Jump to content

Tickman's stuff. 205 MOTed and for sale


Tickman

Recommended Posts

After doing side A it was time to turn the record over and play side B.

I decided to take some quality* pictures this time!

Wheel off, caliper suspended from my trusty bungy cord which took 10 minutes to find even though I had used it the day before. The super useful Aldi air gun can be seen waiting on the track rod end nut for the compressor to charge, the blow torch that was used is just out of shot. Both sides these were very stubborn!

post-17457-0-03008200-1481884868_thumb.jpg

Strut top cleaned and marked with cheap copy version of a sharpie from Home Bargains (would recommend) this helped me with my static alignment of the front suspension!

post-17457-0-34991600-1481884874_thumb.jpg

Something missing here, wonder where it is?

post-17457-0-80700000-1481884880_thumb.jpg

Found it, this side was no lighter than the other side but I was at least expecting it.

I was well impressed with the spring compressors from Screwfix, they never looked like they were at risk of moving while being tightened/loosened. Also the air gun did most of the work on these as well.

post-17457-0-43826300-1481884887_thumb.jpg

 

Happily with it all back together and another new track rod end fitted and adjusted it was time to tidy up and go home. 

Volvo now drives much happier. 

 

With everything on this side moving as it should I now need to get the caliper mount for the drivers side ordered and fitted when it arrives, then sort out the bit of rot under the battery then.......

Link to comment
Share on other sites

  • 4 weeks later...

The Volvo has been back in for some more love because sod and his law have been hard at work.

 

The new shock fitted decided to leak quicker than the Titanic so they were changed again, I am getting quite quick at this now!

I have a noisy diff so I then started the car up to turn it round and the exhaust was blowing from the centre section :(

I topped up the diff but it only took a tiny amount so that is not going to cure anything!

While under it I discovered the rear strap that goes round the back box had rotted out putting more strain on the centre section creating the blow. A new strap will be going on tomorrow for the sum of £7.68. 

 

While out for a bit of food with friends before Christmas I was asked to recommend an MOT place for their daughter to get her 57 plate Punto tested, this led to me taking it yesterday and ending up with a fail for a broken spring and some minor bits sorted at the time of test.

Today involved swapping the spring and drop link out (use of grinder was required for the drop link) which resulted in a fresh certificate for the next 12 months. not bad for £96 including the test fee.

 

 

 

In other fantastic Volvo news I bought one of those UV dye kits off ebay and added the contents to the coolant system.

I can throughly recommend the dye kit, unfortunately I cannot recommend the Volvo head gasket.

 

At least I now know where the magic coolant is disappearing from :(

Link to comment
Share on other sites

Visitor in for surgery.

 

Something missing here:

post-17457-0-26529000-1484149873_thumb.jpg

 

One of these is not like the other:

post-17457-0-21308400-1484149868_thumb.jpg

 

 

It has just taken me about 15 minutes to get the pictures from my phone to Autoshite, I am sure you can agree it was worth* the effort!

 

Edit just checked and it was nearer 45 minutes. FFS.

Link to comment
Share on other sites

Good fred this; Toledos and their brethren are oft unappreciated wee cars. Interested to see what the Moggie is like underneath.

The underneath of the Minor is basically covered in 1/4 of an inch of grease and oil, the original owner obviously wasn't much of a clean freak but it has saved most of the original metal so I thank him for that.

 

Today was sorting out the 940 Exhaust. 

The strap from round the back box had rusted through so I had to secure it in place with some copper wire I had (all part of the rewire of the workshop) while I got another strap. 

Less than £8 at ECP and new strap fitted. I also sorted out the blow at the back of the cat in the system with a few spots of weld.

I would have done none of this without this as it was so cold!

post-17457-0-92411900-1484228442_thumb.jpg

 

Now just need to get a decent work light as my Lidl special finally died :(

Link to comment
Share on other sites

While teaching Chuck to drive I have had quite a few L plates decide they have had enough, they have been the magnetic ones but due to the shape of the Toledo they do not stay on the front, this one should for now:

post-17457-0-41620800-1484754186_thumb.jpg

Technically it should be removed when driven by anyone else but that will not be happening.

