Jump to content

Tickman's stuff. 205 MOTed and for sale


Tickman

Recommended Posts

So picking up where I left off I needed a piece to join some stuff together so I bent an off cut and drilled some holes.

 

post-17457-0-26081800-1485962176_thumb.jpg

 

Then I stuck it in place.

 

post-17457-0-92679000-1485962181_thumb.jpg

 

I then made a piece that stuck the inner sill to the bits I have already done but the pictures didn't come out for some reason.

 

Next was to drill some holes in the outer sill piece.

 

post-17457-0-05281400-1485962186_thumb.jpg

 

Then use some clamps.

 

post-17457-0-17438400-1485962191_thumb.jpg

 

I did some squeezing of the trigger and some hitting with a hammer and got this.

 

post-17457-0-19651800-1485962197_thumb.jpg

 

That is all the metal bits stuck back together.

Next was a really weak piece of chassis leg on the drivers side at the back of the car. 

I got some thicker metal and battered it over in the vice (too thick for the folder) to make a U and put it over the weak piece after it was cleaned up. I started welding it in.

 

post-17457-0-52569200-1485962210_thumb.jpg

 

When I got to the inner side the brake lines and fuel lines are right next to this so I obviously stripped out the tank fuel tank and moved all the pipes put a sheld in the way and took loads of time keeping the area cool.

 

post-17457-0-83605500-1485962403_thumb.jpg

 

After that I cleaned up and put rust converter on quite a few places.

 

post-17457-0-91238900-1485962407_thumb.jpg

 

 

Until next time.....

Link to comment
Share on other sites

I have done some more on this today.

I finished the drivers side and set to the passenger side with a very unhappy chassis rail which had been patched twice so I did this.

 

post-17457-0-10682400-1486479233_thumb.jpg

 

I measured for the U section I would need and got the markers out.

 

post-17457-0-37299800-1486479240_thumb.jpg

 

Then into the folder and fold.

 

post-17457-0-25144200-1486479248_thumb.jpg

 

Then turn it round.

 

post-17457-0-64435400-1486479255_thumb.jpg

 

And fold.

 

post-17457-0-24137400-1486479265_thumb.jpg

 

Amazing* fabrication*

 

post-17457-0-31311900-1486479271_thumb.jpg

 

Stuck in the gap and welded for the next 40 minutes so as not to set the underseal and carpet on fire.

 

post-17457-0-41502200-1486479277_thumb.jpg

 

Then I welded up the blow at the bottom of the down pipe on the manifold, no pictures, imagine an exhaust with a split where it was welded then imagine the crack welded over.

Time to check the board of jobs and it would appear that I have covered the failure points. I wonder what my MOT guy will find for me. I am also assuming the emissions failure was related to the split exhaust (hopefully)

 

post-17457-0-69608100-1486479281_thumb.jpg

 

There is a fair bit of tidying up after myself to do before I take it anywhere and I need to get some paint on the bits I have ruined fixed.

Link to comment
Share on other sites

I think I must take credit / blame for the bits that have been ruined, it looks like you are doing a thorough job of putting everything right. Keep up that good work :)

 

You might be looking at an advisory on a couple of those tyres, I had a different set of wheels on it when it was in for test last time.

Link to comment
Share on other sites

I think I must take credit / blame for the bits that have been ruined, it looks like you are doing a thorough job of putting everything right. Keep up that good work :)

 

You might be looking at an advisory on a couple of those tyres, I had a different set of wheels on it when it was in for test last time.

There appears to be quite a lot of patches, not all are fresh by any stretch of the imagination.

 

No worries regarding the tyres all expected and in hand. 

Link to comment
Share on other sites

General tinkering day today.

Rear brakes of the Toledo adjusted up making the handbrake much more useful.

A few rust spots treated just to keep it at bay and a general tidy up.

Routine stuff so no pictures because I was just getting on with it.

Tomorrow might be a greasing session which will be thrilling*

Link to comment
Share on other sites

No pictures as I was a little messy today.

