strangeangel Posted April 13, 2016 Share Posted April 13, 2016 I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën. So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated. Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers. Link to comment Share on other sites More sharing options...
Matt Posted April 13, 2016 Share Posted April 13, 2016 Height lever problem: My XM had the same problem with the height lever except it wouldn't go to the lowest setting. Someone suggested that the runner/guides under the car that the shaft runs through can become clogged up with shit and that a clean and lube would be the first step in trying to solve it. RE the tyres: You could probably get away with the 185/65/14's but your speedo will under read by -1.59% plus whatever discrepancy they have from the factory. In other words 30mph = 29.52mph and 60mph = 59.04mph plus whatever the original discrepancy is. Not ideal but better than it reading slower than you are actually going. strangeangel and UltraWomble 2 Link to comment Share on other sites More sharing options...
Cavcraft Posted April 13, 2016 Share Posted April 13, 2016 You don't want to go too wide on the wheels or tyres, 5.5J best, you might get away with 6 if lucky. They foul on the rear arms, especially if the latter are leaning a bit. Seem to recall I just scraped by with 195/60/14s but 65s (or less) are better. strangeangel 1 Link to comment Share on other sites More sharing options...
Six-cylinder Posted April 13, 2016 Share Posted April 13, 2016 I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën. So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated. Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers. The height lever always was stiff, just needed a good tug to get it locked in position. strangeangel 1 Link to comment Share on other sites More sharing options...
Six-cylinder Posted April 13, 2016 Share Posted April 13, 2016 You don't want to go too wide on the wheels or tyres, 5.5J best, you might get away with 6 if lucky. They foul on the rear arms, especially if the latter are leaning a bit. Seem to recall I just scraped by with 195/60/14s but 65s (or less) are better. It was running on 6J with 195/60 14 and in spite of the rear arches being trimmed it was hard to get them on and off. Nothing seemed to rub while being driven though. rainagain and strangeangel 2 Link to comment Share on other sites More sharing options...
forddeliveryboy Posted April 13, 2016 Share Posted April 13, 2016 Check the linkage at the rear (it's all simple mechanical levers, rods and joints) and clean/grease. The handle in the car can take a bit of a pull to stick it in max height, but not to the point of excess. Is that clear as mud? I think the GTis had 185/60/14s on 6" rims, when I ran them they were £200 bangers so used whatever they came with, but I seem to remember the sweetest combination was a car with 175/65s fitted. Any pics? strangeangel 1 Link to comment Share on other sites More sharing options...
dollywobbler Posted April 13, 2016 Share Posted April 13, 2016 Warning. Do not reach or crawl under a BX unless it is on stands. But yes, the linkage needs greasing. It shouldn't be too stiff. Regarding level, if the yellow marker is resting on the top of the globe at normal height, it's probably not too far off. strangeangel, UltraWomble, costadelglosta and 1 other 4 Link to comment Share on other sites More sharing options...
forddeliveryboy Posted April 13, 2016 Share Posted April 13, 2016 Yes, don't get squashed. Blood and LHM don't mix, terrible mess to clear up after. strangeangel 1 Link to comment Share on other sites More sharing options...
strangeangel Posted April 13, 2016 Author Share Posted April 13, 2016 Thanks for all the helpful suggestions, will have at it on the weekend and see if I can't improve the lever action a bit. The 205 wheels are 5.5J so should be OK Any pics? Sorry, thought everyone had seen (or owned) it by now! Here's a slightly flattering one: loserone, DSdriver and Cleon-Fonte 3 Link to comment Share on other sites More sharing options...
UltraWomble Posted April 14, 2016 Share Posted April 14, 2016 BX's are ace - and well bought that man. The HP set up is quite easy to live with once you get your head around it and even stripping the doesur (sic) valve isnt the end of the world - somewhere on the internet are some very informative pictures from @Vanny of this parish ( and the BX Project) who has stripped and refurbed one. agreed about having a quick look and lube underneath - but only with the car on axle stands - I really cant stress this enough as Ive had one crush a 2.5L tin of bitumen in seconds when it dropped ( resulting in a North West "Face of Christ" on the driveway for several months). Ive had 195's on one of mine and apart from needing to slightly modify the rear spats with a piece of wood all was well, but if the rear arm bearings are shagged they will rub. Tickman and strangeangel 2 Link to comment Share on other sites More sharing options...
Inspector Morose Posted April 14, 2016 Share Posted April 14, 2016 Height corrector - It's okay, just needs a firm tug to get to the high position. Wheels - It did run 165s when it was on steels. 195 you can get away with on the front (bought some in error but it was a shame not to use them) and 185s will go under the rear but will rub when on lowest setting. Rear arms lean a nib but don't affect the clearance. DO NOT rely on the suspension to get under the car. The rear goes down pretty quickly (an hour or two) but the front stays up pretty well. I know this machine pretty well. strangeangel and chaseracer 2 Link to comment Share on other sites More sharing options...
