Jump to content

1951 Pontiac Chieftain


PhilA

Recommended Posts

Nice work on the dash :) is that with LED bulbs? it gives it a vintage fluorescent Juke box look like its being backlit by an 8W T5 tube :) (I wonder if anyones ever done a fluorescent tube backlit dash? the closest I know to that was in aircraft where they used UV/Blue fluorescent Tubes to make fluorescent dials glow)

 

 

 

I'm making the bits nobody will ever see all nice and shiny.

 

^^ This was all you needed to say................ ever.

 

All this magic about wires and winding and stuff, it's just scary.

 

 

so on a scale of 1-10 how scared does this make you?  :mrgreen:

 

025.JPG

 

(just a small* thing I did back in early 2012 when I had a 1Kw Mercury lamp but not the correct ballast to run it with, so I lumped a bunch together to try and hit 1Kw, in the end I only managed about 500W before running out of ballasts)

Link to comment
Share on other sites

Ok, so with arrival of New Puppy a week or so earlier than anticipated, I've been on Puppy Duty since the dog arrived. Plans to work on the car this weekend utterly dashed, but I still need to make a list.

 

1. Pull speedometer out, take to pieces and grease up

2. Remove speedometer drive cable, clean, grease and reassemble

3. Remove wiper motor and disassemble to see why it doesn't work

4. Remove upper heater box and test heater valve for operation and matrix for leaks

5. Run water though lower matrix to check for leaks

 

That's a good enough list for now. I need to do things that take time, not money right now...

 

Phil

Link to comment
Share on other sites

Item 1: Speedo was removed, needle wouldn't come off, was scared to break it. Spooned some grease into the odometer drive bearings and put a drop of oil on the end race. Now turns smoothly.

 

Item 3: Removed wiper motor.

 

post-5454-0-38506300-1546296828_thumb.jpg

Pulled rooster head knob off gently.

 

post-5454-0-27224000-1546296867_thumb.jpg

Knocked the dial loose and removed the mechanism from under the dash.

 

post-5454-0-33016200-1546296910_thumb.jpg

A pair of spring clips and two 11/32" bolts later and the entire thing is out. Officially the easiest wiper motor to remove of all my cars. Is stamped Trico.

 

post-5454-0-20967500-1546296980_thumb.jpg

Popped the side off. Valve flip-flop.

 

post-5454-0-78378000-1546297022_thumb.jpg

Oiled the selector cable and drive mechanism and let it to sit and soak in.

 

post-5454-0-05827900-1546297070_thumb.jpg

Removed the lid. Inside is just a big flap that seals to the U shaped bucket. Vacuum is applied to one side, then the other, and there's a return valve to automatically park the wipers when you turn them off.

The grease had turned to the consistency of wax crayons, and the flap somewhat relies on the grease to form a tight seal. Cleaned up, regreased and reassembled.

 

post-5454-0-63878800-1546297203_thumb.jpg

Fresh grease in the valves.

 

post-5454-0-25154800-1546297227_thumb.jpg

Cleaned up and greased the bearings that the wiper arms attach to.

 

post-5454-0-64979700-1546297265_thumb.gif

Finally, connected up to the Renault on the vacuum tee for the brakes. It's got a decent bit of force behind it now. Looking at it, it'll move the wipers across most of the screen then really tuck them down tight to park.

Fun to watch. That's about half of maximum speed.

 

Phil

Link to comment
Share on other sites

My suspicions were correct. With the wiper motor disconnected, the wiper spindles are very stiff to turn, so they'll have to come out and be cleaned and lubricated also.

 

That should see the wiper mechanism working properly though. This makes me happier than it should, because following posts will have the word escutcheon in them.

 

Phil

Link to comment
Share on other sites

Pulled the wiper arms off and started on the easy side with the most access- through the hole left by the dash gauges.

 

post-5454-0-27672400-1546478168_thumb.jpg

Up in there is the locking bolt and backing plate for the wiper escutcheon.

 

post-5454-0-88867000-1546478244_thumb.jpg

Relatively easy access.

 

post-5454-0-49249400-1546478277_thumb.jpg

Then as with all these things, the plate was stuck to the body with the remains of the rubber seal. Gently prised off and everything came loose, including shearing the old washer pipe. That'll be replaced.

 

post-5454-0-58973800-1546478358_thumb.jpg

Entire assembly. Ball joint was gritty. Arm spindle itself would barely move.

 

post-5454-0-88919000-1546478400_thumb.jpg

Copious quantities of penetrating oil and then engine oil later and it spins around freely.

 

post-5454-0-79840000-1546478460_thumb.jpg

Cleaned up and ball joint greased; left to sit and drain down.

 

post-5454-0-52781500-1546478497_thumb.jpg

Had a bit of a poke at the surround, cleaned it up a little. I'll need to put some rust converter and a bit of paint before reassembly.

 

Going to go look in the catalog to see if they sell the rubber seals as the original one fell to pieces.

 

Other one another day because the glovebox really needs to come out to get at it.

 

Phil

Link to comment
Share on other sites

After a long day, tonight offered a few spare minutes.

 

post-5454-0-97322200-1546831638_thumb.jpg

I head out to the garage at sunset.

 

post-5454-0-36610800-1546831724_thumb.jpg

Randomly cleaned the car and put on a bit of wax.

 

post-5454-0-10875600-1546831763_thumb.jpg

Fight with the glovebox ended in victory.

 

post-5454-0-76878300-1546831795_thumb.jpg

Looking down the bolt hole on the passenger side showed a bit of a hole at the bottom that had a slight sign of rust inside. Figured that was the shaft and that I could probably get some grease into the bearings via this route.