Some chassis black has been spread about various places underneath and today was underseal time.

A few years ago I bought a Dinitrol kit with a gun that goes on the compressor and has quick release tubes that either go in chassis legs or is quite directional.

I used the directional one today and except for a slight mishap where it was basically pointed at my face all went well.

 

I 'think' all the previous failure points have been addressed and now I need to look for insurance and get it in for an MOT to see what else is found!

Link to comment
Share on other sites

  • 2 weeks later...

I took the MX5 for an MOT on the 21st and my MOT guy found a few issues that were not dealt with.

One was a patch of welding needed at the front that I could only see while the car was over the pit which is why I had missed it in my thorougher* prep of the car.

The front left caliper was leaking, rear left handbrake was poor and emissions fail with a CO of over 4.

Caliper replaced, handbrake adjusted and welding done it just left the emissions which I had no way of testing.

I did oil, oil filter, air filter, new plugs and a bottle of Wynnes emissions magic.

 

Today was the first chance to get back so I took an indirect route from Forfar to Carnoustie using quite a bit of the rev range. It took me an hour to do a at most 30 minute journey and lots of fun was had.

 

I arrived at the garage and had a quick chat then got the car in. Headlights were adjusted (these were also a fail but I didn't count it) and emissions were tested with the result of 0.034% yes that is 0.034% I am well impressed with that.

Welding and caliper checked from underneath and a check of the handbrake resulted in one of these:

post-17457-0-06215400-1488383784_thumb.jpg

 

So officially 

post-17457-0-30933800-1488383665_thumb.png

 

 

As Carnoustie is quits a nice place I took this:

post-17457-0-75549700-1488383770_thumb.jpg

 

Obviously on the way home it started to hail so I put the roof up, then I got home and taxed it :)

Link to comment
Share on other sites

Great news on the pass, looks like a lot of effort went into that. My Aunt lives in Carnoustie, used to be there at least twice a year, it's a cracking place. Not been for about 5 years now though as she prefers to get away and come down. The front near the Golf Hotel is a grand place for pictures.

Link to comment
Share on other sites

Toledo time,

Sonic has on quite a few occasions given trouble starting. This has involved the bendix on the starter not being thrown out when the key is turned. It is completely unpredictable so after one occasion where it didn't even want to work after being persuaded with the jack handle (the usual what is handy tool) I decided I better have a look.

With the front up on ramps access to the bottom bolt is very easy and with the top being almost as easy from above it took a short amount of time to have this on the bench. First I cleaned 45 years of muck off it and had this:

post-17457-0-98844800-1488547957_thumb.jpg

post-17457-0-66919200-1488547968_thumb.jpg

 

I was quite surprised by the spacers and locating plate as I haven't seen one like this before. 

 

Testing the movement of the bendix by hand I could feel it was notchy. I had some Graphite lubricant in a spray from Lidl and used that to get smooth movement. I know that I cannot leave it wet in any way as muck from the clutch will stick to it and make it just as bad if not worse so I cleaned off any residue that had not evaproated with a dry cloth and movement was very smooth still.

 

I put it back in and it seems to have made a difference, as if it is meshing better with the flywheel. It turns over more consistently and doesn't do some of the things that I had put down as being 'Triumph' so I am happy with that.

 

Next was keeping it stopped, Chuck has been having trouble with the handbrake, this is mainly not being able to pull it on enough to keep the car still on real hills (of which we have a few in Dundee) so I had another look at this. I managed to adjust the cables and now it holds much better, I think a little backing off of the cables is required to get a comfortable height.

 

I checked the fluid in the master cylinder and it was a cloudy mess. This was all new last year but the car has had quite a baptism of fire regarding use level compared to the semi retirement it has been used to. I sucked all this out with the oil pump thing and flushed about 750 ml of fluid through the whole system. 

I wish I had done this months ago as it has made a massive difference to the feel and performance of the brakes.

 

Next on the fleet list is an MOT for Malcolm the camper closely followed by Sonic's second MOT with me.

