but kept forgetting. Thanks to someone over on another forum I frequent poking me about it recently the subject was forced back into my very brief attention span for long enough to get me to act on the instruction.

      I figure that my little varied fleet might bring you lot some amusement...

      So...we've got:

      1993 Lada Riva 1.5E Estate (now fuel injected, as I reckon the later cars should have been from the factory...).
      1989 Saab 900i Automatic.
      1987 Skoda 120LX 21st Anniversary Special Edition.
      1985 Sinclair C5.
      2009 Peugeot 107 Verve.

      Now getting the photos together has taken me far longer than I'd expected...so you're gonna get a couple of photos of each car for now, and I'll come back with some more information tomorrow when I've got a bit more time...

      Firstly...The Lada. Before anyone asks - in response to the single question I get asked about this car: No, it is not for sale. Took me 13 years and my father's inheritance to find the thing.


      Yes, it's got the usual rusty wings...Hoping that will be resolved in the next couple of months.

       






      Next, a proper old Saab. One of the very last 8 valve cars apparently, and all the better for it. I've driven two 16v autos and they were horrible - the auto box works sooooo much better with the torque curve of the 8 valve engine. Just wish it had an overdrive for motorway cruising...









      Next up a *real* Skoda...back when they put the engine where it belongs, right out the back. In the best possible colour of course...eye-searingly bright orange.







      Seat covers have been added since that photo was taken as it suffers from the usual rotting seat cloth problem that affects virtually all Estelles.

      Then we have possibly the world's scruffiest Sinclair C5...



      Realised when looking for this that I really need to get some more photos of the thing...I use it often enough after all! We have a dog who's half husky, so this is a really good way of getting him some exercise.

      Finally - again, I really need to take more photos of - we have the little Pug 107.



      Included for the sake of variety even if it's a bit mainstream! First (and probably to be the only) new car I've bought, and has been a cracking little motor and has asked for very little in return for putting up with nearly three years of Oxford-Milton Keynes commuter traffic, before finally escaping that fate when my housemate moved to a new job. Now it doesn't do many miles and is my default car for "when I've managed to break everything else."

      I'll fill in some more details tomorrow - I warn you though that I do tend to ramble...
    • By BoggyMires
      Now in my mucky hands is this S Type Mondeo Lincoln. It's not like a Mondeo Lincoln  though, just uses some of the bits as it's from a time when jaguar was experiencing some 'technical' issues. 
      It has managed to hang onto the feel of a premium car but for the use of cost saving interior plastics made from the same gear that land Rover used in the discovery 2 of the same era, I know, I have one of those too! That has some BMW switches in it though.
       
      This jaag was cheap. Why did I buy it? All I wanted really was a small convertible for the summer to smoke around in, this is the polar opposite. 
      The price was good but these cars are without their expensive issues. I liked the body. It's virtually rust free, a freak of nature and it had a set of premium tyres on it which suggested it's had some money chucked at it.
       
      That's all I wanted really from it. The bolt on stuff and mechanicals are fairly easy to sort out, plus I can upgrade as I feel fit.
       
      Today I've been bonding with this machine. It's got to beat the 3 series I have as a good daily or it's out. It's going to be a tall order, the 318 is bionic!
       
      I have many miles to do in the next few months, I need a motorway cruiser auto. The odd jaunt for a few hundred miles is the 318's and my clutch legs limit!
       
      Now, this car has been owned previously by a few members on here, the work it requires is because it is a cheap car and 20 years old and has a jaguar badge on it. There are a few issues with it.
       
      As said, it has to be put into immediate service. I've owned it 2 days and it's already done over 300 miles, and will do all that again tomorrow! So let's get started!
       
      After about 100 miles yesterday, I reversed it for the first time in my ownership and when braking the noise was alarming! Had a look and the outer rear brake pad was metal on the disc. I only had another 60 miles to go!
      A phone call on the move saw a set in stock back home to be picked up. Sweet.
       
      That was yesterday, I've got a day now to change the rear pads and sort out the dropped headlamps with a couple of screws... A couple of hours it'll be Sorted... He says...
       
      WIND BACK CALIPERS! Yes, they are. My special tool? Sorry? What? No tool?
      Well, I cobbled together a bar and a pair of molies but Christ, that was messing about! I wanted to secure the caliper to the mounting to hold it still but the sliders internal thread was cross threaded on both sliders, so I had to tap them out first. It worked but not without a fight. Then my neighbour came over to have a nose at the new aquisition... Him: Morning, how you getting on"?, Me: "Shit, you haven't got a brake caliper tool have you"? Him: "Yeah, I'll go get it". 
       
      LIFESAVER!!!
       

       
      Sticky slider syndrome ^
       

       
      Fully padded up ^
       
      I took a look around under there, it's nearly all shot. Most ball joints are exposed to the elements so all need replacing but not before a decent jet wash.
       

       

       
      There's little play in the joints so all that goes on the list of parts and graft! Wheels on, I loosened and torqued all the wheel nuts around the car and done the Tyre pressures, we were running soft all round.
       