 

I have been sorting out my stock of batteries which have died on me and am trying to revive some of them so I went to Lidl and bought another one of there £13 chargers and set to it:

post-17457-0-99338000-1484754208_thumb.jpg

So far I have two that are below the minimum voltage to charge so I will piggy back them when I have the rest sorted:

post-17457-0-75701400-1484754224_thumb.jpg

 

While teaching Chuck last week we had someone drive across our path doing at least 30 where we had the priority so I decided to get the other dash cam fitted, I have been using a power bank to run it but it was never going to be a long term solution so today I dug out some scrap and fitted this:

post-17457-0-07799400-1484754239_thumb.jpg

It is a little two port USB socket I got from ebay.

I have room to add other things on the panel when the need arises so now the camera comes on automatically with the ignition.

Link to comment
Share on other sites

Got my indicators sorted, tried the auto electricians again and got served by someone who actually did their job.

Left with a Durite relay part number 0-744-12 added the earth to number 31, solid green to 49 and green with a strip to 49a and the job is done :)

Link to comment
Share on other sites

On a high created by the success of getting and fitting the correct relay for the Toledo today I decided to get the cloud to go along with the silver lining.

 

A little bit of background first, I have too many projects and am terminally lazy so when GM put his MX5 up for sale when it failed its MOT I decided it would be worth a look as everyone needs a red two seat convertible in their life, but hang on a second I have the Reliant SS1  :?

 

After confirming that I am a complete knob I got in touch with with GM and went and had a look. GM should be a salesman as we went out to play in his new black MX5 (as the red one had failed its MOT) for at least an hour (probably longer) during this time I was encouraged to have fun which I certainly did.

After as quick look over the red one I bought it there and then  :?

 

A train was booked for the following day and I turned up, sorted stuff out and headed home with a stop for fuel:

post-17457-0-90784100-1484837829_thumb.jpg

 

I took it steady battered it all the way back to the workshop in Forfar and parked it up:

post-17457-0-21344200-1484837803_thumb.jpg

After this I did nothing to it at all while I sorted out the road legal cars I have, that is until today.

 

So I got the car up in the air and started with the drivers side rear sill which had been plated for a previous MOT but failed the most recent one, lets see what we have here then:

post-17457-0-11267200-1484837346_thumb.jpg

That doesn't look too bad, lets have a closer look:

 

 

 

 

 

Oh!

post-17457-0-08371800-1484837338_thumb.jpg

 

 

Well that is quite a pile of scrap left on the floor.

post-17457-0-26971900-1484837329_thumb.jpg

 

 

It is exactly as I expected, there is some more to come out before stuff goes back in and I will see if I can make a neat job of it. I actually quite enjoy the welding stuff so I will see how it goes and keep you updated if anyone cares!

 

Well that is all for this week on cars, more next week hopefully when the welder comes out to play.

 

I am such an idiot!

 

 

 

Link to comment
Share on other sites

nice to see little AVO again, I wondered if you had forgotten about her :)

that sill isn't pretty, but I'm sure you will do a proper job and have an mot in no time. nice to see the line of trackday stickers are still there on the windscreen, that is about a years worth.

I've not done much with the black one yet, it's needing brake lines fitted and some fancy pads before the first trackday at the end of feb, looking forward to it already.

let me know if you are needing any parts, I've got a bit of a stash in the garage.

Link to comment
Share on other sites

Oooh, your workshop is only in Forfar, eh?

 

:D

Indeed it is, for some reason having loads of space seemed to turn into a challenge to fill it, a challenge I have excelled at!

 

nice to see little AVO again, I wondered if you had forgotten about her :)

that sill isn't pretty, but I'm sure you will do a proper job and have an mot in no time. nice to see the line of trackday stickers are still there on the windscreen, that is about a years worth.

I've not done much with the black one yet, it's needing brake lines fitted and some fancy pads before the first trackday at the end of feb, looking forward to it already.

let me know if you are needing any parts, I've got a bit of a stash in the garage.