 

Until next time (which will be hopefully sometime next week) 

Link to comment
Share on other sites

Oi, stop making so much progress, you're making me feel bad!

 

Got one of these stickers yet?

 

attachicon.gifs-l300.jpg

I am just trying to catch up on the progress you made last year....

Also hope any potential thief will have seen me in the car and will assume correctly that no hair products will ever need to be nearby, if they are looking for polish I might be in trouble though.

Link to comment
Share on other sites

  • 3 weeks later...

Malcolm the camper needed a new MOT, I went to a different MOT place as my usual place had a doorway too low :(

It predictably failed but only on both sidelights not working, one headlight insecure and a rear wheel bearing. Not too bad.

I ordered the wheel bearing kit (about £22) and started messing about with the side lights which I discovered were rusty connectors, that was quite easily sorted with a bit of sand paper and I treated it to new bulbs (£1.75). Lastly was the insecure headlight, this I fixed by pushing the headlight back onto the ball/socket thing.

I took it back and left with one of these. 

post-17457-0-46671900-1490195246_thumb.jpg

 

After this win the universe was out of balance and imminent doom was not far away!

The Volvo decided that Friday afternoon was a great time to restore balance and completely shit its water pump.

This was a slight inconvenience as Marianne was going out later and had offered to be designated driver. She had not driven the MX5 at this point so took it for a quick spin and came back grinning like the Cheshire Cat!

 

Today after the Ice age had started to melt I thought I better get the Volvo fixed! I stripped out the 'old' pump (only about 2 years old, probably a shit ECP one) and fitted a new one. This would have been dead easy if access was better but was still not to bad. After the pump was fitted I did a compression test as had suspicions of a failed Head gasket. 150 PSI exactly over all 4 cylinders. The plugs all even with that nice brown colour and after putting it back together the slight 'miss' seems to have gone away.

 

So that is another one 'fixed' but I will be checking the water level after every drive fo the next week or so.

 

No doubt the universe is now in danger again, hope I don't have to be the one to regain the balance though.

Link to comment
Share on other sites

This looks suspiciously modernz sir!

 

Indeed it is. Newest car I have bought!

I hope those 2 illuminated bars between the dials fluctuate as the car speaks to you in a slightly camp voice.

No voices (except in my own head)

 

Introducing the obviously named Nicole:

post-17457-0-44064800-1490781699_thumb.jpg

 

Getting a bit full in here:

post-17457-0-84910400-1490781643_thumb.jpg

 

Drives really nicely, has a few issues but nothing that is frightening.

I have bought much worse for a lot more money, hopefully I will not have to buy again!

Link to comment
Share on other sites

  • Tickman changed the title to Tickman's stuff. 205 MOTed and for sale

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By tommotech
      Having fetched this French delight from deepest, darkest Norfolk (well Norwich actually) in an underwhelming collection, for no other reason than the van was scooped up onto a trailer for its journey home, it was time to see what was needed.
       
      I knew a RH side load door was needed, luckily an item was procured for £20 from a guy breaking a Scudo. I drove across to Swadlincote in the van and it proved to drive well, as expected from wuvvum’s write up. On the way home it started surging when the fuel level dropped below quarter on the gauge, again as expected.
       
      Door was fitted and adjusted on return, it was even the same colour!
       
      During the week I looked at the rear doors and fettled and adjusted the locks / latches.
       
      Today I dropped the fuel tank and found a loose baffle, along with crud in the fuel pick up / tank unit. A road test will be the proof of this repair.
       
      I also achieved a working temperature gauge today and changed the power steering fluid out.
       
      The to do list includes a coolant flush, new tyres (cracked side walls), new discs and pads, LH door slider and lock handle, a deep interior clean and removal of the ladder rack. In the meantime have some photos.
       

