GingerNuttz

You're supposed cut the rust out instead of welding to it btw.

In primer start blocking it tomorrow for basecoat.

Could have welded the bloody hole up 🤣

About time !! Been chasing peeling paint for 3 weeks, could have hung myself 🤣

Paint at the weekend hopefully. Absolute nighhtmare, should have been bridged 😂

I need to fill over shit usually so I need to sand it anyways to get the mechanical bond with filler, used a wire brush a couple of times too and that worked well before sanding it.

Lucky if there was 30 tack welds on that whole pillar,I mean it just goes to show how strong a shit tack weld really is 😂 That isn't all the rot cut out either btw, I've had to leave structure to copy before I chop the lot out so it's gonna get 10x worse than it is atm. I've already got two of the panels made before I ran out of 1.2mm steel but I've got a sheet incoming tomorrow if Parcelforce aren't part of the strikes.

More pics. Arch is finished and panels are made for inner arch.

I mainly use it for tiny pits in steel like on the manta roof etc. I just douse it in it then I sand what I can back to bare steel leaving it in the bits I can't sand, shoot some primer then whatever top coat. Acid etch primer is just phosphoric acid in a primer so the acid may well be able to be painted over without sanding it back but I can't take that chance 😂

Always expect the worst then you can never be diapointed 😂

https://www.jennychem.com/products/biosan-super-concentrated?variant=15420606545969&currency=GBP&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic One I use gallons of.

Acid is only a temp solution tbh and anything rotten or rusty can only be fixed by cutting it out. Can hold it back foir a while with acid and a decent primer then top coat tho.

Only in for a bit on the bottom of the A pillar. had a couple of days to have a poke while I waited on gas so I could let Saabnut know how good or bad it would be.

Next foor neighbours car failed it's mot and the garage quoted her £1000 for this welding One side isn't even holed 😂 Best thing about it is my uncle is the mot tester in the place, shower of robbing bastards.

I have a fear of laying under cars since a Xantia fell on me back in the day so it's big overkill ramps for me these days. Fear of laying under cars while laying under cars welding 😂

Don't buy ramps, you can have em ones that are under the bench. I don't know where they came from but I wouldn't put anything heavier than the smaller of your cars on em 😂 These ones https://www.ebay.co.uk/itm/310652401556?epid=13038092932&hash=item4854537794:g:Ti8AAOSwQItULTXE&amdata=enc%3AAQAHAAAAoOkwkRDtHqBmQyWPIrAl3eGT0rEIMceXsKL1VdFTkgSwYS3%2FhLI0EI5u1HTICjrRGuMolNdf%2Fj5sSZeCH%2Fp%2BwK8Bu7vaQy9EnuiRvw0L4072p%2BlzHiwXZAgJfF78m07nZqQlO%2BgFynwfgp67lrFEB4VndxW4P5mknNZhEgwbzT4lbMhyKB3wzqXuycs0vV7TfBcnGSEsRTVOUh99jEhjAVw%3D|tkp%3ABk9SR9D34p6MYQ

Oh Clio of the lake, what is your wisdom? Convinced this car was like this 😂

We were gonna call our latest Jensen after the Interceptor but went with Dax after the Cobra kit cars since we have a girl named Shelby 😂

I'm hoping for blackout riots and looting so I can score some new gear from Machine Mart for gratis.

It's not bad when you have 2 whole sides off another car 😂 One side is done

Other side was rotten too but not as bad as the drivers.

320Touring's Clio 😂