 

post-5454-0-10243400-1546831889_thumb.jpg

Squeezed some grease in.

 

post-5454-0-15448800-1546831916_thumb.jpg

Screwed the bolt down into the grease. This proved moderately effective until the void inside was full. Then more grease escaped past the threads of the bolt than was forced though.

 

post-5454-0-18992300-1546831985_thumb.jpg

Had a thought and undid one of the grease nipples from the front suspension. Correct size to screw in.

 

post-5454-0-24748000-1546832032_thumb.jpg

Grease gun. Now we're cooking with gas.

 

post-5454-0-39042300-1546832061_thumb.jpg

Pumped and pumped and forced all the rusty muck out. Twisted the thing as I was pumping pressure in. This proved effective.

 

post-5454-0-77248800-1546832122_thumb.jpg

Cleaned up and smooth to operate! That's where I had wanted to be with them. Happy now they've got some decent lubrication inside. Did the other one as well and that's even more smooth to turn.

 

Another thing off the checklist.

 

 

Phil

Link to comment
Share on other sites

Escaped to the garage for a little while tonight.

 

post-5454-0-33930000-1546916822_thumb.jpg

Tools required: small scissors, pencil and paper. You can tell I have kids. Sparkly pink pencils obviously work much better than regular pencils.

 

post-5454-0-75280600-1546916915_thumb.jpg

Cut down, lined up. Made a rubbing off the edge of the cutout in the body and matched the shape of the old seal.

 

post-5454-0-25631400-1546917078_thumb.jpg

Checked for fit.

 

post-5454-0-63989500-1546917118_thumb.jpg

Drew around the perimeter of the paper with permanent marker onto sheet of high density foam rubber bought at the craft store for the rear lights on the Renault. It's a bit thick but it should squash down.

 

post-5454-0-19616100-1546917238_thumb.jpg

Twice.

 

post-5454-0-80115900-1546917283_thumb.jpg

Those of you without your Blue Peter badges will need to ask a grown up for help with this stage.

 

post-5454-0-93220600-1546917331_thumb.jpg

Finally all trimmed to fit. Looking okay, to be honest.

 

post-5454-0-23023300-1546917364_thumb.jpg

Final stage, application of some rust converter.

 

post-5454-0-45501100-1546917408_thumb.jpg

All gone over and wiped down. There's a few localized holes in the bodywork consistent of scratches, which is normal around bodywork trim. That'll all have to come off and have some new metal let in. Right now it'll probably just get some epoxy to stop the water getting in.

 

post-5454-0-18453200-1546917513_thumb.jpg

I'm not sure I like the car sporting the wiper-less look; the next step past that is fitting a Chevy small block and I'm not sure I want that.

 

Once the rust converter is dry it'll get a bit of non matching paint and then hopefully the wipers refitted.

 

Phil

Link to comment
Share on other sites

Plus, I've not done anything on the car recently because I have been suffering the MANFLU and haven't had the energy to do anything. I even took a day off work and lay in bed, close to death all day long.

 

Hopefully a semblance of normality will return by the weekend but I'm going to be busy with other things, interview on Monday in the city so busy busy.

 

Phil

Link to comment
Share on other sites

Escaped to the garage for a little while tonight.

 

attachicon.gif20190107_201258.jpg

Tools required: small scissors, pencil and paper. You can tell I have kids. Sparkly pink pencils obviously work much better than regular pencils.

 

attachicon.gif20190107_201704.jpg

Cut down, lined up. Made a rubbing off the edge of the cutout in the body and matched the shape of the old seal.

 

attachicon.gif20190107_202456.jpg

Checked for fit.

 

attachicon.gif20190107_202608.jpg

Drew around the perimeter of the paper with permanent marker onto sheet of high density foam rubber bought at the craft store for the rear lights on the Renault. It's a bit thick but it should squash down.

 

attachicon.gif20190107_202743.jpg

Twice.

 

attachicon.gif20190107_203055.jpg

Those of you without your Blue Peter badges will need to ask a grown up for help with this stage.

 

attachicon.gif20190107_204617.jpg

Finally all trimmed to fit. Looking okay, to be honest.

 

attachicon.gif20190107_204808.jpg

Final stage, application of some rust converter.

 

attachicon.gif20190107_205138.jpg

All gone over and wiped down. There's a few localized holes in the bodywork consistent of scratches, which is normal around bodywork trim. That'll all have to come off and have some new metal let in. Right now it'll probably just get some epoxy to stop the water getting in.

 

attachicon.gif20190107_205318.jpg

I'm not sure I like the car sporting the wiper-less look; the next step past that is fitting a Chevy small block and I'm not sure I want that.

 

Once the rust converter is dry it'll get a bit of non matching paint and then hopefully the wipers refitted.

 

Phil

 

9872453 points for sparkly pencil........

Link to comment
Share on other sites

Was feeling better when I came home.

 

post-5454-0-40052800-1547249524_thumb.jpg

 

Here, we have a perfect color match. Painted over the kurust.

 

post-5454-0-48180400-1547249668_thumb.jpg

 

Screws and some bulbs. Oddly the hardware store had a bunch of amber glass bulbs so I bought a pair. $2. Very dusty.

 

post-5454-0-89282200-1547249773_thumb.jpg

 

Fixed up with new stainless screws.

 

post-5454-0-73271200-1547251292_thumb.jpg

 

Looking better, not half hanging off any more. Seal is clamped down nicely too.

 

 

Phil

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...