Jump to content

Six Cylinders Motoring Notes - Well that didn’t go well!


Six-cylinder

Recommended Posts

How old would it have it been when you got it? I guess they were not considered very valuable that long ago?

 

It is a 1966 car which I bought in May 1982, it had been off the road since 1977. When we did the body we found the inner sills had been welded with heavy plate during its first 11 years on the road. It took me 6 years to get it back on the road in 1988. Since then although it has been stored without MOT from time to time it has always been on the road or close to it.

 

I paid £1000 for it in 1982 and spent £13,000 rebuilding it over 6 years to put it back on the road.

 

Now it is getting a bit tired and could do with a refresh of the paintwork, interior and suspension but there is no rot in the car.

 

I like all cars and get just as much pleasure out of my Citroen Visa. 

post-4787-0-18090900-1505222971_thumb.jpg

Link to comment
Share on other sites

It must be nice to have owned a car for that long and had it available on the road for use. I like the idea of being able to bimble down to the shops in an E-type to pick up a pint of milk.

 

But you will need to get yourself a couple of miniature Poodles to replace those Grey hounds of yours!

Link to comment
Share on other sites

But you will need to get yourself a couple of miniature Poodles to replace those Grey hounds of yours!

 

post-82-0-22265400-1505224501_thumb.jpg

 

Harold and Maude is a great film by the way if anyone has not seen it before.

 

https://petrolicious.com/articles/building-this-jaguar-e-type-hearse-was-quite-the-undertaking

Link to comment
Share on other sites

Another Good and bad day

 

Good the LNA drives and I got it home!

 

Bad because:

 

• The new anti roll bar bushes will not fit so we have had to refit the old ones, which are in good order.

• The window support channel I got has the wrong width for the lift wheels to run in.

• The steering wheel is breaking up and we went to change it for the one on my spares MK1 Visa and it did not fit as there is no self cancelling on the early Visa.

• Beko polishing part of the bonnet sent my coffee sliding off!

post-4787-0-17182500-1505316544_thumb.jpg

post-4787-0-78528200-1505316572_thumb.jpg

post-4787-0-42190600-1505316589_thumb.jpg

post-4787-0-92370000-1505316627_thumb.jpg

post-4787-0-52409600-1505316664_thumb.jpg

post-4787-0-51053700-1505316691_thumb.jpg

post-4787-0-11558000-1505316716_thumb.jpg

post-4787-0-04139200-1505316732_thumb.jpg

post-4787-0-82374000-1505316755_thumb.jpg

post-4787-0-50873100-1505316776_thumb.jpg

post-4787-0-16071200-1505316800_thumb.jpg

Link to comment
Share on other sites

I am not sure if I ever told the result of the Stag story.

 

Back in February my brother offered me his Stag that had been off the road for 10 years. (Page 43 post 1280) I bought it with my friend Derek and today we went to see what we had bought. We have got the front wheels to turn after taking the brake pad pins out. The rear wheels are jammed and we don’t know how to release them as we can’t get at the adjusters, we have tried a club hammer.

 

The engine turned with the plugs out using grips on the front pulley but locked at one point. You could back it off and it would also stick backwards. We removed the rocker covers but could not see anything wrong, then turning the crank with the grippes it just kept turning and all seemed well. My theory is there was a value stuck and it freed so the engine turned fine. We then used the starter and it spins over freely pumping up oil pressure. There may be a noise from the starter but it seems to work fine.

 

Next stage is to drain the stale fuel and get the SU fuel pump working.

post-4787-0-46720900-1505419873_thumb.jpg

post-4787-0-26890600-1505419894_thumb.jpg

post-4787-0-50234800-1505419908_thumb.jpg

post-4787-0-12856400-1505419922_thumb.jpg

Link to comment
Share on other sites

The Stag and BX GTi sit side by side waiting to see which is first out of the starting block, but today the BX jumped ahead after the new metal heater pipe was fitted that Ruffgezzer got me and all seems well. I gave it a short test drive on a private unmade road and I feel confident enough to book it an MOT near home, 30 miles away and drive it there.

 

I even gave it a wash, so now I just need to sort out the logistics of getting it to the MOT station.

post-4787-0-55851600-1505422525_thumb.jpg

post-4787-0-33214200-1505422544_thumb.jpg

post-4787-0-03742900-1505422561_thumb.jpg

post-4787-0-46593600-1505422577_thumb.jpg

post-4787-0-98991000-1505422597_thumb.jpg

post-4787-0-35513500-1505422625_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...