Jump to content
danthecapriman

Project Capri. Carpet and underfelt, pg.38.

Recommended Posts

My auntie had a mk2 3.0 auto ghia in blue she inherited it from her dad when he passed away, he had it for as long as I can remember, he worshipped that car and she ran it into the ground and let it rot away, sold it for peanuts around 2001 this made me sad, I wish I could remember the registration I can remember the first part SOO, my aunties name is sue as well, but the rest of the reg I can't remember

 

It looked like this

post-4828-0-45952600-1457038799_thumb.jpg

Share this post


Link to post
Share on other sites

Leather?  Velour, Shirley?

I don't know if you could get velour on mk2 seats tbh? I wonder if american Capris had options like velour given their love of the stuff back then.

Which leads me on to another retarded dream of mine! I've always wanted to bring over a septic spec mk1 with those huge hideous bumpers... I bet you can get them pretty cheap in the US, bring them to the UK by the container load, wack on some euro bumpers and sell for £megaoldskoolFord monies!

 

I'll try to find a trimmer and see what the options are about re trimming into black, vinyl probably is better.

The original seats had black vinyl outer bolster bits with the seat centre strip in black cloth. They were hopelessly worn and ripped to shreds but probably could be re trimmed and new foam added.

The brown seats are full vinyl, they're in good condition and would probably be a shame to strip down and re cover so depending what a trimmer can do with the old seats I might end up selling the brown ones on after. Just have to see. They don't half make your back sweaty in summer though!

Share this post


Link to post
Share on other sites

My auntie had a mk2 3.0 auto ghia in blue she inherited it from her dad when he passed away, he had it for as long as I can remember, he worshipped that car and she ran it into the ground and let it rot away, sold it for peanuts around 2001 this made me sad, I wish I could remember the registration I can remember the first part SOO, my aunties name is sue as well, but the rest of the reg I can't remember

It looked like this

attachicon.gifford-capri-mk2-3-0-ghia-wed-66-s.jpg

Stunning! That's pretty much made my mind up as far as colour is concerned!

Just like that but with no vinyl roof and no side trims, as mines a peasant spec.

 

Anyone know if these early mk2's should have wing mirrors or door mirrors? I've seen some mk2's with wing mirrors but they could just be non standard add ons.

The chrome door mirrors it's wearing now are nice enough and came off a scrapped mk1 Fiesta and will most likely be going back on again, just wondering if it 'should' have wing mirrors or not?

Share this post


Link to post
Share on other sites

Look forward to seeing how this is going to progress and I'm an advocate for sticking with a known firm when you've been happy with the results before. I reckon it's also admirable that you've got an established fleet and are willing to spend the cash on them - I reckon a lot of us would aspire to that dogged mentality! Didn't know you'd owned it so long, either. (I'm sure someone on here bought a brown MkII Capri a while back?)

 

Anyway, here's my opinion on a car I don't own: since it's been colour changed and is no longer as sold, I fully condone a change from the silver, as in all honesty it's a bit boring nowadays. Anyway, here's the colour chart for Fords from June '74:

 

 

newsletter10339.jpg

 

 

 

I'd say your interior was Tan, so combining paint choice with the chart below, you can have pretty much anything, bar silver or your personal favourite, Miami Blue.

 

 

 

 

newsletter10340.jpg

 

 

HOWEVER, tan was available with every colour, just limited to Ghia only models with some, so I'm sure it'd look fine with anything. Miami Blue is very nice but a bit 'Trigger' nowadays (he's claimed that shade on here) but what about Onyx Green? Here's an NZ Capri (not my photo) registered June '74, so obviously built months earlier:

 

GreenCapri.jpg?fit=742%2C511

 

 

Oh yeah, please re-instate the steels and get a set of raised digit number plates if you don't already have some!

 


 

Share this post


Link to post
Share on other sites

That colour chart and trim availability is interesting. I think my current seats are actually called saddle or dark saddle. Maybe it won't look too bad with a blue paint job?

 

Just have to see I suppose, I think I'm 99% decided on going for Miami blue. If I'm going to do this I want to make it exactly the way I want.

Agreed about the silver, it's not a bad colour but, as you say it's just a bit boring and I don't think it's really what I want, more a case of chasing the original shade.

 

Its already wearing a set of raised digit number plates, they look much better than the modern acrylic type.

Wheels, I did have a set of original steels with chrome centre caps but they were pretty rusty so in the end I binned them! Kept the chrome caps though. Maybe I'll try to find another set of steals and get them reconditioned? I do like the mk3 Laser 4 spokes though!