       

       

    • By rusty_vw_man
      Been a serial lurker and occasional poster of nonsense, but have never quite got round to posting some pictures and the ongoing tribulations of being a serial VW licker.
      First a disclaimer - I like old VWs, partly as I grew up with them and partly because I understand how the work and I can fix* them. I do not like the 'scene' attached to them, it seems to attract too many of a certain type of person I am often allergic to - they bring me out in a shouty rage. 
      First car was a'69 beetle in red, driven flat out everywhere  until the rust took it. This was followed by a succession of Mk2 golf , vauxhall omega (vauxhall being close to VW in the sales ads)  a free Mk3 golf which was dire and tried to kill me multiple times. I have no photos of any of these as they were pre-camera phone and mostly awful. 
      Then came a T25 camper bought using generous donations from friends and family at our wedding . Bought, and a week later after hovering 15 years of dog hair out of it, we drove it all the way to northern Norway on honeymoon. Used it for a while.
      Bought a vauxhall astra estate (again, it was almost a VW in the sales section). It sucked. It did a year of commuting then it was scrapped. Was gifted a skoda fabia estate by my dad as a sensible run around. 
      During this time my wife wanted a sensible runaround for her and the kids, so we bought a bright orange 1971 beetle (rusty of course) which was excellent fun. People were openly critical of apparent lack of regard for our offsprings safety. I pointed out it had seat belts.
       Due to rusting the T25 was sold as a project, the Skoda was sold for being too dull and a T2 purchased.
      Here is the peak of VW ownership, where the beetle, bay and T25 are all in one place just before sale:

      So now we had two aircooled vehicles, the newest of which was  made in 1973.
      This lasted for exactly 9 months., during which I did lots of this:

      to be repeatedly rewarded with this:
       
      When the breakdown driver asks how the kids are getting on, you know you've seen him too much....
      I also conducted some invisible repairs on the rusty bits of the beetle. I'll point them out if anyone can't see them:

      A promotion and car allowance then allowed me to purchase a C3 Picasso (best not ask, I hate it). Its purple. I feel like a dick when I drive it. 
      Beetle then had to go due to third child and not enough seats, but it had the good engine, the van did not. A swap occurred. My neighbors love* me and find my antics endearing*. I clearly have no need for a drive or garage.

      After 1 too many FTPs, I was told van or family. I chose family and the van left. 
      I then went a looked at another T25 minibus (three kids now) and was in much trouble for even considering another van. 
      Two weeks later, after some small* arguments* we were in total agreement* and the van was purchased. 
      Roughly 18 months ago - note lovely laqueer peel, mismatched rear wing and low level tide mark:

       

      After some light fiddling I have made a very basic day van affair, and we dragged it with camping gear and the three kids all the way up to the arctic circle in Finland last summer (wife has family in that part of the world).
      6 days before departure I noticed the rear suspension had a bit of paint hanging off. I pulled and it showed this below:

       
      Trip to machine mart, a google of "mig wleding for numpties" and a youtube video later and I'd made this:

      and away we went. 
      Here it is in a moody B&W photo  in the land of the midnight sun, which really brings out the high quality paint. the rear suspension is still attached though, so winning. 
       
      That's an epic catch up post really, but will use this space now to document the exciting* repairs and work done on it to keep everything attached .and working.... 
    • By Broadsword
      I think the Broadsword fleet has become sufficiently complicated to merit a combined thread so that gradually all new additions will appear in one place.
       
      As of Sunday 17th March the situation is interesting.
       
      Two Citoren Xantias (remember the white Xantia of Excellence is for sale people!)
      http://autoshite.com/topic/34699-w-reg-citroen-xantia-20-hdi-xantia-of-excellence-%C2%A3999/
      http://autoshite.com/topic/34596-citroen-xantia-double-madness-rust/page-2
       
      A turquoise XJR6 pending overdue-collection (need that gone now!)
      http://autoshite.com/topic/34003-jaguar-xjr6-double-madness-double-sold
       
      An XJS 3.6 manual project which will get in high gear soonish. Wont be a keeper but will be fun getting it back to something presentable. Drivers fantastic!
      http://autoshite.com/topic/34664-jaguar-xjs-36-manual
       
      A Range Rover P38, which is turning out to be really rather good.
       
