Jump to content

Shite in Miniature II


Split_Pin

Recommended Posts

On 3/22/2019 at 11:54 AM, Datsuncog said:

That there is a Matchbox Superkings Mercury Commuter race support car... it should be kind of a lime green, but has been heavily 'weathered' (brown Humbrol...) - if you fancy having a bash at saving it, I'm sure it'll strip back to bare metal ok?

Right then...

I took a proper look at the Mercury station wagon, and it's not very pretty:

20190322_133805.jpg

Busted a-posts (both sides), broken front screen and very worn wheels made this one a bit borderline, in my view, even if the mess of enamel paint can be scraped off.

I asked how much, wondering if he'd do it for 50p, say, but no - £4 was the price on it!

Four pounds!

Yeesh.

I think not. I'm afraid I put it back. I'm sure you can find a better one for much less. I sold a decent one on here last year for a pound or two.

Guess this is the problem with stalls like this - pricing can be somewhat variable, depending on the whims and caprices of the stakeholder. He wasn't very chatty this morning.

Also at £4, were each of the Superkings Jags.

20190322_133841.jpg

While the blue one was conceivably worth it, the police one was missing its assorted bells and whistles and certainly wasn't. I took the blue one.

Also picked up the acid green Citroen SM, for the same money. Not in bad nick overall, though the rear glazing seems to have gone walkabout.

Overall verdict: stay away when stallholder grumpy.

Link to comment
Share on other sites

Ah, so here is the Phantom suspension piece, it is different to the later Lesney ones. It is a bit bent, so following Marty from down under under, I will be applying hot water to see if I can straighten it.

 

attachicon.gifIMG_20190322_151718~2.jpg

attachicon.gifIMG_20190322_151747~2.jpg

 

Could you leave it on a radiator or use a hair dryer perhaps?

Link to comment
Share on other sites

attachicon.gifMatchbox Commuter - B.jpg

 

attachicon.gifMatchbox Commuter - A.jpg

 

This thing got repainted. I had to paint the interior because so much of the interior is visible through the massive glazed area. 

 

The Vita-Min has also been repainted, I didn't try to match the original colour, but it had to stay purple! 

 

attachicon.gifCorgi vitamin - B01.jpg

 

attachicon.gifCorgi vitamin - A01.jpg

 

Nice work on the Freeman Commuta, it looks much more like the "real" one did when I saw it as a kid in the Telegraph magazine.

Link to comment
Share on other sites

post-5335-0-94110800-1553270545_thumb.jpg

 

post-5335-0-38317300-1553270554_thumb.jpg

 

I found what the kit was originally, had a clue on the chassis inside the car where it's got Revell copyright 196-something cast in.  It's a very old kit that's been re-released a few times and the version I got must have been the Monogram one because I do remember it having this box art.

 

monogram_tbirdbox-lg.jpg

 

That would also explain why the whole thing is painted purple underneath the other repaints.  I've no idea what happened to the bubble canopy (that I don't actually like) or any number of the other smaller details I would have liked to still have, like the mirrors and the rear seat cover.  Ah well.  The original plastic is actually cleaning up quite well, even though it's thoroughly stained with whatever paint I used.  There's some areas I had been really heavy with a coarse file and it looks like a lot of it was built with superglue which in a funny sort of way is a saving grace since the purple meths does a great job of turning that brittle and lifting it off the plastic base without damage.

 

The other neat thing is that I did such a bad job of sticking the bonnet down the purple meths broke the glue down and now the panel opens and is undamaged.  It's also clear it got the scoop extension, which I'll retain once I've tidied it up a bit better.

post-5335-0-78642400-1553271038_thumb.jpg

 

I shan't be glueing the roof on, I'll leave it loose.  This means I can display it with or without and means I can do a really nice job on the interior.  About the only interior bit missing is the instrument binnacle, it's the same shape as the glovebox/blank I still have for the other side so I should be able to build something that at least looks the part and fits using stuff from the bits box.

post-5335-0-87457400-1553271130_thumb.jpg

 

post-5335-0-99033100-1553271152_thumb.jpg

Link to comment
Share on other sites

Figured I might as well make a start on this today. One advantage of its previous restoration being that it came apart with a flat bladed screwdriver.