Share this post


Link to post
Share on other sites

My auntie had a mk2 3.0 auto ghia in blue she inherited it from her dad when he passed away, he had it for as long as I can remember, he worshipped that car and she ran it into the ground and let it rot away, sold it for peanuts around 2001 this made me sad, I wish I could remember the registration I can remember the first part SOO, my aunties name is sue as well, but the rest of the reg I can't remember

 

It looked like this

attachicon.gifford-capri-mk2-3-0-ghia-wed-66-s.jpg

 

That's Hawaiian blue, an altogether nicer, richer shade. 

Share this post


Link to post
Share on other sites

Love the idea of browsing the colour and trim charts and picking out the spec almost like its 1974 all over again. I like Miami blue and roman bronze but equally like the green used on the rs3100, Modena green? Which is a bit marmite but I like it.

Share this post


Link to post
Share on other sites

Here we go again! The first bill landed on the door mat yesterday.

 

Current state of play is the car has pretty much been stripped right out, seats, trims, carpets etc all removed and various bits of the bodywork have been taken off and it's having a thorough inspection of it's bodyshell.

Once that's complete it'll be time for some decisions to be made about how far I want the work to go. The engine sounds like it's ok but as you'd expect it does need a few things sorting.

There's obvious things like shocks (all fucked), brake lines and hoses (all in less then ideal condition), and since the engines coming out I'll go for a new clutch kit at the same time. I think getting all these things done at the same time as the body work and paint is going to be a good idea and save hassle at a later date.

They did ask if I had or knew of anywhere to find a new front valance panel, as mines battered and rather rusty. Unfortunately these are unavailable for mk2's so they said they'll get their body shop guys to roll and fabricate a new one from steel sheet. This, in my mind is exactly why I think paying for this is the best decision, there's no way I could do this sort of thing properly at home on the drive with basic hand tools!

 

In other news, the new carpet set arrived on Friday and looks gorgeous in black. Lovely job they made of it.

And I've found my spare bumpers, hidden away in the loft. They are much straighter than the ones on the car but the chrome isn't as good in a couple of spots so I think maybe a strip down of the straighter spares and a rechrome will be in order. Both mounting brackets are good on the spare front bumper too, one has rusted and snapped in half on the ones currently on the car.

Hopefully I'll be able to get some pics of the new parts pile in the next few days once I've spoken to the retsto guys about dropping it all in to them.

Share this post


Link to post
Share on other sites

Another update!

 

The guys rang me this morning to see if I could come in for a meeting about the Capri now it's been stripped and they know what work is required. I've just got back home from the meeting and they said it's a very good car and worth putting the work into!

 

So, body wise,

It's pretty good generally. Front wings are dead, which I knew about. Lower A posts and front inner sills/footwells do need attention. The front wings will be getting cut off and while they are off the floors and A post/inner sill area will be repaired before the new wings go back on.

Front valance will as a minimum have new repair panels rolled and welded on where it meets the wings.

Front screen surround needs stripping and welding, again I knew about this.

Rear mk3 spoiler has been removed already, there is rust under it so this needs cleaning back to see how deep into the metal it goes before repair or replacement of the tailgate.

Bumpers, one good pair built from the two pairs I have, including a re chrome if needed.

 

Then it needs a complete repaint, and I've made my decision on that. Yep you guessed it, it's going blue!

They said, since I've made that decision that they though silver wasn't the best colour choice and they agree that if were doing all this then I need to make sure it's made into the car I want it to be.

So they are going to spray me a test piece in Miami blue and one in Hawaiian blue before the final decision is made. Good idea I think.

When it's painted, that will be an engine out job and cover all door shuts, engine bay etc etc.

 

Mechanically,

The engine is good on compression and runs ok, but it does smoke a bit on cold startup so probably needs valve seals changing.

I've also got them to give the engine an internal inspection, and maybe a bore hone, set of rings and new crank bearings if needed.

New brakes at the front, new brake lines and hoses, replace the missing rear brake adjusters.

New rear shocks as they are completely fucked!

Diff will get a drain down, clean up and new oil.

Gearbox needs a new rear oil seal and oil change.

Prop UJ will be changed to get rid of an annoying vibration.

Steering column bushes will be replaced.

Exhaust system is good but has a couple of loose leaking joints which they will fix when it's reinstalled.

 

I've also got some interior work to be done at the same time,

Seats and door cards will be going back to black. Either recovering the original seats or using the brown ones currently fitted but re trimmed, same for the door cards.

New dash top, assuming we can find a good one!

New seals and rubbers all round.

New carpets and headlining.

 

I've also asked about wheels, the current plan is to keep an eye out for some good original wheels with the chrome centre caps and recon them, or if not then I'm happy to keep the 'Laser' 4 spokes but get them re conditioned. This sort of thing is a long way off yet though. The wheels will then be given a new set of tyres as the current ones are old and starting to crack on the sidewalls.