KruJoe Posted April 14, 2016 Share Posted April 14, 2016 I believe this is the look he's going for: :D The Moog, chaseracer, Inspector Morose and 2 others 5 Link to comment Share on other sites More sharing options...
strangeangel Posted April 14, 2016 Author Share Posted April 14, 2016 ^^^ paint's not as nice as mine, but yeah, that's the idea Health and safety squashage warnings duly heeded - stands will be deployed at all times Inspector Morose 1 Link to comment Share on other sites More sharing options...
strangeangel Posted April 29, 2016 Author Share Posted April 29, 2016 Freshly powdered and wearing new Uniroyal Rainexperts; they cost more then the car, and they ain't been balanced yet! Logic: FAIL but on all other levels: WIN, I think. skattrd, Dick Longbridge, chaseracer and 9 others 12 Link to comment Share on other sites More sharing options...
Fabergé Greggs Posted April 29, 2016 Share Posted April 29, 2016 Freshly powdered and wearing new Uniroyal Rainexperts; they cost more then the car, and they ain't been balanced yet! Logic: FAIL but on all other levels: WIN, I think.They look great, I was always tempted by a set for mine... Link to comment Share on other sites More sharing options...
KruJoe Posted April 29, 2016 Share Posted April 29, 2016 Are they on the car yet? The Moog, Lacquer Peel and strangeangel 3 Link to comment Share on other sites More sharing options...
KruJoe Posted April 29, 2016 Share Posted April 29, 2016 How about now...? strangeangel, Lacquer Peel, chaseracer and 1 other 4 Link to comment Share on other sites More sharing options...
strangeangel Posted April 29, 2016 Author Share Posted April 29, 2016 How about now...? Much as I'm tempted, they'll only have to come off for balancing & I can't get them done before next week, what with work and the Bank Holiday. Still tempted though Link to comment Share on other sites More sharing options...
KruJoe Posted April 29, 2016 Share Posted April 29, 2016 Do it!You might find they don't even need balancing, coz new tyres etc... Link to comment Share on other sites More sharing options...
strangeangel Posted May 6, 2016 Author Share Posted May 6, 2016 YEAH BABY But while fitting one of the rears I discovered BAD NEWS. Photo isn't great but there's leakage from somewhere around here: I'm off to work in a bit but further investigation will be made shortly. Arse. StefanD, vulgalour and egg 3 Link to comment Share on other sites More sharing options...
dollywobbler Posted May 6, 2016 Share Posted May 6, 2016 Oh dear. Good news is it's probably a brake line. That's good because a full front-to-rear pipe failure is a right ballache to sort out. That visible pipe does a bit 'past best.' strangeangel 1 Link to comment Share on other sites More sharing options...
Fabergé Greggs Posted May 6, 2016 Share Posted May 6, 2016 On the plus side those wheels look flippin great strangeangel 1 Link to comment Share on other sites More sharing options...
strangeangel Posted May 20, 2016 Author Share Posted May 20, 2016 Still haven't done anything about the LHM escape, largely because of doing-up-the-house type stuff, but also now that one of the 205s CV joints has shat itself the BX is officially Number One Car. I did manage to discover why the throttle action was so heavy though, even with a new cable. The soundproofing under the dash had dropped down and was catching on the very top of the pedal mechanism - now fixed! Cleon-Fonte 1 Link to comment Share on other sites More sharing options...
dollywobbler Posted May 20, 2016 Share Posted May 20, 2016 Still haven't done anything about the LHM escape, largely because of doing-up-the-house type stuff, but also now that one of the 205s CV joints has shat itself the BX is officially Number One Car. I did manage to discover why the throttle action was so heavy though, even with a new cable. The soundproofing under the dash had dropped down and was catching on the very top of the pedal mechanism - now fixed! Phew. That's good, because BX's can suffer from pedal box collapse. Clutch or accelerator can fail. Link to comment Share on other sites More sharing options...
billyboy406v6 Posted May 20, 2016 Share Posted May 20, 2016 Keep going, this is a great thread to follow from my armchair. Link to comment Share on other sites More sharing options...
DSdriver Posted May 20, 2016 Share Posted May 20, 2016 Citroens like to "mark their territory" when they go somewhere new. Cleon-Fonte and hauserplenty 2 Link to comment Share on other sites More sharing options...
Ghosty Posted May 20, 2016 Share Posted May 20, 2016 rimz_yo! strangeangel 1 Link to comment Share on other sites More sharing options...
strangeangel Posted May 24, 2016 Author Share Posted May 24, 2016 Citroens like to "mark their territory" when they go somewhere new. Lacquer Peel 1 Link to comment Share on other sites More sharing options...
vulgalour Posted May 24, 2016 Share Posted May 24, 2016 Those wheels are a relief. catsinthewelder and Lacquer Peel 2 Link to comment Share on other sites More sharing options...
KruJoe Posted May 24, 2016 Share Posted May 24, 2016 It lays fried eggs!? strangeangel and mat_the_cat 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now