 

post-26064-0-74634400-1553274746_thumb.jpg

Either Norn Iron's sunnier than I've been given to understand or this was overly close to some powerful shit. I'd like to think the former.

post-26064-0-89445900-1553274927_thumb.jpg

Paint was tenacious in a few places, unsurprisingly since this is evidently no stranger to Humbrol. So far as I can make out it was either dark green or pale blue to begin with although it's also been grey and a truly violent pink at some stage.

post-26064-0-80439000-1553275129_thumb.jpgpost-26064-0-76929100-1553275187_thumb.jpg

Hopefully primer and maybe even paint tomorrow. After replacing the rear screen pillar obvs.

Link to comment
Share on other sites

This very nice Ertl Pontiac Bonneville had an appointment with the airbrush today. 

 

post-17021-0-16816300-1553287572_thumb.jpg

 

post-17021-0-66701300-1553287577_thumb.jpg

 

Few more challenges in this one - there was a massive hole in the roof to fill (ex police?), followed by a world of painful masking for the roof then even more masking to paint that bright strip. 

Link to comment
Share on other sites

Made my first attempt at dents.

 

First job is to smooth a piece of kitchen foil over the panel you want to dent.  This is quite a satisfying thing to do, like unwrapping sweet wrappers to smooth them out.  Maybe that's just me.  With the foil blank set aside you then drill a stonking great hole on the bodyshell where you want the dent and hope that you know what you're doing.  After that, sharp clippers to turn the round hole into a more dent shaped hole and after that hand file and rotary tool to thin out the material so it's not such a hard step between the body and the hole.

 

Then, carefully offer up the foil blank and superglue it to the edge of the hole before figuring out just how much pressure to use, and where, to create the dent.  For a first shot, I'm okay with this, with experience I think I can do better, especially for the transition between bodywork and hole which is a little sharp in places.  On one side I added a couple of score lines to represent the car getting scraped along something.  It was tricky to make it look as I wanted to on the doors.  For the rear wing on the other side it was much easier and I think that one will need less work.

 

post-5335-0-74695900-1553291513_thumb.jpg

 

post-5335-0-20225800-1553291541_thumb.jpg

 

post-5335-0-34837400-1553291581_thumb.jpg

 

After getting the foil as I wanted it I then filled the back with epoxy, carefully, and left it to set.  When the epoxy has fully hardened I'll take a file and sandpaper and probably a bit of filler to the outside of the panel to see how good the dent looks without all the excess foil.  I rarely work with epoxy and foil so I'm well out of my comfort zone.  I also made a start on the interior, which will be green cloth and vinyl with a faded carpet.  I'm considering putting some cracks in the dashboard top since the interior presently looks far too nice for the state of the rest of the car.  I'm not going to put a crack in the windscreen, I need more practice at that before I risk it.

Link to comment
Share on other sites

Got a bit further on this tonight.  After trimming back the foil I applied a thin skim of filler to blend out the edges, some rough sanding, and then a light primer to see what I'm working with.

 

post-5335-0-69782700-1553306186_thumb.jpg

 

post-5335-0-71298700-1553306241_thumb.jpg

 

The rear wing dent is more convincing than the doors, though it needs much more sanding which probably means the doors mostly need more filler work to deform the edges of the dent slightly better.  For a first attempt I'm not unhappy with this, it shows promise.

 

post-5335-0-75228600-1553306298_thumb.jpg

 

post-5335-0-76656100-1553306304_thumb.jpg

Link to comment
Share on other sites

Here is a little oddity I found today.

 

post-5543-0-02472400-1553351403_thumb.jpg

 

Looks like a Matchbox Mercedes,yes?

 

post-5543-0-53210600-1553351454_thumb.jpg

 

Except it's not.

It's a Dinky!

Made in Bulgaria.

 

post-5543-0-16394600-1553351532_thumb.jpg

 

Alongside an original Matchbox version of the casting.

 

I've heard of Bulgarian made die cast cars,but have never owned one until now.

Another addition to the collection.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...