Not forgotten at all, I told myself not to touch it before I had sorted out the two daily's. Thr sill is fine really, some of the patch was difficult to remove, most of it wasn't!

Is it another Saturday trackday you are doing? May have to look into that when I am further down the line. 

if you need a bit of a mojo boost, feel free to come down and have another go on the black one - so much fun

I am just going to plod on no deadline, just get it right, if I need.....

Link to comment
Share on other sites

cool. trackday is sat 26th feb, a mate has booked it but his mx5 is in bits waiting for turbo goodies to arrive so the plan is to use mine and spilt the costs. you will be most welcome to come along and jump in as a passenger with either of us, maybe even sign on as an extra driver and do a few laps if you are feeling dangerous :)

 

the February date has been postponed twice due to omgsnowkaos in recent years so fingers crossed for a mild period. hats and gloves on, roof down, it's the only way !

Link to comment
Share on other sites

While teaching Chuck to drive I have had quite a few L plates decide they have had enough, they have been the magnetic ones but due to the shape of the Toledo they do not stay on the front, this one should for now:

attachicon.gifIMG_20170118_1024295791.jpg

Technically it should be removed when driven by anyone else but that will not be happening.

 

 

My wife and I disagree with each other here.

She believes it is a banning offence (12 instant points) to drive with L plates when you have a full licence, and I believe that it is irrelevant, because whilst you must (should) have the L plates if you are on a provisional, it becomes a mere graphic if you have a full licence.  The worst that might happen is that people treat you with more respect.

Link to comment
Share on other sites

My wife and I disagree with each other here.

She believes it is a banning offence (12 instant points) to drive with L plates when you have a full licence, and I believe that it is irrelevant, because whilst you must (should) have the L plates if you are on a provisional, it becomes a mere graphic if you have a full licence.  The worst that might happen is that people treat you with more respect.

It is (or was at least) an offence to display L plates while not being driven by a driver with a provisional licence, the only exception being a qualified driving instructor. 

Also the last thing to happen is getting more respect, it used to amaze me the grief other drivers would give the car with L plates on no matter how it was being driven. (I was a driving instructor in the late 90's.)

 

cool. trackday is sat 26th feb, a mate has booked it but his mx5 is in bits waiting for turbo goodies to arrive so the plan is to use mine and spilt the costs. you will be most welcome to come along and jump in as a passenger with either of us, maybe even sign on as an extra driver and do a few laps if you are feeling dangerous :)

 

the February date has been postponed twice due to omgsnowkaos in recent years so fingers crossed for a mild period. hats and gloves on, roof down, it's the only way !

I would love to come along depending on what nonsense is going on round here allowing! I would only know nearer the time though.

Link to comment
Share on other sites

Today the Toledo received the nylon insert to the top bush of the steering column and the indicators now cancel properly every time and there is less rattling when doing 60/70  :)

 

Next up a bit of work on the MX5.

I did a but more cutting to to the rear sill end and ended up with this:

post-17457-0-95337700-1485190893_thumb.jpg

I bent up some metal and started piecing stuff back together.

Firstly the inner sill:

post-17457-0-61058500-1485190900_thumb.jpg

Once that was welded in I added a couple more bits of metal to build up the strength where it has rusted out, slowly piecing it back together.

post-17457-0-98888300-1485190905_thumb.jpg

 

A bit more to do later in the week with this bit and then move onto the next bit!

Link to comment
Share on other sites

Grand thread this, I love some pics of a bit of the old metal fabrication skills!

I was going to take some yesterday and when I realised I was on 13% (my camera phone, not me) I decided to just get on with it.

This is the first time I have done anything this complicated, there are 50 million pieces meeting in this area and most are knackered...

I am finding it very therapeutic.

Link to comment
Share on other sites

Just had Parts for Volvo on the phone regarding the shocks that were fitted and then failed, Bilstein have accepted the warranty return but no explanation, at least I got a full refund and know not to buy them in future.

 

That's quite a concern, as I was just about to press the button on 4 Bilsteins. We're they old new stock? Or are billy's yet another big brand bought for their name to sell us cheap tat at inflated prices?