      Next was the front lights. A screw mod can be done but I took the back off the units and they were, well toast. Nothing much holding the inner lenses still at all. There was only one thing for it...
       

       
      I had readied myself for this. I got hold of a replacement lamp mounting kit with all parts made from nylon. This involved dissecting the lamp which was tough! The mounts that came out, or what was left of them were weaker than Jacobs crackers and just crumbled. To get the bumper off, the plastic under tray bolts were all seized so I had to grind them off. More knackered parts were seen. The auto box cooler has shed most of it's cooling fins, the radiator is sweating and the power steering is hemorrhaging fluid on full lock. There's also a coolant leak at the thermostat housing and there's a high pitch whine at 1000 RPM which turns out to be the alternator. More for the list.
      Still, back to the lights. I need to be able to see tonight so I took a level off the tourings lights and marked on to a wheely bin, these are pretty spot on. Then I can use the bin for the Jaags lights and I won't be far off 
       

       
      Going back together nicely it was a good time to run some tcut over the faded lenses. They need a more intense compound and a machine but will do for now.
       

       
      Looks smart yo!
       
      Then it got dark...
       

       
      I then drove 120 miles in it and drove it like it was stolen. It had it, all of it! Slight brake judder at 90 and I couldn't get the alignment done as I had no time (see above pics)
       
      So now we have to price up priorities like the knackered joints on the rear and a full service, two Goodyears and investigate the power steering leak which, I'll hazard a guess at the rack seals are fubard. 
       
      So in summary, I got a bargain barge that has it's fair share of issues, the interior quality is a bit shocking in places but when the hammer is down, none of this matters! It fits in, it can be a proper giffer cruiser with radio two on at 30mph but it'll turn into a bruiser with some oldskool hardcore at a tonne. It's come to a good home.
    • By Broadsword
      I think the Broadsword fleet has become sufficiently complicated to merit a combined thread so that gradually all new additions will appear in one place.
       
      As of Sunday 17th March the situation is interesting.
       
      Two Citoren Xantias (remember the white Xantia of Excellence is for sale people!)
      http://autoshite.com/topic/34699-w-reg-citroen-xantia-20-hdi-xantia-of-excellence-%C2%A3999/
      http://autoshite.com/topic/34596-citroen-xantia-double-madness-rust/page-2
       
      A turquoise XJR6 pending overdue-collection (need that gone now!)
      http://autoshite.com/topic/34003-jaguar-xjr6-double-madness-double-sold
       
      An XJS 3.6 manual project which will get in high gear soonish. Wont be a keeper but will be fun getting it back to something presentable. Drivers fantastic!
      http://autoshite.com/topic/34664-jaguar-xjs-36-manual
       
      A Range Rover P38, which is turning out to be really rather good.
       
      And to mix things up even more I'm off on a collection caper today. Had first refusal on it and was expecting it to come around in a year, but things soon changed and no way was I going to pass up on it. It may well render the second Xantia redundant as I've got a really good feeling about this motor.
       
      In the meantime here are some snaps of the Range Rover. As usual it was a car I said I would probably never buy due to their reliability*. I have said the same of Jag XJR, XJS, XK8 and I have had all of those now. Basically the moment I declare buying a particular car is impractical or improbable, I end up buying one.
       
      Things to note on the P38. It's a nice colour with tidy body. The EAS has been removed. It runs and drives lovely and it doesn't have enough electrical problems to hinder progress. The main one is the driver's side window not working, but that should be fixable. I've tried changing the outstation, that didn't fix it. Might be wiring under the seat. Other than that I bought it and took it for an MOT the very next day, and it passed. Since then it had what seemed like a battery drain, but since unplugging the RF thingy for the remote locking and putting on a proper lead-acid battery, which the car can actually charge, unlike the modern lead-calcium batteries, it has been perfect. I will treat it to a full service soon.
       
      Stay tuned for the latest collection later today!



    • By Peter C
      Woke up this morning, had a little time before I had to leave the house for work, had a quick look at what’s new for sale on Retro Rides and saw an ad for a W124 200E manual, located 15 miles from home. I had no intention of buying a car today but I had to have it! I called the seller and arranged a viewing.
       
      Faults:
       
      2 x rusty front wings (TADTS)
      1 x rusty rear arch
      Needs a polish
      Tracking is out because new track rod end was fitted for MoT
      Engine has oil leak/s
       
      Good points:
       
      It’s a W124 200E!
      5 speed manual transmission
      New clutch
      Brand new MoT
      Superb MoT history
      4 x as new Continental tyres
      Last owner for 15 years, her husband before that for 4 years
      Very tidy MB-Tex interior
      Drives well
      All electrics work
       
      The dealer kindly delivered the car to my house but I managed a pez station shot on route:
       

       
      Plans:
       
      Remove front wings, cut away rust and apply plenty of wob.
      In-situ similar repair for rear arch
      Clean and polish
      Service engine
      Adjust tracking
      Leave patina and enjoy the car as it is
       
      I will update this thread once progress is made.
       

       

       

       

       

       

       

       

       

       
      Hopefully these two will become good friends.
       

×
×
  • Create New...