      And to mix things up even more I'm off on a collection caper today. Had first refusal on it and was expecting it to come around in a year, but things soon changed and no way was I going to pass up on it. It may well render the second Xantia redundant as I've got a really good feeling about this motor.
       
      In the meantime here are some snaps of the Range Rover. As usual it was a car I said I would probably never buy due to their reliability*. I have said the same of Jag XJR, XJS, XK8 and I have had all of those now. Basically the moment I declare buying a particular car is impractical or improbable, I end up buying one.
       
      Things to note on the P38. It's a nice colour with tidy body. The EAS has been removed. It runs and drives lovely and it doesn't have enough electrical problems to hinder progress. The main one is the driver's side window not working, but that should be fixable. I've tried changing the outstation, that didn't fix it. Might be wiring under the seat. Other than that I bought it and took it for an MOT the very next day, and it passed. Since then it had what seemed like a battery drain, but since unplugging the RF thingy for the remote locking and putting on a proper lead-acid battery, which the car can actually charge, unlike the modern lead-calcium batteries, it has been perfect. I will treat it to a full service soon.
       
      Stay tuned for the latest collection later today!



    • By Zelandeth
      Well I've been meaning to sign up here in forever, but kept forgetting. Thanks to someone over on another forum I frequent poking me about it recently the subject was forced back into my very brief attention span for long enough to get me to act on the instruction.

      I figure that my little varied fleet might bring you lot some amusement...

      So...we've got:

      1993 Lada Riva 1.5E Estate (now fuel injected, as I reckon the later cars should have been from the factory...).
      1989 Saab 900i Automatic.
      1987 Skoda 120LX 21st Anniversary Special Edition.
      1985 Sinclair C5.
      2009 Peugeot 107 Verve.

      Now getting the photos together has taken me far longer than I'd expected...so you're gonna get a couple of photos of each car for now, and I'll come back with some more information tomorrow when I've got a bit more time...

      Firstly...The Lada. Before anyone asks - in response to the single question I get asked about this car: No, it is not for sale. Took me 13 years and my father's inheritance to find the thing.


      Yes, it's got the usual rusty wings...Hoping that will be resolved in the next couple of months.

       






      Next, a proper old Saab. One of the very last 8 valve cars apparently, and all the better for it. I've driven two 16v autos and they were horrible - the auto box works sooooo much better with the torque curve of the 8 valve engine. Just wish it had an overdrive for motorway cruising...









      Next up a *real* Skoda...back when they put the engine where it belongs, right out the back. In the best possible colour of course...eye-searingly bright orange.







      Seat covers have been added since that photo was taken as it suffers from the usual rotting seat cloth problem that affects virtually all Estelles.

      Then we have possibly the world's scruffiest Sinclair C5...



      Realised when looking for this that I really need to get some more photos of the thing...I use it often enough after all! We have a dog who's half husky, so this is a really good way of getting him some exercise.

      Finally - again, I really need to take more photos of - we have the little Pug 107.



      Included for the sake of variety even if it's a bit mainstream! First (and probably to be the only) new car I've bought, and has been a cracking little motor and has asked for very little in return for putting up with nearly three years of Oxford-Milton Keynes commuter traffic, before finally escaping that fate when my housemate moved to a new job. Now it doesn't do many miles and is my default car for "when I've managed to break everything else."

      I'll fill in some more details tomorrow - I warn you though that I do tend to ramble...
    • By vulgalour
      Fackin oops.
       

       
      My goal was not to buy any more cars but with the Lanchester out of action while we work through it and make it safe to use, and the Princess out of action and needing the engine to be removed (a job I am procrastinating about, and when I'm motivated am thwarted by schedule and weather conflicts) it was getting more obvious that I needed some personal transport.  Something basic and reliable that I know my way around, that's going to be cheap to buy and run.  This is an ideal candidate, on paper.
      Whether I really can just use it as An Car or will end up getting all finicky about making it nice remains to be seen.  I just want some hasslefree pootling for a few months and normally Maestros are just that.
×
×
  • Create New...