Link to comment
Share on other sites

Have you fitted non standard wheels to the Toledo. I only ask cos I saw a blue Toledo diving into the rear entry of the Kingsway retail park the other day. Was it you

Yes it has black steels from an MGF on it. It was almost certainly me. If you get a chance say hello.

 

That's quite a concern, as I was just about to press the button on 4 Bilsteins. We're they old new stock? Or are billy's yet another big brand bought for their name to sell us cheap tat at inflated prices?

I was talking to the MOT tester when I took the Punto in for test and told him the saga and he said he would only fit Monroe, I assume years of work in a garage steers you towards certain parts!

 

Edit, they were new and no idea why the failure?

Link to comment
Share on other sites

I have only managed about 3-4 hours on this since and as Iain asked so nicely I thought I would take a few more pictures, I basically did a lot of prep work and stuck a few bits in.

 

Firstly always start with a clean and clear work bench

 

post-17457-0-58060900-1485900902_thumb.jpg

 

Also make sure the area around your work bench is clear.

 

post-17457-0-00431800-1485900906_thumb.jpg

 

OK so tidy up you messy bugger......

 

post-17457-0-57083600-1485900911_thumb.jpg

 

Much better, the bottom of the inner arch where it meets the sill and outer wing was well on the way to disappearing so I cut it out, I couldn't take a picture of it as after I cut it off there was nothing there!

 

I got some card and using all the skill guesswork I could find I came up with a rectangle, Wow!

Boosted by this success I made a rectangle out of metal!

 

post-17457-0-30126700-1485900917_thumb.jpg

 

I then put the metal in the quality* metal folder.... 

 

post-17457-0-31482300-1485900923_thumb.jpg

 

....and folded it. (the folder is not bad and is loads better than battering it over the jaws of the vice)

 

post-17457-0-05553900-1485900930_thumb.jpg

 

I then folded the other end and tried to get the curve and twist in it, I partly succeded

 

post-17457-0-43447800-1485900937_thumb.jpg

 

I did stick that bit in but didn't get any pictures as I was fed up with trying to get my head between the rear disc and the wheel arch. I actually got the welding helmet stuck in the 'gap' a few times.

 

Time to move on to making the sill piece, there are still other bits to do but I wanted a break from little jobs so I got a flat sheet and bent up the seam which meets the inner sill and strengtheners at the bottom. Then the end of the sill to wheel arch bend was folded up

 

post-17457-0-01720500-1485900942_thumb.jpg

 

Then the shrinker was used to make it roughly the correct shape, luckily the bench has wheels so the distance from the bench to the car was small as it was back and forward many times to get the shape.

 

post-17457-0-49527500-1485900945_thumb.jpg

 

That is where the day ended having made this.

 

post-17457-0-96509300-1485900948_thumb.jpg

 

 

Until next time, hopefully later this week when it can go on the car.

Link to comment
Share on other sites

  • Tickman changed the title to Tickman's stuff. 205 MOTed and for sale

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By tommotech
      Having fetched this French delight from deepest, darkest Norfolk (well Norwich actually) in an underwhelming collection, for no other reason than the van was scooped up onto a trailer for its journey home, it was time to see what was needed.
       
      I knew a RH side load door was needed, luckily an item was procured for £20 from a guy breaking a Scudo. I drove across to Swadlincote in the van and it proved to drive well, as expected from wuvvum’s write up. On the way home it started surging when the fuel level dropped below quarter on the gauge, again as expected.
       
      Door was fitted and adjusted on return, it was even the same colour!
       
      During the week I looked at the rear doors and fettled and adjusted the locks / latches.
       
      Today I dropped the fuel tank and found a loose baffle, along with crud in the fuel pick up / tank unit. A road test will be the proof of this repair.
       
      I also achieved a working temperature gauge today and changed the power steering fluid out.
       
      The to do list includes a coolant flush, new tyres (cracked side walls), new discs and pads, LH door slider and lock handle, a deep interior clean and removal of the ladder rack. In the meantime have some photos.
       