 

 

I'm pleased they are so thorough with it and said it's up they will take photos of the work and keep me updated as it goes ahead. They also seem very excited to be able to do this work too, and do an early basic car all the way from start to finish! Its nice to have people work on your car that feel that way about what they're doing, and I've been reassured it will be done to the highest standards. Tbh I expect nothing less after the work they did on the Mercury. I'm 100% sure it's in the right place and in the right hands.

 

So that's it, so far. I've given them the go ahead to start work. It won't be a quick job and it's not going to be cheap either but this will make the car as good as it should be.

It's going to be an expensive year.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By strangeangel
      I thought I'd start a thread for this as I'll probably end up asking all sorts of questions, given that this is my first 'proper' Citroën.
       
      So... the ground clearance lever won't go all the way to the highest setting (all others work), which is bad 'cos the book says I need it to do that in order to check the LHM level. It feels like something's seized, so I don't want to force it. Any ideas for a plan of attack would be much appreciated.
       
      Next up are the wheels. I now have a set of 205 pepperpots that have just gone off for powder coating & I need to get some tyres for them. The handbook says the car should have 165/70R14s on, the wheels came with 185/65R14 on. Any thoughts about what size I should get please? Cheers.
       
    • By PhilA
      Well, here we go again. I bit the bullet and bought me this.
       

       

       
      It's still up at the lot right now, there will be a miniature Collection Thread embedded in this thread when I go fetch it. Hopefully if the weather's good, that'll be this weekend.
       
      So, what is it?
       
      As the title suggests, it's a 1951 Pontiac Chieftain.
      It's got a flat-head straight eight hiding in the engine bay, 4.4 litres of it. It's bolted to a 4-speed Hydra-Matic Drive gearbox. No torque converter on this one, just a fluid coupling. 116 horses at a screaming 3700 RPM, 240lb/ft at 2000. It idles at 375 RPM. Redline just shy of 4k.
      Did I mention it's quite big? Sixteen foot eight from end to end and it seats six people in comfort. Every door has a quarter-light, too. Comfort is provided by properly sized tyres and (quite surprisingly for the age of it) double independent wishbone front suspension. Steering is via worm/wheel steering box so is moderately direct and the brakes are hydraulic drums all round. Modern and scientific!
       
      It's an honest example; looks to have had a "restoration" about 15-20 years back and the rust is coming through the seams and filler. The bottoms of the door skins have gone, the bottom of the A-pillars have gone (the front doors, on a single hinge a piece still open and close with one finger!) And it's got a couple holes and blebs in all the places you would expect.
      Not much electrical works. It needs to be completely rewired because someone has "converted" it to 12V. Thankfully it was originally negative ground so that's a good start. Gauges and such can be driven from a 6V bucking converter.
      Engine has had some work done on it- starts and runs nicely with very little greb coming out of the exhaust. It's got a few gaskets that need replacing and the tappets need some major adjustment, the gearbox engages gears correctly, the steering is okay but has a lot of slack in the center and the brakes work well, dont sink or feel spongy but need adjustment.
       
      More to come. I'll post up more pictures when I get it home.
       
       
      --Phil
    • By rainagain
      With a growing family I found I needed a car with six seats, I really didn’t want to end up with a people carrier so I looked at estates with seats in the boot. I really wanted a diesel V70 after owning an S80 but I couldn’t find one I could afford. I looked at 307 SW/estates and found an estate being advertised seriously cheap that just needed ‘brake pads’.  I had the slightly stupid idea of fitting the rear seat mounts and seat belts from a 307 to this estate to save money as the estates are so much cheaper than the SWs.
       
      Before even seeing the car I sent a cheeky text offer of just slightly more than half the advertised price and the owner accepted, it had been her grandad’s car then she had been using to transport her dogs around but now didn’t need. The viewing was a bit mixed it had obviously been sitting for a while as all the discs were rusted up, the ‘brake pads’ it required turned out to be an ABS fault, both this and the stability control lights were on. It had some giffer parking marks on the bumpers and one of the rear doors. The inside stunk of fag smoke and dogs and there was dog hair all over the back half of the car. The clutch/DMF made a slight squeaky noise that went away when you pressed the clutch, whilst the spare wheel was lying in the boot as the carrier mounts had dropped off.
       
      However it was my OH that discovered the best bit, whilst sitting in the car she pressed a button next to the hand brake and the electric roof cover rolled back, this wasn’t an estate, it was the more expensive glass roofed SW complete with all seat mounts and belts in the boot and better than that it was the SE edition so second top of the range! I gave it a quick drive around their estate as it wasn’t taxed and insured and it seemed to go ok. Back at their home I haggled another £50 off due to the ABS fault and the car was mine.
       
      A days insurance purchased and I started to head to my dad's, the drive home resulted in more dash light bingo.
       
       

×
×
  • Create New...