       

       

    • By rusty_vw_man
      Been a serial lurker and occasional poster of nonsense, but have never quite got round to posting some pictures and the ongoing tribulations of being a serial VW licker.
      First a disclaimer - I like old VWs, partly as I grew up with them and partly because I understand how the work and I can fix* them. I do not like the 'scene' attached to them, it seems to attract too many of a certain type of person I am often allergic to - they bring me out in a shouty rage. 
      First car was a'69 beetle in red, driven flat out everywhere  until the rust took it. This was followed by a succession of Mk2 golf , vauxhall omega (vauxhall being close to VW in the sales ads)  a free Mk3 golf which was dire and tried to kill me multiple times. I have no photos of any of these as they were pre-camera phone and mostly awful. 
      Then came a T25 camper bought using generous donations from friends and family at our wedding . Bought, and a week later after hovering 15 years of dog hair out of it, we drove it all the way to northern Norway on honeymoon. Used it for a while.
      Bought a vauxhall astra estate (again, it was almost a VW in the sales section). It sucked. It did a year of commuting then it was scrapped. Was gifted a skoda fabia estate by my dad as a sensible run around. 
      During this time my wife wanted a sensible runaround for her and the kids, so we bought a bright orange 1971 beetle (rusty of course) which was excellent fun. People were openly critical of apparent lack of regard for our offsprings safety. I pointed out it had seat belts.
       Due to rusting the T25 was sold as a project, the Skoda was sold for being too dull and a T2 purchased.
      Here is the peak of VW ownership, where the beetle, bay and T25 are all in one place just before sale:

      So now we had two aircooled vehicles, the newest of which was  made in 1973.
      This lasted for exactly 9 months., during which I did lots of this:

      to be repeatedly rewarded with this:
       
      When the breakdown driver asks how the kids are getting on, you know you've seen him too much....
      I also conducted some invisible repairs on the rusty bits of the beetle. I'll point them out if anyone can't see them:

      A promotion and car allowance then allowed me to purchase a C3 Picasso (best not ask, I hate it). Its purple. I feel like a dick when I drive it. 
      Beetle then had to go due to third child and not enough seats, but it had the good engine, the van did not. A swap occurred. My neighbors love* me and find my antics endearing*. I clearly have no need for a drive or garage.

      After 1 too many FTPs, I was told van or family. I chose family and the van left. 
      I then went a looked at another T25 minibus (three kids now) and was in much trouble for even considering another van. 
      Two weeks later, after some small* arguments* we were in total agreement* and the van was purchased. 
      Roughly 18 months ago - note lovely laqueer peel, mismatched rear wing and low level tide mark:

       

      After some light fiddling I have made a very basic day van affair, and we dragged it with camping gear and the three kids all the way up to the arctic circle in Finland last summer (wife has family in that part of the world).
      6 days before departure I noticed the rear suspension had a bit of paint hanging off. I pulled and it showed this below:

       
      Trip to machine mart, a google of "mig wleding for numpties" and a youtube video later and I'd made this:

      and away we went. 
      Here it is in a moody B&W photo  in the land of the midnight sun, which really brings out the high quality paint. the rear suspension is still attached though, so winning. 
       
      That's an epic catch up post really, but will use this space now to document the exciting* repairs and work done on it to keep everything attached .and working.... 
    • By Broadsword
      I think the Broadsword fleet has become sufficiently complicated to merit a combined thread so that gradually all new additions will appear in one place.
       
      As of Sunday 17th March the situation is interesting.
       
      Two Citoren Xantias (remember the white Xantia of Excellence is for sale people!)
      http://autoshite.com/topic/34699-w-reg-citroen-xantia-20-hdi-xantia-of-excellence-%C2%A3999/
      http://autoshite.com/topic/34596-citroen-xantia-double-madness-rust/page-2
       
      A turquoise XJR6 pending overdue-collection (need that gone now!)
      http://autoshite.com/topic/34003-jaguar-xjr6-double-madness-double-sold
       
      An XJS 3.6 manual project which will get in high gear soonish. Wont be a keeper but will be fun getting it back to something presentable. Drivers fantastic!
      http://autoshite.com/topic/34664-jaguar-xjs-36-manual
       
      A Range Rover P38, which is turning out to be really rather good.
       
      And to mix things up even more I'm off on a collection caper today. Had first refusal on it and was expecting it to come around in a year, but things soon changed and no way was I going to pass up on it. It may well render the second Xantia redundant as I've got a really good feeling about this motor.
       
      In the meantime here are some snaps of the Range Rover. As usual it was a car I said I would probably never buy due to their reliability*. I have said the same of Jag XJR, XJS, XK8 and I have had all of those now. Basically the moment I declare buying a particular car is impractical or improbable, I end up buying one.
       
      Things to note on the P38. It's a nice colour with tidy body. The EAS has been removed. It runs and drives lovely and it doesn't have enough electrical problems to hinder progress. The main one is the driver's side window not working, but that should be fixable. I've tried changing the outstation, that didn't fix it. Might be wiring under the seat. Other than that I bought it and took it for an MOT the very next day, and it passed. Since then it had what seemed like a battery drain, but since unplugging the RF thingy for the remote locking and putting on a proper lead-acid battery, which the car can actually charge, unlike the modern lead-calcium batteries, it has been perfect. I will treat it to a full service soon.
       
      Stay tuned for the latest collection later today!



    • By Zelandeth
      Well I've been meaning to sign up here in forever, but kept forgetting. Thanks to someone over on another forum I frequent poking me about it recently the subject was forced back into my very brief attention span for long enough to get me to act on the instruction.

      I figure that my little varied fleet might bring you lot some amusement...

      So...we've got:

      1993 Lada Riva 1.5E Estate (now fuel injected, as I reckon the later cars should have been from the factory...).
      1989 Saab 900i Automatic.
      1987 Skoda 120LX 21st Anniversary Special Edition.
      1985 Sinclair C5.
      2009 Peugeot 107 Verve.

      Now getting the photos together has taken me far longer than I'd expected...so you're gonna get a couple of photos of each car for now, and I'll come back with some more information tomorrow when I've got a bit more time...

      Firstly...The Lada. Before anyone asks - in response to the single question I get asked about this car: No, it is not for sale. Took me 13 years and my father's inheritance to find the thing.


      Yes, it's got the usual rusty wings...Hoping that will be resolved in the next couple of months.

       






      Next, a proper old Saab. One of the very last 8 valve cars apparently, and all the better for it. I've driven two 16v autos and they were horrible - the auto box works sooooo much better with the torque curve of the 8 valve engine. Just wish it had an overdrive for motorway cruising...









      Next up a *real* Skoda...back when they put the engine where it belongs, right out the back. In the best possible colour of course...eye-searingly bright orange.







      Seat covers have been added since that photo was taken as it suffers from the usual rotting seat cloth problem that affects virtually all Estelles.

      Then we have possibly the world's scruffiest Sinclair C5...



      Realised when looking for this that I really need to get some more photos of the thing...I use it often enough after all! We have a dog who's half husky, so this is a really good way of getting him some exercise.

      Finally - again, I really need to take more photos of - we have the little Pug 107.



      Included for the sake of variety even if it's a bit mainstream! First (and probably to be the only) new car I've bought, and has been a cracking little motor and has asked for very little in return for putting up with nearly three years of Oxford-Milton Keynes commuter traffic, before finally escaping that fate when my housemate moved to a new job. Now it doesn't do many miles and is my default car for "when I've managed to break everything else."

      I'll fill in some more details tomorrow - I warn you though that I do tend to ramble...
    • By vulgalour
      Fackin oops.
       

       
      My goal was not to buy any more cars but with the Lanchester out of action while we work through it and make it safe to use, and the Princess out of action and needing the engine to be removed (a job I am procrastinating about, and when I'm motivated am thwarted by schedule and weather conflicts) it was getting more obvious that I needed some personal transport.  Something basic and reliable that I know my way around, that's going to be cheap to buy and run.  This is an ideal candidate, on paper.
      Whether I really can just use it as An Car or will end up getting all finicky about making it nice remains to be seen.  I just want some hasslefree pootling for a few months and normally Maestros are just that.
×
×
  • Create New...